V4L/DVB (9037): Fix support for Hauppauge Nova-S SE
Different backends have different input busses (saa7146, flexcop).
To reflect that a config-option to the s5h1420-driver was added which makes
the output mode selectable.
Furthermore the s5h1420-driver is now doing the same i2c-method as it was done
before adding support for other i2c-users.
This patch needs to go into the current release of the kernel, as this driver
is currently broken.
(Thanks to Eberhard Kaltenhaeuser for helping out to debug this issue.)
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
diff --git a/drivers/media/dvb/b2c2/flexcop-fe-tuner.c b/drivers/media/dvb/b2c2/flexcop-fe-tuner.c
index 4eed783..a127a41 100644
--- a/drivers/media/dvb/b2c2/flexcop-fe-tuner.c
+++ b/drivers/media/dvb/b2c2/flexcop-fe-tuner.c
@@ -491,6 +491,7 @@
.demod_address = 0x53,
.invert = 1,
.repeated_start_workaround = 1,
+ .serial_mpeg = 1,
};
static struct itd1000_config skystar2_rev2_7_itd1000_config = {
diff --git a/drivers/media/dvb/frontends/s5h1420.c b/drivers/media/dvb/frontends/s5h1420.c
index 747d3fa..7d6cb39 100644
--- a/drivers/media/dvb/frontends/s5h1420.c
+++ b/drivers/media/dvb/frontends/s5h1420.c
@@ -94,8 +94,11 @@
if (ret != 3)
return ret;
} else {
- ret = i2c_transfer(state->i2c, &msg[1], 2);
- if (ret != 2)
+ ret = i2c_transfer(state->i2c, &msg[1], 1);
+ if (ret != 1)
+ return ret;
+ ret = i2c_transfer(state->i2c, &msg[2], 1);
+ if (ret != 1)
return ret;
}
@@ -823,7 +826,7 @@
struct s5h1420_state* state = fe->demodulator_priv;
/* disable power down and do reset */
- state->CON_1_val = 0x10;
+ state->CON_1_val = state->config->serial_mpeg << 4;
s5h1420_writereg(state, 0x02, state->CON_1_val);
msleep(10);
s5h1420_reset(state);
diff --git a/drivers/media/dvb/frontends/s5h1420.h b/drivers/media/dvb/frontends/s5h1420.h
index 4c913f1..ff30813 100644
--- a/drivers/media/dvb/frontends/s5h1420.h
+++ b/drivers/media/dvb/frontends/s5h1420.h
@@ -32,10 +32,12 @@
u8 demod_address;
/* does the inversion require inversion? */
- u8 invert : 1;
+ u8 invert:1;
- u8 repeated_start_workaround : 1;
- u8 cdclk_polarity : 1; /* 1 == falling edge, 0 == raising edge */
+ u8 repeated_start_workaround:1;
+ u8 cdclk_polarity:1; /* 1 == falling edge, 0 == raising edge */
+
+ u8 serial_mpeg:1;
};
#if defined(CONFIG_DVB_S5H1420) || (defined(CONFIG_DVB_S5H1420_MODULE) && defined(MODULE))