Merge tag 'usb-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and PHY driver fixes from Greg KH:
"Here are some USB and PHY driver fixes that resolve some reported
regressions. Also in here are some new device ids.
All of the details are in the shortlog and these patches have been in
linux-next with no problems"
* tag 'usb-4.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (22 commits)
USB: cp210x: add ID for HubZ dual ZigBee and Z-Wave dongle
usb: renesas_usbhs: Don't disable the pipe if Control write status stage
usb: renesas_usbhs: Fix fifo unclear in usbhsf_prepare_pop
usb: gadget: f_fs: fix check in read operation
usb: musb: fix order of conditions for assigning end point operations
usb: gadget: f_uac1: check return code from config_ep_by_speed
usb: gadget: ffs: fix: Always call ffs_closed() in ffs_data_clear()
usb: gadget: g_ffs: Fix counting of missing_functions
usb: s3c2410_udc: correct reversed pullup logic
usb: dwc3: gadget: Fix incorrect DEPCMD and DGCMD status macros
usb: phy: tahvo: Pass the IRQF_ONESHOT flag
usb: phy: ab8500-usb: Pass the IRQF_ONESHOT flag
usb: renesas_usbhs: Revise the binding document about the dma-names
usb: host: xhci: add mutex for non-thread-safe data
usb: make module xhci_hcd removable
USB: serial: ftdi_sio: Add support for a Motion Tracker Development Board
usb: gadget: f_midi: fix segfault when reading empty id
phy: phy-rcar-gen2: Fix USBHS_UGSTS_LOCK value
phy: omap-usb2: invoke pm_runtime_disable on error path
phy: fix Kconfig dependencies
...
diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt
index dc2a18f..ddbe304 100644
--- a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt
+++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt
@@ -15,10 +15,8 @@
- phys: phandle + phy specifier pair
- phy-names: must be "usb"
- dmas: Must contain a list of references to DMA specifiers.
- - dma-names : Must contain a list of DMA names:
- - tx0 ... tx<n>
- - rx0 ... rx<n>
- - This <n> means DnFIFO in USBHS module.
+ - dma-names : named "ch%d", where %d is the channel number ranging from zero
+ to the number of channels (DnFIFOs) minus one.
Example:
usbhs: usb@e6590000 {
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index a53bd5b5..fc9b9f0 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -38,7 +38,9 @@
config PHY_DM816X_USB
tristate "TI dm816x USB PHY driver"
depends on ARCH_OMAP2PLUS
+ depends on USB_SUPPORT
select GENERIC_PHY
+ select USB_PHY
help
Enable this for dm816x USB to work.
@@ -97,8 +99,9 @@
config OMAP_USB2
tristate "OMAP USB2 PHY Driver"
depends on ARCH_OMAP2PLUS
- depends on USB_PHY
+ depends on USB_SUPPORT
select GENERIC_PHY
+ select USB_PHY
select OMAP_CONTROL_PHY
depends on OMAP_OCP2SCP
help
@@ -122,8 +125,9 @@
config TWL4030_USB
tristate "TWL4030 USB Transceiver Driver"
depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS
- depends on USB_PHY
+ depends on USB_SUPPORT
select GENERIC_PHY
+ select USB_PHY
help
Enable this to support the USB OTG transceiver on TWL4030
family chips (including the TWL5030 and TPS659x0 devices).
@@ -304,7 +308,7 @@
config PHY_QCOM_UFS
tristate "Qualcomm UFS PHY driver"
- depends on OF && ARCH_MSM
+ depends on OF && ARCH_QCOM
select GENERIC_PHY
help
Support for UFS PHY on QCOM chipsets.
diff --git a/drivers/phy/phy-core.c b/drivers/phy/phy-core.c
index 3791838..63bc12d 100644
--- a/drivers/phy/phy-core.c
+++ b/drivers/phy/phy-core.c
@@ -530,7 +530,7 @@
{
struct phy *phy = phy_get(dev, string);
- if (PTR_ERR(phy) == -ENODEV)
+ if (IS_ERR(phy) && (PTR_ERR(phy) == -ENODEV))
phy = NULL;
return phy;
@@ -584,7 +584,7 @@
{
struct phy *phy = devm_phy_get(dev, string);
- if (PTR_ERR(phy) == -ENODEV)
+ if (IS_ERR(phy) && (PTR_ERR(phy) == -ENODEV))
phy = NULL;
return phy;
diff --git a/drivers/phy/phy-omap-usb2.c b/drivers/phy/phy-omap-usb2.c
index 183ef43..c1a4686 100644
--- a/drivers/phy/phy-omap-usb2.c
+++ b/drivers/phy/phy-omap-usb2.c
@@ -275,6 +275,7 @@
phy->wkupclk = devm_clk_get(phy->dev, "usb_phy_cm_clk32k");
if (IS_ERR(phy->wkupclk)) {
dev_err(&pdev->dev, "unable to get usb_phy_cm_clk32k\n");
+ pm_runtime_disable(phy->dev);
return PTR_ERR(phy->wkupclk);
} else {
dev_warn(&pdev->dev,
diff --git a/drivers/phy/phy-rcar-gen2.c b/drivers/phy/phy-rcar-gen2.c
index 778276a..97d45f4 100644
--- a/drivers/phy/phy-rcar-gen2.c
+++ b/drivers/phy/phy-rcar-gen2.c
@@ -23,7 +23,7 @@
#define USBHS_LPSTS 0x02
#define USBHS_UGCTRL 0x80
#define USBHS_UGCTRL2 0x84
-#define USBHS_UGSTS 0x88 /* The manuals have 0x90 */
+#define USBHS_UGSTS 0x88 /* From technical update */
/* Low Power Status register (LPSTS) */
#define USBHS_LPSTS_SUSPM 0x4000
@@ -41,7 +41,7 @@
#define USBHS_UGCTRL2_USB0SEL_HS_USB 0x00000030
/* USB General status register (UGSTS) */
-#define USBHS_UGSTS_LOCK 0x00000300 /* The manuals have 0x3 */
+#define USBHS_UGSTS_LOCK 0x00000100 /* From technical update */
#define PHYS_PER_CHANNEL 2
diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
index fdab715..c0eafa6 100644
--- a/drivers/usb/dwc3/core.h
+++ b/drivers/usb/dwc3/core.h
@@ -339,7 +339,7 @@
#define DWC3_DGCMD_SET_ENDPOINT_NRDY 0x0c
#define DWC3_DGCMD_RUN_SOC_BUS_LOOPBACK 0x10
-#define DWC3_DGCMD_STATUS(n) (((n) >> 15) & 1)
+#define DWC3_DGCMD_STATUS(n) (((n) >> 12) & 0x0F)
#define DWC3_DGCMD_CMDACT (1 << 10)
#define DWC3_DGCMD_CMDIOC (1 << 8)
@@ -355,7 +355,7 @@
#define DWC3_DEPCMD_PARAM_SHIFT 16
#define DWC3_DEPCMD_PARAM(x) ((x) << DWC3_DEPCMD_PARAM_SHIFT)
#define DWC3_DEPCMD_GET_RSC_IDX(x) (((x) >> DWC3_DEPCMD_PARAM_SHIFT) & 0x7f)
-#define DWC3_DEPCMD_STATUS(x) (((x) >> 15) & 1)
+#define DWC3_DEPCMD_STATUS(x) (((x) >> 12) & 0x0F)
#define DWC3_DEPCMD_HIPRI_FORCERM (1 << 11)
#define DWC3_DEPCMD_CMDACT (1 << 10)
#define DWC3_DEPCMD_CMDIOC (1 << 8)
diff --git a/drivers/usb/gadget/function/f_fs.c b/drivers/usb/gadget/function/f_fs.c
index 6bdb570..3507f88 100644
--- a/drivers/usb/gadget/function/f_fs.c
+++ b/drivers/usb/gadget/function/f_fs.c
@@ -315,7 +315,6 @@
return ret;
}
- set_bit(FFS_FL_CALL_CLOSED_CALLBACK, &ffs->flags);
return len;
}
break;
@@ -847,7 +846,7 @@
ret = ep->status;
if (io_data->read && ret > 0) {
ret = copy_to_iter(data, ret, &io_data->data);
- if (unlikely(iov_iter_count(&io_data->data)))
+ if (!ret)
ret = -EFAULT;
}
}
@@ -1463,8 +1462,7 @@
{
ENTER();
- if (test_and_clear_bit(FFS_FL_CALL_CLOSED_CALLBACK, &ffs->flags))
- ffs_closed(ffs);
+ ffs_closed(ffs);
BUG_ON(ffs->gadget);
@@ -3422,9 +3420,13 @@
ffs_obj->desc_ready = true;
ffs_obj->ffs_data = ffs;
- if (ffs_obj->ffs_ready_callback)
+ if (ffs_obj->ffs_ready_callback) {
ret = ffs_obj->ffs_ready_callback(ffs);
+ if (ret)
+ goto done;
+ }
+ set_bit(FFS_FL_CALL_CLOSED_CALLBACK, &ffs->flags);
done:
ffs_dev_unlock();
return ret;
@@ -3443,7 +3445,8 @@
ffs_obj->desc_ready = false;
- if (ffs_obj->ffs_closed_callback)
+ if (test_and_clear_bit(FFS_FL_CALL_CLOSED_CALLBACK, &ffs->flags) &&
+ ffs_obj->ffs_closed_callback)
ffs_obj->ffs_closed_callback(ffs);
if (!ffs_obj->opts || ffs_obj->opts->no_configfs
diff --git a/drivers/usb/gadget/function/f_midi.c b/drivers/usb/gadget/function/f_midi.c
index 259b656..6316aa5 100644
--- a/drivers/usb/gadget/function/f_midi.c
+++ b/drivers/usb/gadget/function/f_midi.c
@@ -973,7 +973,13 @@
int result;
mutex_lock(&opts->lock);
- result = strlcpy(page, opts->id, PAGE_SIZE);
+ if (opts->id) {
+ result = strlcpy(page, opts->id, PAGE_SIZE);
+ } else {
+ page[0] = 0;
+ result = 0;
+ }
+
mutex_unlock(&opts->lock);
return result;
diff --git a/drivers/usb/gadget/function/f_uac1.c b/drivers/usb/gadget/function/f_uac1.c
index 9719abf..7856b33 100644
--- a/drivers/usb/gadget/function/f_uac1.c
+++ b/drivers/usb/gadget/function/f_uac1.c
@@ -588,7 +588,10 @@
if (intf == 1) {
if (alt == 1) {
- config_ep_by_speed(cdev->gadget, f, out_ep);
+ err = config_ep_by_speed(cdev->gadget, f, out_ep);
+ if (err)
+ return err;
+
usb_ep_enable(out_ep);
out_ep->driver_data = audio;
audio->copy_buf = f_audio_buffer_alloc(audio_buf_size);
diff --git a/drivers/usb/gadget/legacy/g_ffs.c b/drivers/usb/gadget/legacy/g_ffs.c
index 7b9ef7e..e821931 100644
--- a/drivers/usb/gadget/legacy/g_ffs.c
+++ b/drivers/usb/gadget/legacy/g_ffs.c
@@ -304,8 +304,10 @@
gfs_registered = true;
ret = usb_composite_probe(&gfs_driver);
- if (unlikely(ret < 0))
+ if (unlikely(ret < 0)) {
+ ++missing_funcs;
gfs_registered = false;
+ }
return ret;
}
diff --git a/drivers/usb/gadget/udc/s3c2410_udc.c b/drivers/usb/gadget/udc/s3c2410_udc.c
index b808951..99fd9a5 100644
--- a/drivers/usb/gadget/udc/s3c2410_udc.c
+++ b/drivers/usb/gadget/udc/s3c2410_udc.c
@@ -1487,7 +1487,7 @@
dprintk(DEBUG_NORMAL, "%s()\n", __func__);
- s3c2410_udc_set_pullup(udc, is_on ? 0 : 1);
+ s3c2410_udc_set_pullup(udc, is_on);
return 0;
}
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index ec8ac16..36bf089b 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -3682,18 +3682,21 @@
{
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
unsigned long flags;
- int ret;
+ int ret, slot_id;
struct xhci_command *command;
command = xhci_alloc_command(xhci, false, false, GFP_KERNEL);
if (!command)
return 0;
+ /* xhci->slot_id and xhci->addr_dev are not thread-safe */
+ mutex_lock(&xhci->mutex);
spin_lock_irqsave(&xhci->lock, flags);
command->completion = &xhci->addr_dev;
ret = xhci_queue_slot_control(xhci, command, TRB_ENABLE_SLOT, 0);
if (ret) {
spin_unlock_irqrestore(&xhci->lock, flags);
+ mutex_unlock(&xhci->mutex);
xhci_dbg(xhci, "FIXME: allocate a command ring segment\n");
kfree(command);
return 0;
@@ -3702,8 +3705,10 @@
spin_unlock_irqrestore(&xhci->lock, flags);
wait_for_completion(command->completion);
+ slot_id = xhci->slot_id;
+ mutex_unlock(&xhci->mutex);
- if (!xhci->slot_id || command->status != COMP_SUCCESS) {
+ if (!slot_id || command->status != COMP_SUCCESS) {
xhci_err(xhci, "Error while assigning device slot ID\n");
xhci_err(xhci, "Max number of devices this xHCI host supports is %u.\n",
HCS_MAX_SLOTS(
@@ -3728,11 +3733,11 @@
* xhci_discover_or_reset_device(), which may be called as part of
* mass storage driver error handling.
*/
- if (!xhci_alloc_virt_device(xhci, xhci->slot_id, udev, GFP_NOIO)) {
+ if (!xhci_alloc_virt_device(xhci, slot_id, udev, GFP_NOIO)) {
xhci_warn(xhci, "Could not allocate xHCI USB device data structures\n");
goto disable_slot;
}
- udev->slot_id = xhci->slot_id;
+ udev->slot_id = slot_id;
#ifndef CONFIG_USB_DEFAULT_PERSIST
/*
@@ -3778,12 +3783,15 @@
struct xhci_slot_ctx *slot_ctx;
struct xhci_input_control_ctx *ctrl_ctx;
u64 temp_64;
- struct xhci_command *command;
+ struct xhci_command *command = NULL;
+
+ mutex_lock(&xhci->mutex);
if (!udev->slot_id) {
xhci_dbg_trace(xhci, trace_xhci_dbg_address,
"Bad Slot ID %d", udev->slot_id);
- return -EINVAL;
+ ret = -EINVAL;
+ goto out;
}
virt_dev = xhci->devs[udev->slot_id];
@@ -3796,7 +3804,8 @@
*/
xhci_warn(xhci, "Virt dev invalid for slot_id 0x%x!\n",
udev->slot_id);
- return -EINVAL;
+ ret = -EINVAL;
+ goto out;
}
if (setup == SETUP_CONTEXT_ONLY) {
@@ -3804,13 +3813,15 @@
if (GET_SLOT_STATE(le32_to_cpu(slot_ctx->dev_state)) ==
SLOT_STATE_DEFAULT) {
xhci_dbg(xhci, "Slot already in default state\n");
- return 0;
+ goto out;
}
}
command = xhci_alloc_command(xhci, false, false, GFP_KERNEL);
- if (!command)
- return -ENOMEM;
+ if (!command) {
+ ret = -ENOMEM;
+ goto out;
+ }
command->in_ctx = virt_dev->in_ctx;
command->completion = &xhci->addr_dev;
@@ -3820,8 +3831,8 @@
if (!ctrl_ctx) {
xhci_warn(xhci, "%s: Could not get input context, bad type.\n",
__func__);
- kfree(command);
- return -EINVAL;
+ ret = -EINVAL;
+ goto out;
}
/*
* If this is the first Set Address since device plug-in or
@@ -3848,8 +3859,7 @@
spin_unlock_irqrestore(&xhci->lock, flags);
xhci_dbg_trace(xhci, trace_xhci_dbg_address,
"FIXME: allocate a command ring segment");
- kfree(command);
- return ret;
+ goto out;
}
xhci_ring_cmd_db(xhci);
spin_unlock_irqrestore(&xhci->lock, flags);
@@ -3896,10 +3906,8 @@
ret = -EINVAL;
break;
}
- if (ret) {
- kfree(command);
- return ret;
- }
+ if (ret)
+ goto out;
temp_64 = xhci_read_64(xhci, &xhci->op_regs->dcbaa_ptr);
xhci_dbg_trace(xhci, trace_xhci_dbg_address,
"Op regs DCBAA ptr = %#016llx", temp_64);
@@ -3932,8 +3940,10 @@
xhci_dbg_trace(xhci, trace_xhci_dbg_address,
"Internal device address = %d",
le32_to_cpu(slot_ctx->dev_state) & DEV_ADDR_MASK);
+out:
+ mutex_unlock(&xhci->mutex);
kfree(command);
- return 0;
+ return ret;
}
int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev)
@@ -4855,6 +4865,7 @@
return 0;
}
+ mutex_init(&xhci->mutex);
xhci->cap_regs = hcd->regs;
xhci->op_regs = hcd->regs +
HC_LENGTH(readl(&xhci->cap_regs->hc_capbase));
@@ -5011,4 +5022,12 @@
BUILD_BUG_ON(sizeof(struct xhci_run_regs) != (8+8*128)*32/8);
return 0;
}
+
+/*
+ * If an init function is provided, an exit function must also be provided
+ * to allow module unload.
+ */
+static void __exit xhci_hcd_fini(void) { }
+
module_init(xhci_hcd_init);
+module_exit(xhci_hcd_fini);
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index ea75e8c..6977f84 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -1497,6 +1497,8 @@
struct list_head lpm_failed_devs;
/* slot enabling and address device helpers */
+ /* these are not thread safe so use mutex */
+ struct mutex mutex;
struct completion addr_dev;
int slot_id;
/* For USB 3.0 LPM enable/disable. */
diff --git a/drivers/usb/musb/musb_core.c b/drivers/usb/musb/musb_core.c
index 3789b08..6dca3d7 100644
--- a/drivers/usb/musb/musb_core.c
+++ b/drivers/usb/musb/musb_core.c
@@ -2021,13 +2021,7 @@
if (musb->ops->quirks)
musb->io.quirks = musb->ops->quirks;
- /* At least tusb6010 has it's own offsets.. */
- if (musb->ops->ep_offset)
- musb->io.ep_offset = musb->ops->ep_offset;
- if (musb->ops->ep_select)
- musb->io.ep_select = musb->ops->ep_select;
-
- /* ..and some devices use indexed offset or flat offset */
+ /* Most devices use indexed offset or flat offset */
if (musb->io.quirks & MUSB_INDEXED_EP) {
musb->io.ep_offset = musb_indexed_ep_offset;
musb->io.ep_select = musb_indexed_ep_select;
@@ -2036,6 +2030,12 @@
musb->io.ep_select = musb_flat_ep_select;
}
+ /* At least tusb6010 has its own offsets */
+ if (musb->ops->ep_offset)
+ musb->io.ep_offset = musb->ops->ep_offset;
+ if (musb->ops->ep_select)
+ musb->io.ep_select = musb->ops->ep_select;
+
if (musb->ops->fifo_mode)
fifo_mode = musb->ops->fifo_mode;
else
diff --git a/drivers/usb/phy/phy-ab8500-usb.c b/drivers/usb/phy/phy-ab8500-usb.c
index 7225d52..03ab0c6 100644
--- a/drivers/usb/phy/phy-ab8500-usb.c
+++ b/drivers/usb/phy/phy-ab8500-usb.c
@@ -1179,7 +1179,7 @@
}
err = devm_request_threaded_irq(&pdev->dev, irq, NULL,
ab8500_usb_link_status_irq,
- IRQF_NO_SUSPEND | IRQF_SHARED,
+ IRQF_NO_SUSPEND | IRQF_SHARED | IRQF_ONESHOT,
"usb-link-status", ab);
if (err < 0) {
dev_err(ab->dev, "request_irq failed for link status irq\n");
@@ -1195,7 +1195,7 @@
}
err = devm_request_threaded_irq(&pdev->dev, irq, NULL,
ab8500_usb_disconnect_irq,
- IRQF_NO_SUSPEND | IRQF_SHARED,
+ IRQF_NO_SUSPEND | IRQF_SHARED | IRQF_ONESHOT,
"usb-id-fall", ab);
if (err < 0) {
dev_err(ab->dev, "request_irq failed for ID fall irq\n");
@@ -1211,7 +1211,7 @@
}
err = devm_request_threaded_irq(&pdev->dev, irq, NULL,
ab8500_usb_disconnect_irq,
- IRQF_NO_SUSPEND | IRQF_SHARED,
+ IRQF_NO_SUSPEND | IRQF_SHARED | IRQF_ONESHOT,
"usb-vbus-fall", ab);
if (err < 0) {
dev_err(ab->dev, "request_irq failed for Vbus fall irq\n");
diff --git a/drivers/usb/phy/phy-tahvo.c b/drivers/usb/phy/phy-tahvo.c
index 845f658..2b28443 100644
--- a/drivers/usb/phy/phy-tahvo.c
+++ b/drivers/usb/phy/phy-tahvo.c
@@ -401,7 +401,8 @@
dev_set_drvdata(&pdev->dev, tu);
tu->irq = platform_get_irq(pdev, 0);
- ret = request_threaded_irq(tu->irq, NULL, tahvo_usb_vbus_interrupt, 0,
+ ret = request_threaded_irq(tu->irq, NULL, tahvo_usb_vbus_interrupt,
+ IRQF_ONESHOT,
"tahvo-vbus", tu);
if (ret) {
dev_err(&pdev->dev, "could not register tahvo-vbus irq: %d\n",
diff --git a/drivers/usb/renesas_usbhs/fifo.c b/drivers/usb/renesas_usbhs/fifo.c
index 8597cf9..c0f5c65 100644
--- a/drivers/usb/renesas_usbhs/fifo.c
+++ b/drivers/usb/renesas_usbhs/fifo.c
@@ -611,6 +611,8 @@
static int usbhsf_prepare_pop(struct usbhs_pkt *pkt, int *is_done)
{
struct usbhs_pipe *pipe = pkt->pipe;
+ struct usbhs_priv *priv = usbhs_pipe_to_priv(pipe);
+ struct usbhs_fifo *fifo = usbhsf_get_cfifo(priv);
if (usbhs_pipe_is_busy(pipe))
return 0;
@@ -624,6 +626,9 @@
usbhs_pipe_data_sequence(pipe, pkt->sequence);
pkt->sequence = -1; /* -1 sequence will be ignored */
+ if (usbhs_pipe_is_dcp(pipe))
+ usbhsf_fifo_clear(pipe, fifo);
+
usbhs_pipe_set_trans_count_if_bulk(pipe, pkt->length);
usbhs_pipe_enable(pipe);
usbhs_pipe_running(pipe, 1);
@@ -673,7 +678,14 @@
*is_done = 1;
usbhsf_rx_irq_ctrl(pipe, 0);
usbhs_pipe_running(pipe, 0);
- usbhs_pipe_disable(pipe); /* disable pipe first */
+ /*
+ * If function mode, since this controller is possible to enter
+ * Control Write status stage at this timing, this driver
+ * should not disable the pipe. If such a case happens, this
+ * controller is not able to complete the status stage.
+ */
+ if (!usbhs_mod_is_host(priv) && !usbhs_pipe_is_dcp(pipe))
+ usbhs_pipe_disable(pipe); /* disable pipe first */
}
/*
@@ -1227,15 +1239,21 @@
{
char name[16];
- snprintf(name, sizeof(name), "tx%d", channel);
- fifo->tx_chan = dma_request_slave_channel_reason(dev, name);
- if (IS_ERR(fifo->tx_chan))
- fifo->tx_chan = NULL;
-
- snprintf(name, sizeof(name), "rx%d", channel);
- fifo->rx_chan = dma_request_slave_channel_reason(dev, name);
- if (IS_ERR(fifo->rx_chan))
- fifo->rx_chan = NULL;
+ /*
+ * To avoid complex handing for DnFIFOs, the driver uses each
+ * DnFIFO as TX or RX direction (not bi-direction).
+ * So, the driver uses odd channels for TX, even channels for RX.
+ */
+ snprintf(name, sizeof(name), "ch%d", channel);
+ if (channel & 1) {
+ fifo->tx_chan = dma_request_slave_channel_reason(dev, name);
+ if (IS_ERR(fifo->tx_chan))
+ fifo->tx_chan = NULL;
+ } else {
+ fifo->rx_chan = dma_request_slave_channel_reason(dev, name);
+ if (IS_ERR(fifo->rx_chan))
+ fifo->rx_chan = NULL;
+ }
}
static void usbhsf_dma_init(struct usbhs_priv *priv, struct usbhs_fifo *fifo,
diff --git a/drivers/usb/serial/cp210x.c b/drivers/usb/serial/cp210x.c
index 9031750..ffd739e 100644
--- a/drivers/usb/serial/cp210x.c
+++ b/drivers/usb/serial/cp210x.c
@@ -128,6 +128,7 @@
{ USB_DEVICE(0x10C4, 0x8946) }, /* Ketra N1 Wireless Interface */
{ USB_DEVICE(0x10C4, 0x8977) }, /* CEL MeshWorks DevKit Device */
{ USB_DEVICE(0x10C4, 0x8998) }, /* KCF Technologies PRN */
+ { USB_DEVICE(0x10C4, 0x8A2A) }, /* HubZ dual ZigBee and Z-Wave dongle */
{ USB_DEVICE(0x10C4, 0xEA60) }, /* Silicon Labs factory default */
{ USB_DEVICE(0x10C4, 0xEA61) }, /* Silicon Labs factory default */
{ USB_DEVICE(0x10C4, 0xEA70) }, /* Silicon Labs factory default */
diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index 8eb68a3..4c8b3b8 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -699,6 +699,7 @@
{ USB_DEVICE(XSENS_VID, XSENS_AWINDA_DONGLE_PID) },
{ USB_DEVICE(XSENS_VID, XSENS_AWINDA_STATION_PID) },
{ USB_DEVICE(XSENS_VID, XSENS_CONVERTER_PID) },
+ { USB_DEVICE(XSENS_VID, XSENS_MTDEVBOARD_PID) },
{ USB_DEVICE(XSENS_VID, XSENS_MTW_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_OMNI1509) },
{ USB_DEVICE(MOBILITY_VID, MOBILITY_USB_SERIAL_PID) },
diff --git a/drivers/usb/serial/ftdi_sio_ids.h b/drivers/usb/serial/ftdi_sio_ids.h
index 4e4f46f..792e054 100644
--- a/drivers/usb/serial/ftdi_sio_ids.h
+++ b/drivers/usb/serial/ftdi_sio_ids.h
@@ -155,6 +155,7 @@
#define XSENS_AWINDA_STATION_PID 0x0101
#define XSENS_AWINDA_DONGLE_PID 0x0102
#define XSENS_MTW_PID 0x0200 /* Xsens MTw */
+#define XSENS_MTDEVBOARD_PID 0x0300 /* Motion Tracker Development Board */
#define XSENS_CONVERTER_PID 0xD00D /* Xsens USB-serial converter */
/* Xsens devices using FTDI VID */