powerpc/83xx: Add USB Host/Gadget support for MPC8360E-MDS boards
- Update the device tree per QE USB bindings;
- Add timer (FSL GTM) node;
- Add gpio-controller node for BCSR13 bank (GPIOs on that bank
are used to control the USB transceiver);
- Set up other BCSR registers;
- Configure the QE Par IO.
The work is loosely based on Li Yang's patch[1], which was used
to support peripheral mode only.
[1] http://ozlabs.org/pipermail/linuxppc-dev/2008-August/061357.html
The s-o-b line of the original patch preserved here.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
diff --git a/arch/powerpc/boot/dts/mpc836x_mds.dts b/arch/powerpc/boot/dts/mpc836x_mds.dts
index 14534d0..6e34f17 100644
--- a/arch/powerpc/boot/dts/mpc836x_mds.dts
+++ b/arch/powerpc/boot/dts/mpc836x_mds.dts
@@ -69,8 +69,18 @@
};
bcsr@1,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
compatible = "fsl,mpc8360mds-bcsr";
reg = <1 0 0x8000>;
+ ranges = <0 1 0 0x8000>;
+
+ bcsr13: gpio-controller@d {
+ #gpio-cells = <2>;
+ compatible = "fsl,mpc8360mds-bcsr-gpio";
+ reg = <0xd 1>;
+ gpio-controller;
+ };
};
};
@@ -195,10 +205,21 @@
};
par_io@1400 {
+ #address-cells = <1>;
+ #size-cells = <1>;
reg = <0x1400 0x100>;
+ ranges = <0 0x1400 0x100>;
device_type = "par_io";
num-ports = <7>;
+ qe_pio_b: gpio-controller@18 {
+ #gpio-cells = <2>;
+ compatible = "fsl,mpc8360-qe-pario-bank",
+ "fsl,mpc8323-qe-pario-bank";
+ reg = <0x18 0x18>;
+ gpio-controller;
+ };
+
pio1: ucc_pin@01 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
@@ -282,6 +303,15 @@
};
};
+ timer@440 {
+ compatible = "fsl,mpc8360-qe-gtm",
+ "fsl,qe-gtm", "fsl,gtm";
+ reg = <0x440 0x40>;
+ clock-frequency = <132000000>;
+ interrupts = <12 13 14 15>;
+ interrupt-parent = <&qeic>;
+ };
+
spi@4c0 {
cell-index = <0>;
compatible = "fsl,spi";
@@ -301,11 +331,20 @@
};
usb@6c0 {
- compatible = "qe_udc";
+ compatible = "fsl,mpc8360-qe-usb",
+ "fsl,mpc8323-qe-usb";
reg = <0x6c0 0x40 0x8b00 0x100>;
interrupts = <11>;
interrupt-parent = <&qeic>;
- mode = "slave";
+ fsl,fullspeed-clock = "clk21";
+ fsl,lowspeed-clock = "brg9";
+ gpios = <&qe_pio_b 2 0 /* USBOE */
+ &qe_pio_b 3 0 /* USBTP */
+ &qe_pio_b 8 0 /* USBTN */
+ &qe_pio_b 9 0 /* USBRP */
+ &qe_pio_b 11 0 /* USBRN */
+ &bcsr13 5 0 /* SPEED */
+ &bcsr13 4 1>; /* POWER */
};
enet0: ucc@2000 {