ARM: zynq: Allow UART1 to be used as DEBUG_LL console.
The main UART on the Xilinx ZC702 board is UART1, located at address
e0001000. Add a Kconfig option to select this device as the low-level
debugging port. This allows the really early boot printouts to reach
the USB serial adaptor on this board.
For consistency's sake, add a choice entry for UART0 even though it is
the the default if UART1 is not selected.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Tested-by: Josh Cartwright <josh.cartwright@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index b0f3857..7754d51 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -132,6 +132,23 @@
their output to UART1 serial port on DaVinci TNETV107X
devices.
+ config DEBUG_ZYNQ_UART0
+ bool "Kernel low-level debugging on Xilinx Zynq using UART0"
+ depends on ARCH_ZYNQ
+ help
+ Say Y here if you want the debug print routines to direct
+ their output to UART0 on the Zynq platform.
+
+ config DEBUG_ZYNQ_UART1
+ bool "Kernel low-level debugging on Xilinx Zynq using UART1"
+ depends on ARCH_ZYNQ
+ help
+ Say Y here if you want the debug print routines to direct
+ their output to UART1 on the Zynq platform.
+
+ If you have a ZC702 board and want early boot messages to
+ appear on the USB serial adaptor, select this option.
+
config DEBUG_DC21285_PORT
bool "Kernel low-level debugging messages via footbridge serial port"
depends on FOOTBRIDGE
diff --git a/arch/arm/mach-zynq/common.c b/arch/arm/mach-zynq/common.c
index 6f058258..f0eef84 100644
--- a/arch/arm/mach-zynq/common.c
+++ b/arch/arm/mach-zynq/common.c
@@ -85,9 +85,9 @@
#ifdef CONFIG_DEBUG_LL
{
- .virtual = UART0_VIRT,
- .pfn = __phys_to_pfn(UART0_PHYS),
- .length = UART0_SIZE,
+ .virtual = LL_UART_VADDR,
+ .pfn = __phys_to_pfn(LL_UART_PADDR),
+ .length = UART_SIZE,
.type = MT_DEVICE,
},
#endif
diff --git a/arch/arm/mach-zynq/include/mach/zynq_soc.h b/arch/arm/mach-zynq/include/mach/zynq_soc.h
index 1b8bf0e..5ebbd8e 100644
--- a/arch/arm/mach-zynq/include/mach/zynq_soc.h
+++ b/arch/arm/mach-zynq/include/mach/zynq_soc.h
@@ -25,8 +25,9 @@
* address that is known to work.
*/
#define UART0_PHYS 0xE0000000
-#define UART0_SIZE SZ_4K
-#define UART0_VIRT 0xF0001000
+#define UART1_PHYS 0xE0001000
+#define UART_SIZE SZ_4K
+#define UART_VIRT 0xF0001000
#define TTC0_PHYS 0xF8001000
#define TTC0_SIZE SZ_4K
@@ -36,12 +37,17 @@
#define SCU_PERIPH_SIZE SZ_8K
#define SCU_PERIPH_VIRT (TTC0_VIRT - SCU_PERIPH_SIZE)
+#if IS_ENABLED(CONFIG_DEBUG_ZYNQ_UART1)
+# define LL_UART_PADDR UART1_PHYS
+#else
+# define LL_UART_PADDR UART0_PHYS
+#endif
+
+#define LL_UART_VADDR UART_VIRT
+
/* The following are intended for the devices that are mapped early */
#define TTC0_BASE IOMEM(TTC0_VIRT)
#define SCU_PERIPH_BASE IOMEM(SCU_PERIPH_VIRT)
-#define LL_UART_PADDR UART0_PHYS
-#define LL_UART_VADDR UART0_VIRT
-
#endif