RM9000 serial driver
Add support for the integrated serial ports of the MIPS RM9122 processor
and its relatives.
The patch also does some whitespace cleanup.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c
index 194362d..c9832d9 100644
--- a/drivers/serial/8250.c
+++ b/drivers/serial/8250.c
@@ -251,9 +251,16 @@
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
.flags = UART_CAP_FIFO | UART_CAP_UUE,
},
+ [PORT_RM9000] = {
+ .name = "RM9000",
+ .fifo_size = 16,
+ .tx_loadsz = 16,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+ .flags = UART_CAP_FIFO,
+ },
};
-#ifdef CONFIG_SERIAL_8250_AU1X00
+#if defined (CONFIG_SERIAL_8250_AU1X00)
/* Au1x00 UART hardware has a weird register layout */
static const u8 au_io_in_map[] = {
@@ -289,6 +296,44 @@
return au_io_out_map[offset];
}
+#elif defined (CONFIG_SERIAL_8250_RM9K)
+
+static const u8
+ regmap_in[8] = {
+ [UART_RX] = 0x00,
+ [UART_IER] = 0x0c,
+ [UART_IIR] = 0x14,
+ [UART_LCR] = 0x1c,
+ [UART_MCR] = 0x20,
+ [UART_LSR] = 0x24,
+ [UART_MSR] = 0x28,
+ [UART_SCR] = 0x2c
+ },
+ regmap_out[8] = {
+ [UART_TX] = 0x04,
+ [UART_IER] = 0x0c,
+ [UART_FCR] = 0x18,
+ [UART_LCR] = 0x1c,
+ [UART_MCR] = 0x20,
+ [UART_LSR] = 0x24,
+ [UART_MSR] = 0x28,
+ [UART_SCR] = 0x2c
+ };
+
+static inline int map_8250_in_reg(struct uart_8250_port *up, int offset)
+{
+ if (up->port.iotype != UPIO_RM9000)
+ return offset;
+ return regmap_in[offset];
+}
+
+static inline int map_8250_out_reg(struct uart_8250_port *up, int offset)
+{
+ if (up->port.iotype != UPIO_RM9000)
+ return offset;
+ return regmap_out[offset];
+}
+
#else
/* sane hardware needs no mapping */
@@ -311,6 +356,7 @@
case UPIO_DWAPB:
return readb(up->port.membase + offset);
+ case UPIO_RM9000:
case UPIO_MEM32:
return readl(up->port.membase + offset);
@@ -348,6 +394,7 @@
writeb(value, up->port.membase + offset);
break;
+ case UPIO_RM9000:
case UPIO_MEM32:
writel(value, up->port.membase + offset);
break;
@@ -419,7 +466,7 @@
serial_outp(up, UART_DLM, value >> 8 & 0xff);
}
-#ifdef CONFIG_SERIAL_8250_AU1X00
+#if defined (CONFIG_SERIAL_8250_AU1X00)
/* Au1x00 haven't got a standard divisor latch */
static int serial_dl_read(struct uart_8250_port *up)
{
@@ -436,6 +483,24 @@
else
_serial_dl_write(up, value);
}
+#elif defined (CONFIG_SERIAL_8250_RM9K)
+static int serial_dl_read(struct uart_8250_port *up)
+{
+ return (up->port.iotype == UPIO_RM9000) ?
+ (((__raw_readl(up->port.membase + 0x10) << 8) |
+ (__raw_readl(up->port.membase + 0x08) & 0xff)) & 0xffff) :
+ _serial_dl_read(up);
+}
+
+static void serial_dl_write(struct uart_8250_port *up, int value)
+{
+ if (up->port.iotype == UPIO_RM9000) {
+ __raw_writel(value, up->port.membase + 0x08);
+ __raw_writel(value >> 8, up->port.membase + 0x10);
+ } else {
+ _serial_dl_write(up, value);
+ }
+}
#else
#define serial_dl_read(up) _serial_dl_read(up)
#define serial_dl_write(up, value) _serial_dl_write(up, value)
@@ -637,7 +702,7 @@
* its clones. (We treat the broken original StarTech 16650 V1 as a
* 16550, and why not? Startech doesn't seem to even acknowledge its
* existence.)
- *
+ *
* What evil have men's minds wrought...
*/
static void autoconfig_has_efr(struct uart_8250_port *up)
@@ -690,7 +755,7 @@
up->bugs |= UART_BUG_QUOT;
return;
}
-
+
/*
* We check for a XR16C850 by setting DLL and DLM to 0, and then
* reading back DLL and DLM. The chip type depends on the DLM
@@ -833,7 +898,7 @@
status1 &= ~0xB0; /* Disable LOCK, mask out PRESL[01] */
status1 |= 0x10; /* 1.625 divisor for baud_base --> 921600 */
serial_outp(up, 0x04, status1);
-
+
serial_dl_write(up, quot);
serial_outp(up, UART_LCR, 0);
@@ -938,7 +1003,7 @@
/*
* Do a simple existence test first; if we fail this,
* there's no point trying anything else.
- *
+ *
* 0x80 is used as a nonsense port to prevent against
* false positives due to ISA bus float. The
* assumption is that 0x80 is a non-existent port;
@@ -977,7 +1042,7 @@
save_mcr = serial_in(up, UART_MCR);
save_lcr = serial_in(up, UART_LCR);
- /*
+ /*
* Check to see if a UART is really there. Certain broken
* internal modems based on the Rockwell chipset fail this
* test, because they apparently don't implement the loopback
@@ -1084,7 +1149,7 @@
else
serial_outp(up, UART_IER, 0);
- out:
+ out:
spin_unlock_irqrestore(&up->port.lock, flags);
// restore_flags(flags);
DEBUG_AUTOCONF("type=%s\n", uart_config[up->port.type].name);
@@ -1110,7 +1175,7 @@
save_mcr = serial_inp(up, UART_MCR);
save_ier = serial_inp(up, UART_IER);
serial_outp(up, UART_MCR, UART_MCR_OUT1 | UART_MCR_OUT2);
-
+
irqs = probe_irq_on();
serial_outp(up, UART_MCR, 0);
udelay (10);
@@ -1175,8 +1240,11 @@
if (up->bugs & UART_BUG_TXEN) {
unsigned char lsr, iir;
lsr = serial_in(up, UART_LSR);
- iir = serial_in(up, UART_IIR);
- if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT)
+ iir = serial_in(up, UART_IIR) & 0x0f;
+ if ((up->port.type == PORT_RM9000) ?
+ (lsr & UART_LSR_THRE &&
+ (iir == UART_IIR_NO_INT || iir == UART_IIR_THRI)) :
+ (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT))
transmit_chars(up);
}
}
@@ -1957,7 +2025,7 @@
/*
* Ask the core to calculate the divisor for us.
*/
- baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
+ baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
quot = serial8250_get_divisor(port, baud);
/*