8139*/atp/r8169/sc92031: Move the Realtek drivers
Move the Realtek drivers into drivers/net/ethernet/realtek/ and make
the necessary Kconfig and Makefile changes.
CC: Realtek linux nic maintainers <nic_swsd@realtek.com>
CC: Francois Romieu <romieu@fr.zoreil.com>
CC: Jeff Garzik <jgarzik@pobox.com>
CC: Donald Becker <becker@scyld.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
diff --git a/drivers/net/ethernet/realtek/Kconfig b/drivers/net/ethernet/realtek/Kconfig
new file mode 100644
index 0000000..a5f67a09
--- /dev/null
+++ b/drivers/net/ethernet/realtek/Kconfig
@@ -0,0 +1,126 @@
+#
+# Realtek device configuration
+#
+
+config NET_VENDOR_REALTEK
+ bool "Realtek devices"
+ depends on PCI || (PARPORT && X86)
+ ---help---
+ If you have a network (Ethernet) card belonging to this class, say Y
+ and read the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ Note that the answer to this question doesn't directly affect the
+ kernel: saying N will just cause the configurator to skip all
+ the questions about Realtek devices. If you say Y, you will be asked for
+ your specific card in the following questions.
+
+if NET_VENDOR_REALTEK
+
+config ATP
+ tristate "AT-LAN-TEC/RealTek pocket adapter support"
+ depends on PARPORT && X86
+ select CRC32
+ ---help---
+ This is a network (Ethernet) device which attaches to your parallel
+ port. Read <file:drivers/net/atp.c> as well as the Ethernet-HOWTO,
+ available from <http://www.tldp.org/docs.html#howto>, if you
+ want to use this. If you intend to use this driver, you should have
+ said N to the "Parallel printer support", because the two drivers
+ don't like each other.
+
+ To compile this driver as a module, choose M here: the module
+ will be called atp.
+
+config 8139CP
+ tristate "RealTek RTL-8139 C+ PCI Fast Ethernet Adapter support (EXPERIMENTAL)"
+ depends on PCI && EXPERIMENTAL
+ select CRC32
+ select MII
+ ---help---
+ This is a driver for the Fast Ethernet PCI network cards based on
+ the RTL8139C+ chips. If you have one of those, say Y and read
+ the Ethernet-HOWTO, available from
+ <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here: the module
+ will be called 8139cp. This is recommended.
+
+config 8139TOO
+ tristate "RealTek RTL-8129/8130/8139 PCI Fast Ethernet Adapter support"
+ depends on PCI
+ select CRC32
+ select MII
+ ---help---
+ This is a driver for the Fast Ethernet PCI network cards based on
+ the RTL 8129/8130/8139 chips. If you have one of those, say Y and
+ read the Ethernet-HOWTO <http://www.tldp.org/docs.html#howto>.
+
+ To compile this driver as a module, choose M here: the module
+ will be called 8139too. This is recommended.
+
+config 8139TOO_PIO
+ bool "Use PIO instead of MMIO"
+ default y
+ depends on 8139TOO
+ ---help---
+ This instructs the driver to use programmed I/O ports (PIO) instead
+ of PCI shared memory (MMIO). This can possibly solve some problems
+ in case your mainboard has memory consistency issues. If unsure,
+ say N.
+
+config 8139TOO_TUNE_TWISTER
+ bool "Support for uncommon RTL-8139 rev. K (automatic channel equalization)"
+ depends on 8139TOO
+ ---help---
+ This implements a function which might come in handy in case you
+ are using low quality on long cabling. It is required for RealTek
+ RTL-8139 revision K boards, and totally unused otherwise. It tries
+ to match the transceiver to the cable characteristics. This is
+ experimental since hardly documented by the manufacturer.
+ If unsure, say Y.
+
+config 8139TOO_8129
+ bool "Support for older RTL-8129/8130 boards"
+ depends on 8139TOO
+ ---help---
+ This enables support for the older and uncommon RTL-8129 and
+ RTL-8130 chips, which support MII via an external transceiver,
+ instead of an internal one. Disabling this option will save some
+ memory by making the code size smaller. If unsure, say Y.
+
+config 8139_OLD_RX_RESET
+ bool "Use older RX-reset method"
+ depends on 8139TOO
+ ---help---
+ The 8139too driver was recently updated to contain a more rapid
+ reset sequence, in the face of severe receive errors. This "new"
+ RX-reset method should be adequate for all boards. But if you
+ experience problems, you can enable this option to restore the
+ old RX-reset behavior. If unsure, say N.
+
+config R8169
+ tristate "Realtek 8169 gigabit ethernet support"
+ depends on PCI
+ select FW_LOADER
+ select CRC32
+ select MII
+ ---help---
+ Say Y here if you have a Realtek 8169 PCI Gigabit Ethernet adapter.
+
+ To compile this driver as a module, choose M here: the module
+ will be called r8169. This is recommended.
+
+config SC92031
+ tristate "Silan SC92031 PCI Fast Ethernet Adapter driver (EXPERIMENTAL)"
+ depends on PCI && EXPERIMENTAL
+ select CRC32
+ ---help---
+ This is a driver for the Fast Ethernet PCI network cards based on
+ the Silan SC92031 chip (sometimes also called Rsltek 8139D). If you
+ have one of these, say Y here.
+
+ To compile this driver as a module, choose M here: the module
+ will be called sc92031. This is recommended.
+
+endif # NET_VENDOR_REALTEK