mtd: spi-nor: add support for flag status register on Micron chips
Some new Micron flash chips require reading the flag status register to
determine when operations have completed.
Furthermore, chips with multi-die stacks of the 65nm 256Mb QSPI also
require reading the status register before reading the flag status
register.
This patch adds support for the flag status register in the n25q512ax3
and n25q00 Micron QSPI flash chips.
Signed-off-by: Graham Moore <grmoore@altera.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
index c713c86..7da3a70 100644
--- a/drivers/mtd/spi-nor/spi-nor.c
+++ b/drivers/mtd/spi-nor/spi-nor.c
@@ -48,6 +48,25 @@
}
/*
+ * Read the flag status register, returning its value in the location
+ * Return the status register value.
+ * Returns negative if error occurred.
+ */
+static int read_fsr(struct spi_nor *nor)
+{
+ int ret;
+ u8 val;
+
+ ret = nor->read_reg(nor, SPINOR_OP_RDFSR, &val, 1);
+ if (ret < 0) {
+ pr_err("error %d reading FSR\n", ret);
+ return ret;
+ }
+
+ return val;
+}
+
+/*
* Read configuration register, returning its value in the
* location. Return the configuration register value.
* Returns negative if error occured.
@@ -165,6 +184,32 @@
return -ETIMEDOUT;
}
+static int spi_nor_wait_till_fsr_ready(struct spi_nor *nor)
+{
+ unsigned long deadline;
+ int sr;
+ int fsr;
+
+ deadline = jiffies + MAX_READY_WAIT_JIFFIES;
+
+ do {
+ cond_resched();
+
+ sr = read_sr(nor);
+ if (sr < 0) {
+ break;
+ } else if (!(sr & SR_WIP)) {
+ fsr = read_fsr(nor);
+ if (fsr < 0)
+ break;
+ if (fsr & FSR_READY)
+ return 0;
+ }
+ } while (!time_after_eq(jiffies, deadline));
+
+ return -ETIMEDOUT;
+}
+
/*
* Service routine to read status register until ready, or timeout occurs.
* Returns non-zero if error.
@@ -402,6 +447,7 @@
#define SECT_4K_PMC 0x10 /* SPINOR_OP_BE_4K_PMC works uniformly */
#define SPI_NOR_DUAL_READ 0x20 /* Flash supports Dual Read */
#define SPI_NOR_QUAD_READ 0x40 /* Flash supports Quad Read */
+#define USE_FSR 0x80 /* use flag status register */
};
#define INFO(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \
@@ -488,6 +534,8 @@
{ "n25q128a13", INFO(0x20ba18, 0, 64 * 1024, 256, 0) },
{ "n25q256a", INFO(0x20ba19, 0, 64 * 1024, 512, SECT_4K) },
{ "n25q512a", INFO(0x20bb20, 0, 64 * 1024, 1024, SECT_4K) },
+ { "n25q512ax3", INFO(0x20ba20, 0, 64 * 1024, 1024, USE_FSR) },
+ { "n25q00", INFO(0x20ba21, 0, 64 * 1024, 2048, USE_FSR) },
/* PMC */
{ "pm25lv512", INFO(0, 0, 32 * 1024, 2, SECT_4K_PMC) },
@@ -965,6 +1013,10 @@
else
mtd->_write = spi_nor_write;
+ if ((info->flags & USE_FSR) &&
+ nor->wait_till_ready == spi_nor_wait_till_ready)
+ nor->wait_till_ready = spi_nor_wait_till_fsr_ready;
+
/* prefer "small sector" erase if possible */
if (info->flags & SECT_4K) {
nor->erase_opcode = SPINOR_OP_BE_4K;
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
index 5324184..9e6294f 100644
--- a/include/linux/mtd/spi-nor.h
+++ b/include/linux/mtd/spi-nor.h
@@ -34,6 +34,7 @@
#define SPINOR_OP_SE 0xd8 /* Sector erase (usually 64KiB) */
#define SPINOR_OP_RDID 0x9f /* Read JEDEC ID */
#define SPINOR_OP_RDCR 0x35 /* Read configuration register */
+#define SPINOR_OP_RDFSR 0x70 /* Read flag status register */
/* 4-byte address opcodes - used on Spansion and some Macronix flashes. */
#define SPINOR_OP_READ4 0x13 /* Read data bytes (low frequency) */
@@ -66,6 +67,9 @@
#define SR_QUAD_EN_MX 0x40 /* Macronix Quad I/O */
+/* Flag Status Register bits */
+#define FSR_READY 0x80
+
/* Configuration Register bits. */
#define CR_QUAD_EN_SPAN 0x2 /* Spansion Quad I/O */