ACPI: thermal: add DMI hooks to handle AOpen's broken Award BIOS
Use DMI to:
1. enable polling (BIOS thermal events are broken)
2. disable active trip points (BIOS fan control is broken)
3. disable passive trip point (BIOS hard-codes it too low)
The actual temperature reading does work,
and with the aid of polling, the critical
trip point should work too.
http://bugzilla.kernel.org/show_bug.cgi?id=8842
Signed-off-by: Len Brown <len.brown@intel.com>
diff --git a/drivers/acpi/thermal.c b/drivers/acpi/thermal.c
index 3521c37..1e06159 100644
--- a/drivers/acpi/thermal.c
+++ b/drivers/acpi/thermal.c
@@ -33,6 +33,7 @@
#include <linux/kernel.h>
#include <linux/module.h>
+#include <linux/dmi.h>
#include <linux/init.h>
#include <linux/types.h>
#include <linux/proc_fs.h>
@@ -1328,10 +1329,74 @@
return AE_OK;
}
+#ifdef CONFIG_DMI
+static int thermal_act(struct dmi_system_id *d) {
+
+ if (act == 0) {
+ printk(KERN_NOTICE "ACPI: %s detected: "
+ "disabling all active thermal trip points\n", d->ident);
+ act = -1;
+ }
+ return 0;
+}
+static int thermal_tzp(struct dmi_system_id *d) {
+
+ if (tzp == 0) {
+ printk(KERN_NOTICE "ACPI: %s detected: "
+ "enabling thermal zone polling\n", d->ident);
+ tzp = 300; /* 300 dS = 30 Seconds */
+ }
+ return 0;
+}
+static int thermal_psv(struct dmi_system_id *d) {
+
+ if (psv == 0) {
+ printk(KERN_NOTICE "ACPI: %s detected: "
+ "disabling all passive thermal trip points\n", d->ident);
+ psv = -1;
+ }
+ return 0;
+}
+
+static struct dmi_system_id thermal_dmi_table[] __initdata = {
+ /*
+ * Award BIOS on this AOpen makes thermal control almost worthless.
+ * http://bugzilla.kernel.org/show_bug.cgi?id=8842
+ */
+ {
+ .callback = thermal_act,
+ .ident = "AOpen i915GMm-HFS",
+ .matches = {
+ DMI_MATCH(DMI_BOARD_VENDOR, "AOpen"),
+ DMI_MATCH(DMI_BOARD_NAME, "i915GMm-HFS"),
+ },
+ },
+ {
+ .callback = thermal_psv,
+ .ident = "AOpen i915GMm-HFS",
+ .matches = {
+ DMI_MATCH(DMI_BOARD_VENDOR, "AOpen"),
+ DMI_MATCH(DMI_BOARD_NAME, "i915GMm-HFS"),
+ },
+ },
+ {
+ .callback = thermal_tzp,
+ .ident = "AOpen i915GMm-HFS",
+ .matches = {
+ DMI_MATCH(DMI_BOARD_VENDOR, "AOpen"),
+ DMI_MATCH(DMI_BOARD_NAME, "i915GMm-HFS"),
+ },
+ },
+ {}
+};
+#endif /* CONFIG_DMI */
+
static int __init acpi_thermal_init(void)
{
int result = 0;
+ dmi_check_system(thermal_dmi_table);
+
if (off) {
printk(KERN_NOTICE "ACPI: thermal control disabled\n");
return -ENODEV;