Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless

John W. Linville says:

====================
This is a batch of fixes intended for the 3.6 stream.

Arend van Spriel sends a simple thinko fix to correct a constant,
preventing the setting of an invalid power level.

Colin Ian King gives us a simple allocation failure check to avoid a
NULL pointer dereference.

Felix Fietkau sends another ath9k tx power patch, this time disabling a
feature that has been reported to cause rx problems.

Hante Meuleman provides a pair of endian fixes for brcmfmac.

Larry Finger offers an rtlwifi fix that avoids a system lockup related
to loading the wrong firmware for RTL8188CE devices.

These have been in linux-next for a few days and I think they should be
included in the final 3.6 kernel if possible.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/Documentation/ABI/testing/sysfs-bus-pci b/Documentation/ABI/testing/sysfs-bus-pci
index 34f5110..dff1f48 100644
--- a/Documentation/ABI/testing/sysfs-bus-pci
+++ b/Documentation/ABI/testing/sysfs-bus-pci
@@ -210,3 +210,15 @@
 		firmware assigned instance number of the PCI
 		device that can help in understanding the firmware
 		intended order of the PCI device.
+
+What:		/sys/bus/pci/devices/.../d3cold_allowed
+Date:		July 2012
+Contact:	Huang Ying <ying.huang@intel.com>
+Description:
+		d3cold_allowed is bit to control whether the corresponding PCI
+		device can be put into D3Cold state.  If it is cleared, the
+		device will never be put into D3Cold state.  If it is set, the
+		device may be put into D3Cold state if other requirements are
+		satisfied too.  Reading this attribute will show the current
+		value of d3cold_allowed bit.  Writing this attribute will set
+		the value of d3cold_allowed bit.
diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt
index afaff31..f4d8c71 100644
--- a/Documentation/feature-removal-schedule.txt
+++ b/Documentation/feature-removal-schedule.txt
@@ -579,7 +579,7 @@
 ----------------------------
 
 What:	at91-mci driver ("CONFIG_MMC_AT91")
-When:	3.7
+When:	3.8
 Why:	There are two mci drivers: at91-mci and atmel-mci. The PDC support
 	was added to atmel-mci as a first step to support more chips.
 	Then at91-mci was kept only for old IP versions (on at91rm9200 and
diff --git a/Documentation/i2c/busses/i2c-i801 b/Documentation/i2c/busses/i2c-i801
index 615142d..157416e7 100644
--- a/Documentation/i2c/busses/i2c-i801
+++ b/Documentation/i2c/busses/i2c-i801
@@ -21,6 +21,7 @@
   * Intel DH89xxCC (PCH)
   * Intel Panther Point (PCH)
   * Intel Lynx Point (PCH)
+  * Intel Lynx Point-LP (PCH)
    Datasheets: Publicly available at the Intel website
 
 On Intel Patsburg and later chipsets, both the normal host SMBus controller
diff --git a/MAINTAINERS b/MAINTAINERS
index fdc0119..53cc13c 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3388,7 +3388,7 @@
 L:	linux-i2c@vger.kernel.org
 W:	http://i2c.wiki.kernel.org/
 T:	quilt kernel.org/pub/linux/kernel/people/jdelvare/linux-2.6/jdelvare-i2c/
-T:	git git://git.fluff.org/bjdooks/linux.git
+T:	git git://git.pengutronix.de/git/wsa/linux.git
 S:	Maintained
 F:	Documentation/i2c/
 F:	drivers/i2c/
diff --git a/Makefile b/Makefile
index 371ce88..0f66f14 100644
--- a/Makefile
+++ b/Makefile
@@ -1,7 +1,7 @@
 VERSION = 3
 PATCHLEVEL = 6
 SUBLEVEL = 0
-EXTRAVERSION = -rc4
+EXTRAVERSION = -rc5
 NAME = Saber-toothed Squirrel
 
 # *DOCUMENTATION*
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index c5f9ae5..2f88d8d 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -6,7 +6,7 @@
 	select HAVE_DMA_API_DEBUG
 	select HAVE_IDE if PCI || ISA || PCMCIA
 	select HAVE_DMA_ATTRS
-	select HAVE_DMA_CONTIGUOUS if (CPU_V6 || CPU_V6K || CPU_V7)
+	select HAVE_DMA_CONTIGUOUS if MMU
 	select HAVE_MEMBLOCK
 	select RTC_LIB
 	select SYS_SUPPORTS_APM_EMULATION
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index f15f82b..e968a52 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -356,15 +356,15 @@
 		  is nothing connected to read from the DCC.
 
 	config DEBUG_SEMIHOSTING
-		bool "Kernel low-level debug output via semihosting I"
+		bool "Kernel low-level debug output via semihosting I/O"
 		help
 		  Semihosting enables code running on an ARM target to use
 		  the I/O facilities on a host debugger/emulator through a
-		  simple SVC calls. The host debugger or emulator must have
+		  simple SVC call. The host debugger or emulator must have
 		  semihosting enabled for the special svc call to be trapped
 		  otherwise the kernel will crash.
 
-		  This is known to work with OpenOCD, as wellas
+		  This is known to work with OpenOCD, as well as
 		  ARM's Fast Models, or any other controlling environment
 		  that implements semihosting.
 
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index 30eae87..a051dfb 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -284,10 +284,10 @@
 zinstall uinstall install: vmlinux
 	$(Q)$(MAKE) $(build)=$(boot) MACHINE=$(MACHINE) $@
 
-%.dtb:
+%.dtb: scripts
 	$(Q)$(MAKE) $(build)=$(boot) MACHINE=$(MACHINE) $(boot)/$@
 
-dtbs:
+dtbs: scripts
 	$(Q)$(MAKE) $(build)=$(boot) MACHINE=$(MACHINE) $(boot)/$@
 
 # We use MRPROPER_FILES and CLEAN_FILES now
diff --git a/arch/arm/boot/compressed/head.S b/arch/arm/boot/compressed/head.S
index b8c64b8..81769c1 100644
--- a/arch/arm/boot/compressed/head.S
+++ b/arch/arm/boot/compressed/head.S
@@ -659,10 +659,14 @@
 #ifdef CONFIG_CPU_ENDIAN_BE8
 		orr	r0, r0, #1 << 25	@ big-endian page tables
 #endif
+		mrcne   p15, 0, r6, c2, c0, 2   @ read ttb control reg
 		orrne	r0, r0, #1		@ MMU enabled
 		movne	r1, #0xfffffffd		@ domain 0 = client
+		bic     r6, r6, #1 << 31        @ 32-bit translation system
+		bic     r6, r6, #3 << 0         @ use only ttbr0
 		mcrne	p15, 0, r3, c2, c0, 0	@ load page table pointer
 		mcrne	p15, 0, r1, c3, c0, 0	@ load domain access control
+		mcrne   p15, 0, r6, c2, c0, 2   @ load ttb control
 #endif
 		mcr	p15, 0, r0, c7, c5, 4	@ ISB
 		mcr	p15, 0, r0, c1, c0, 0	@ load control register
diff --git a/arch/arm/boot/dts/at91sam9g25ek.dts b/arch/arm/boot/dts/at91sam9g25ek.dts
index 7829a4d..96514c1 100644
--- a/arch/arm/boot/dts/at91sam9g25ek.dts
+++ b/arch/arm/boot/dts/at91sam9g25ek.dts
@@ -15,7 +15,7 @@
 	compatible = "atmel,at91sam9g25ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
 
 	chosen {
-		bootargs = "128M console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs";
+		bootargs = "console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs";
 	};
 
 	ahb {
diff --git a/arch/arm/configs/armadillo800eva_defconfig b/arch/arm/configs/armadillo800eva_defconfig
index 7d87184..90610c7 100644
--- a/arch/arm/configs/armadillo800eva_defconfig
+++ b/arch/arm/configs/armadillo800eva_defconfig
@@ -33,7 +33,7 @@
 CONFIG_FORCE_MAX_ZONEORDER=13
 CONFIG_ZBOOT_ROM_TEXT=0x0
 CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="console=tty0 console=ttySC1,115200 earlyprintk=sh-sci.1,115200 ignore_loglevel root=/dev/nfs ip=dhcp nfsroot=,rsize=4096,wsize=4096"
+CONFIG_CMDLINE="console=tty0 console=ttySC1,115200 earlyprintk=sh-sci.1,115200 ignore_loglevel root=/dev/nfs ip=dhcp nfsroot=,rsize=4096,wsize=4096 rw"
 CONFIG_CMDLINE_FORCE=y
 CONFIG_KEXEC=y
 CONFIG_VFP=y
diff --git a/arch/arm/include/asm/assembler.h b/arch/arm/include/asm/assembler.h
index 03fb936..5c8b3bf4 100644
--- a/arch/arm/include/asm/assembler.h
+++ b/arch/arm/include/asm/assembler.h
@@ -320,4 +320,12 @@
 	.size \name , . - \name
 	.endm
 
+	.macro check_uaccess, addr:req, size:req, limit:req, tmp:req, bad:req
+#ifndef CONFIG_CPU_USE_DOMAINS
+	adds	\tmp, \addr, #\size - 1
+	sbcccs	\tmp, \tmp, \limit
+	bcs	\bad
+#endif
+	.endm
+
 #endif /* __ASM_ASSEMBLER_H__ */
diff --git a/arch/arm/include/asm/dma-mapping.h b/arch/arm/include/asm/dma-mapping.h
index 2ae842d..5c44dcb 100644
--- a/arch/arm/include/asm/dma-mapping.h
+++ b/arch/arm/include/asm/dma-mapping.h
@@ -203,6 +203,13 @@
 }
 
 /*
+ * This can be called during early boot to increase the size of the atomic
+ * coherent DMA pool above the default value of 256KiB. It must be called
+ * before postcore_initcall.
+ */
+extern void __init init_dma_coherent_pool_size(unsigned long size);
+
+/*
  * This can be called during boot to increase the size of the consistent
  * DMA region above it's default value of 2MB. It must be called before the
  * memory allocator is initialised, i.e. before any core_initcall.
diff --git a/arch/arm/include/asm/memory.h b/arch/arm/include/asm/memory.h
index e965f1b..5f6ddcc 100644
--- a/arch/arm/include/asm/memory.h
+++ b/arch/arm/include/asm/memory.h
@@ -187,6 +187,7 @@
 #define __phys_to_virt(x)	((x) - PHYS_OFFSET + PAGE_OFFSET)
 #endif
 #endif
+#endif /* __ASSEMBLY__ */
 
 #ifndef PHYS_OFFSET
 #ifdef PLAT_PHYS_OFFSET
@@ -196,6 +197,8 @@
 #endif
 #endif
 
+#ifndef __ASSEMBLY__
+
 /*
  * PFNs are used to describe any physical page; this means
  * PFN 0 == physical address 0.
diff --git a/arch/arm/include/asm/tlb.h b/arch/arm/include/asm/tlb.h
index 314d466..99a19512 100644
--- a/arch/arm/include/asm/tlb.h
+++ b/arch/arm/include/asm/tlb.h
@@ -199,6 +199,9 @@
 {
 	pgtable_page_dtor(pte);
 
+#ifdef CONFIG_ARM_LPAE
+	tlb_add_flush(tlb, addr);
+#else
 	/*
 	 * With the classic ARM MMU, a pte page has two corresponding pmd
 	 * entries, each covering 1MB.
@@ -206,6 +209,7 @@
 	addr &= PMD_MASK;
 	tlb_add_flush(tlb, addr + SZ_1M - PAGE_SIZE);
 	tlb_add_flush(tlb, addr + SZ_1M);
+#endif
 
 	tlb_remove_page(tlb, pte);
 }
diff --git a/arch/arm/include/asm/uaccess.h b/arch/arm/include/asm/uaccess.h
index 479a635..77bd79f 100644
--- a/arch/arm/include/asm/uaccess.h
+++ b/arch/arm/include/asm/uaccess.h
@@ -101,28 +101,39 @@
 extern int __get_user_2(void *);
 extern int __get_user_4(void *);
 
-#define __get_user_x(__r2,__p,__e,__s,__i...)				\
+#define __GUP_CLOBBER_1	"lr", "cc"
+#ifdef CONFIG_CPU_USE_DOMAINS
+#define __GUP_CLOBBER_2	"ip", "lr", "cc"
+#else
+#define __GUP_CLOBBER_2 "lr", "cc"
+#endif
+#define __GUP_CLOBBER_4	"lr", "cc"
+
+#define __get_user_x(__r2,__p,__e,__l,__s)				\
 	   __asm__ __volatile__ (					\
 		__asmeq("%0", "r0") __asmeq("%1", "r2")			\
+		__asmeq("%3", "r1")					\
 		"bl	__get_user_" #__s				\
 		: "=&r" (__e), "=r" (__r2)				\
-		: "0" (__p)						\
-		: __i, "cc")
+		: "0" (__p), "r" (__l)					\
+		: __GUP_CLOBBER_##__s)
 
-#define get_user(x,p)							\
+#define __get_user_check(x,p)							\
 	({								\
+		unsigned long __limit = current_thread_info()->addr_limit - 1; \
 		register const typeof(*(p)) __user *__p asm("r0") = (p);\
 		register unsigned long __r2 asm("r2");			\
+		register unsigned long __l asm("r1") = __limit;		\
 		register int __e asm("r0");				\
 		switch (sizeof(*(__p))) {				\
 		case 1:							\
-			__get_user_x(__r2, __p, __e, 1, "lr");		\
-	       		break;						\
+			__get_user_x(__r2, __p, __e, __l, 1);		\
+			break;						\
 		case 2:							\
-			__get_user_x(__r2, __p, __e, 2, "r3", "lr");	\
+			__get_user_x(__r2, __p, __e, __l, 2);		\
 			break;						\
 		case 4:							\
-	       		__get_user_x(__r2, __p, __e, 4, "lr");		\
+			__get_user_x(__r2, __p, __e, __l, 4);		\
 			break;						\
 		default: __e = __get_user_bad(); break;			\
 		}							\
@@ -130,42 +141,57 @@
 		__e;							\
 	})
 
+#define get_user(x,p)							\
+	({								\
+		might_fault();						\
+		__get_user_check(x,p);					\
+	 })
+
 extern int __put_user_1(void *, unsigned int);
 extern int __put_user_2(void *, unsigned int);
 extern int __put_user_4(void *, unsigned int);
 extern int __put_user_8(void *, unsigned long long);
 
-#define __put_user_x(__r2,__p,__e,__s)					\
+#define __put_user_x(__r2,__p,__e,__l,__s)				\
 	   __asm__ __volatile__ (					\
 		__asmeq("%0", "r0") __asmeq("%2", "r2")			\
+		__asmeq("%3", "r1")					\
 		"bl	__put_user_" #__s				\
 		: "=&r" (__e)						\
-		: "0" (__p), "r" (__r2)					\
+		: "0" (__p), "r" (__r2), "r" (__l)			\
 		: "ip", "lr", "cc")
 
-#define put_user(x,p)							\
+#define __put_user_check(x,p)							\
 	({								\
+		unsigned long __limit = current_thread_info()->addr_limit - 1; \
 		register const typeof(*(p)) __r2 asm("r2") = (x);	\
 		register const typeof(*(p)) __user *__p asm("r0") = (p);\
+		register unsigned long __l asm("r1") = __limit;		\
 		register int __e asm("r0");				\
 		switch (sizeof(*(__p))) {				\
 		case 1:							\
-			__put_user_x(__r2, __p, __e, 1);		\
+			__put_user_x(__r2, __p, __e, __l, 1);		\
 			break;						\
 		case 2:							\
-			__put_user_x(__r2, __p, __e, 2);		\
+			__put_user_x(__r2, __p, __e, __l, 2);		\
 			break;						\
 		case 4:							\
-			__put_user_x(__r2, __p, __e, 4);		\
+			__put_user_x(__r2, __p, __e, __l, 4);		\
 			break;						\
 		case 8:							\
-			__put_user_x(__r2, __p, __e, 8);		\
+			__put_user_x(__r2, __p, __e, __l, 8);		\
 			break;						\
 		default: __e = __put_user_bad(); break;			\
 		}							\
 		__e;							\
 	})
 
+#define put_user(x,p)							\
+	({								\
+		might_fault();						\
+		__put_user_check(x,p);					\
+	 })
+
 #else /* CONFIG_MMU */
 
 /*
@@ -219,6 +245,7 @@
 	unsigned long __gu_addr = (unsigned long)(ptr);			\
 	unsigned long __gu_val;						\
 	__chk_user_ptr(ptr);						\
+	might_fault();							\
 	switch (sizeof(*(ptr))) {					\
 	case 1:	__get_user_asm_byte(__gu_val,__gu_addr,err);	break;	\
 	case 2:	__get_user_asm_half(__gu_val,__gu_addr,err);	break;	\
@@ -300,6 +327,7 @@
 	unsigned long __pu_addr = (unsigned long)(ptr);			\
 	__typeof__(*(ptr)) __pu_val = (x);				\
 	__chk_user_ptr(ptr);						\
+	might_fault();							\
 	switch (sizeof(*(ptr))) {					\
 	case 1: __put_user_asm_byte(__pu_val,__pu_addr,err);	break;	\
 	case 2: __put_user_asm_half(__pu_val,__pu_addr,err);	break;	\
diff --git a/arch/arm/kernel/hw_breakpoint.c b/arch/arm/kernel/hw_breakpoint.c
index ba386bd..281bf33 100644
--- a/arch/arm/kernel/hw_breakpoint.c
+++ b/arch/arm/kernel/hw_breakpoint.c
@@ -159,6 +159,12 @@
 		arch >= ARM_DEBUG_ARCH_V7_1;
 }
 
+/* Can we determine the watchpoint access type from the fsr? */
+static int debug_exception_updates_fsr(void)
+{
+	return 0;
+}
+
 /* Determine number of WRP registers available. */
 static int get_num_wrp_resources(void)
 {
@@ -604,13 +610,14 @@
 		/* Aligned */
 		break;
 	case 1:
-		/* Allow single byte watchpoint. */
-		if (info->ctrl.len == ARM_BREAKPOINT_LEN_1)
-			break;
 	case 2:
 		/* Allow halfword watchpoints and breakpoints. */
 		if (info->ctrl.len == ARM_BREAKPOINT_LEN_2)
 			break;
+	case 3:
+		/* Allow single byte watchpoint. */
+		if (info->ctrl.len == ARM_BREAKPOINT_LEN_1)
+			break;
 	default:
 		ret = -EINVAL;
 		goto out;
@@ -619,18 +626,35 @@
 	info->address &= ~alignment_mask;
 	info->ctrl.len <<= offset;
 
-	/*
-	 * Currently we rely on an overflow handler to take
-	 * care of single-stepping the breakpoint when it fires.
-	 * In the case of userspace breakpoints on a core with V7 debug,
-	 * we can use the mismatch feature as a poor-man's hardware
-	 * single-step, but this only works for per-task breakpoints.
-	 */
-	if (!bp->overflow_handler && (arch_check_bp_in_kernelspace(bp) ||
-	    !core_has_mismatch_brps() || !bp->hw.bp_target)) {
-		pr_warning("overflow handler required but none found\n");
-		ret = -EINVAL;
+	if (!bp->overflow_handler) {
+		/*
+		 * Mismatch breakpoints are required for single-stepping
+		 * breakpoints.
+		 */
+		if (!core_has_mismatch_brps())
+			return -EINVAL;
+
+		/* We don't allow mismatch breakpoints in kernel space. */
+		if (arch_check_bp_in_kernelspace(bp))
+			return -EPERM;
+
+		/*
+		 * Per-cpu breakpoints are not supported by our stepping
+		 * mechanism.
+		 */
+		if (!bp->hw.bp_target)
+			return -EINVAL;
+
+		/*
+		 * We only support specific access types if the fsr
+		 * reports them.
+		 */
+		if (!debug_exception_updates_fsr() &&
+		    (info->ctrl.type == ARM_BREAKPOINT_LOAD ||
+		     info->ctrl.type == ARM_BREAKPOINT_STORE))
+			return -EINVAL;
 	}
+
 out:
 	return ret;
 }
@@ -706,10 +730,12 @@
 				goto unlock;
 
 			/* Check that the access type matches. */
-			access = (fsr & ARM_FSR_ACCESS_MASK) ? HW_BREAKPOINT_W :
-				 HW_BREAKPOINT_R;
-			if (!(access & hw_breakpoint_type(wp)))
-				goto unlock;
+			if (debug_exception_updates_fsr()) {
+				access = (fsr & ARM_FSR_ACCESS_MASK) ?
+					  HW_BREAKPOINT_W : HW_BREAKPOINT_R;
+				if (!(access & hw_breakpoint_type(wp)))
+					goto unlock;
+			}
 
 			/* We have a winner. */
 			info->trigger = addr;
diff --git a/arch/arm/kernel/traps.c b/arch/arm/kernel/traps.c
index f794521..b0179b8 100644
--- a/arch/arm/kernel/traps.c
+++ b/arch/arm/kernel/traps.c
@@ -420,20 +420,23 @@
 #endif
 			instr = *(u32 *) pc;
 	} else if (thumb_mode(regs)) {
-		get_user(instr, (u16 __user *)pc);
+		if (get_user(instr, (u16 __user *)pc))
+			goto die_sig;
 		if (is_wide_instruction(instr)) {
 			unsigned int instr2;
-			get_user(instr2, (u16 __user *)pc+1);
+			if (get_user(instr2, (u16 __user *)pc+1))
+				goto die_sig;
 			instr <<= 16;
 			instr |= instr2;
 		}
-	} else {
-		get_user(instr, (u32 __user *)pc);
+	} else if (get_user(instr, (u32 __user *)pc)) {
+		goto die_sig;
 	}
 
 	if (call_undef_hook(regs, instr) == 0)
 		return;
 
+die_sig:
 #ifdef CONFIG_DEBUG_USER
 	if (user_debug & UDBG_UNDEFINED) {
 		printk(KERN_INFO "%s (%d): undefined instruction: pc=%p\n",
diff --git a/arch/arm/lib/delay.c b/arch/arm/lib/delay.c
index d6dacc6..395d5fb 100644
--- a/arch/arm/lib/delay.c
+++ b/arch/arm/lib/delay.c
@@ -59,6 +59,7 @@
 {
 	pr_info("Switching to timer-based delay loop\n");
 	lpj_fine			= freq / HZ;
+	loops_per_jiffy			= lpj_fine;
 	arm_delay_ops.delay		= __timer_delay;
 	arm_delay_ops.const_udelay	= __timer_const_udelay;
 	arm_delay_ops.udelay		= __timer_udelay;
diff --git a/arch/arm/lib/getuser.S b/arch/arm/lib/getuser.S
index 11093a7..9b06bb4 100644
--- a/arch/arm/lib/getuser.S
+++ b/arch/arm/lib/getuser.S
@@ -16,8 +16,9 @@
  * __get_user_X
  *
  * Inputs:	r0 contains the address
+ *		r1 contains the address limit, which must be preserved
  * Outputs:	r0 is the error code
- *		r2, r3 contains the zero-extended value
+ *		r2 contains the zero-extended value
  *		lr corrupted
  *
  * No other registers must be altered.  (see <asm/uaccess.h>
@@ -27,33 +28,39 @@
  * Note also that it is intended that __get_user_bad is not global.
  */
 #include <linux/linkage.h>
+#include <asm/assembler.h>
 #include <asm/errno.h>
 #include <asm/domain.h>
 
 ENTRY(__get_user_1)
+	check_uaccess r0, 1, r1, r2, __get_user_bad
 1: TUSER(ldrb)	r2, [r0]
 	mov	r0, #0
 	mov	pc, lr
 ENDPROC(__get_user_1)
 
 ENTRY(__get_user_2)
-#ifdef CONFIG_THUMB2_KERNEL
-2: TUSER(ldrb)	r2, [r0]
-3: TUSER(ldrb)	r3, [r0, #1]
+	check_uaccess r0, 2, r1, r2, __get_user_bad
+#ifdef CONFIG_CPU_USE_DOMAINS
+rb	.req	ip
+2:	ldrbt	r2, [r0], #1
+3:	ldrbt	rb, [r0], #0
 #else
-2: TUSER(ldrb)	r2, [r0], #1
-3: TUSER(ldrb)	r3, [r0]
+rb	.req	r0
+2:	ldrb	r2, [r0]
+3:	ldrb	rb, [r0, #1]
 #endif
 #ifndef __ARMEB__
-	orr	r2, r2, r3, lsl #8
+	orr	r2, r2, rb, lsl #8
 #else
-	orr	r2, r3, r2, lsl #8
+	orr	r2, rb, r2, lsl #8
 #endif
 	mov	r0, #0
 	mov	pc, lr
 ENDPROC(__get_user_2)
 
 ENTRY(__get_user_4)
+	check_uaccess r0, 4, r1, r2, __get_user_bad
 4: TUSER(ldr)	r2, [r0]
 	mov	r0, #0
 	mov	pc, lr
diff --git a/arch/arm/lib/putuser.S b/arch/arm/lib/putuser.S
index 7db2599..3d73dcb 100644
--- a/arch/arm/lib/putuser.S
+++ b/arch/arm/lib/putuser.S
@@ -16,6 +16,7 @@
  * __put_user_X
  *
  * Inputs:	r0 contains the address
+ *		r1 contains the address limit, which must be preserved
  *		r2, r3 contains the value
  * Outputs:	r0 is the error code
  *		lr corrupted
@@ -27,16 +28,19 @@
  * Note also that it is intended that __put_user_bad is not global.
  */
 #include <linux/linkage.h>
+#include <asm/assembler.h>
 #include <asm/errno.h>
 #include <asm/domain.h>
 
 ENTRY(__put_user_1)
+	check_uaccess r0, 1, r1, ip, __put_user_bad
 1: TUSER(strb)	r2, [r0]
 	mov	r0, #0
 	mov	pc, lr
 ENDPROC(__put_user_1)
 
 ENTRY(__put_user_2)
+	check_uaccess r0, 2, r1, ip, __put_user_bad
 	mov	ip, r2, lsr #8
 #ifdef CONFIG_THUMB2_KERNEL
 #ifndef __ARMEB__
@@ -60,12 +64,14 @@
 ENDPROC(__put_user_2)
 
 ENTRY(__put_user_4)
+	check_uaccess r0, 4, r1, ip, __put_user_bad
 4: TUSER(str)	r2, [r0]
 	mov	r0, #0
 	mov	pc, lr
 ENDPROC(__put_user_4)
 
 ENTRY(__put_user_8)
+	check_uaccess r0, 8, r1, ip, __put_user_bad
 #ifdef CONFIG_THUMB2_KERNEL
 5: TUSER(str)	r2, [r0]
 6: TUSER(str)	r3, [r0, #4]
diff --git a/arch/arm/mach-at91/at91rm9200_time.c b/arch/arm/mach-at91/at91rm9200_time.c
index 104ca40..aaa443b 100644
--- a/arch/arm/mach-at91/at91rm9200_time.c
+++ b/arch/arm/mach-at91/at91rm9200_time.c
@@ -197,7 +197,7 @@
 	at91_st_read(AT91_ST_SR);
 
 	/* Make IRQs happen for the system timer */
-	setup_irq(AT91_ID_SYS, &at91rm9200_timer_irq);
+	setup_irq(NR_IRQS_LEGACY + AT91_ID_SYS, &at91rm9200_timer_irq);
 
 	/* The 32KiHz "Slow Clock" (tick every 30517.58 nanoseconds) is used
 	 * directly for the clocksource and all clockevents, after adjusting
diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c
index 7b9c2ba..bce572a 100644
--- a/arch/arm/mach-at91/at91sam9260_devices.c
+++ b/arch/arm/mach-at91/at91sam9260_devices.c
@@ -726,6 +726,8 @@
 		.flags	= IORESOURCE_MEM,
 	}, {
 		.flags	= IORESOURCE_MEM,
+	}, {
+		.flags  = IORESOURCE_IRQ,
 	},
 };
 
@@ -744,10 +746,12 @@
 	 * The second resource is needed:
 	 * GPBR will serve as the storage for RTC time offset
 	 */
-	at91sam9260_rtt_device.num_resources = 2;
+	at91sam9260_rtt_device.num_resources = 3;
 	rtt_resources[1].start = AT91SAM9260_BASE_GPBR +
 				 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
 	rtt_resources[1].end = rtt_resources[1].start + 3;
+	rtt_resources[2].start = NR_IRQS_LEGACY + AT91_ID_SYS;
+	rtt_resources[2].end = NR_IRQS_LEGACY + AT91_ID_SYS;
 }
 #else
 static void __init at91_add_device_rtt_rtc(void)
diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c
index 8df5c1bd..bc2590d 100644
--- a/arch/arm/mach-at91/at91sam9261_devices.c
+++ b/arch/arm/mach-at91/at91sam9261_devices.c
@@ -609,6 +609,8 @@
 		.flags	= IORESOURCE_MEM,
 	}, {
 		.flags	= IORESOURCE_MEM,
+	}, {
+		.flags  = IORESOURCE_IRQ,
 	}
 };
 
@@ -626,10 +628,12 @@
 	 * The second resource is needed:
 	 * GPBR will serve as the storage for RTC time offset
 	 */
-	at91sam9261_rtt_device.num_resources = 2;
+	at91sam9261_rtt_device.num_resources = 3;
 	rtt_resources[1].start = AT91SAM9261_BASE_GPBR +
 				 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
 	rtt_resources[1].end = rtt_resources[1].start + 3;
+	rtt_resources[2].start = NR_IRQS_LEGACY + AT91_ID_SYS;
+	rtt_resources[2].end = NR_IRQS_LEGACY + AT91_ID_SYS;
 }
 #else
 static void __init at91_add_device_rtt_rtc(void)
diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c
index eb6bbf8..9b6ca734 100644
--- a/arch/arm/mach-at91/at91sam9263_devices.c
+++ b/arch/arm/mach-at91/at91sam9263_devices.c
@@ -990,6 +990,8 @@
 		.flags	= IORESOURCE_MEM,
 	}, {
 		.flags	= IORESOURCE_MEM,
+	}, {
+		.flags  = IORESOURCE_IRQ,
 	}
 };
 
@@ -1006,6 +1008,8 @@
 		.flags	= IORESOURCE_MEM,
 	}, {
 		.flags	= IORESOURCE_MEM,
+	}, {
+		.flags  = IORESOURCE_IRQ,
 	}
 };
 
@@ -1027,14 +1031,14 @@
 		 * The second resource is needed only for the chosen RTT:
 		 * GPBR will serve as the storage for RTC time offset
 		 */
-		at91sam9263_rtt0_device.num_resources = 2;
+		at91sam9263_rtt0_device.num_resources = 3;
 		at91sam9263_rtt1_device.num_resources = 1;
 		pdev = &at91sam9263_rtt0_device;
 		r = rtt0_resources;
 		break;
 	case 1:
 		at91sam9263_rtt0_device.num_resources = 1;
-		at91sam9263_rtt1_device.num_resources = 2;
+		at91sam9263_rtt1_device.num_resources = 3;
 		pdev = &at91sam9263_rtt1_device;
 		r = rtt1_resources;
 		break;
@@ -1047,6 +1051,8 @@
 	pdev->name = "rtc-at91sam9";
 	r[1].start = AT91SAM9263_BASE_GPBR + 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
 	r[1].end = r[1].start + 3;
+	r[2].start = NR_IRQS_LEGACY + AT91_ID_SYS;
+	r[2].end = NR_IRQS_LEGACY + AT91_ID_SYS;
 }
 #else
 static void __init at91_add_device_rtt_rtc(void)
diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c
index 0607399..1b47319 100644
--- a/arch/arm/mach-at91/at91sam9g45_devices.c
+++ b/arch/arm/mach-at91/at91sam9g45_devices.c
@@ -1293,6 +1293,8 @@
 		.flags	= IORESOURCE_MEM,
 	}, {
 		.flags	= IORESOURCE_MEM,
+	}, {
+		.flags  = IORESOURCE_IRQ,
 	}
 };
 
@@ -1310,10 +1312,12 @@
 	 * The second resource is needed:
 	 * GPBR will serve as the storage for RTC time offset
 	 */
-	at91sam9g45_rtt_device.num_resources = 2;
+	at91sam9g45_rtt_device.num_resources = 3;
 	rtt_resources[1].start = AT91SAM9G45_BASE_GPBR +
 				 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
 	rtt_resources[1].end = rtt_resources[1].start + 3;
+	rtt_resources[2].start = NR_IRQS_LEGACY + AT91_ID_SYS;
+	rtt_resources[2].end = NR_IRQS_LEGACY + AT91_ID_SYS;
 }
 #else
 static void __init at91_add_device_rtt_rtc(void)
diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c
index f09fff9..b3d365d 100644
--- a/arch/arm/mach-at91/at91sam9rl_devices.c
+++ b/arch/arm/mach-at91/at91sam9rl_devices.c
@@ -688,6 +688,8 @@
 		.flags	= IORESOURCE_MEM,
 	}, {
 		.flags	= IORESOURCE_MEM,
+	}, {
+		.flags  = IORESOURCE_IRQ,
 	}
 };
 
@@ -705,10 +707,12 @@
 	 * The second resource is needed:
 	 * GPBR will serve as the storage for RTC time offset
 	 */
-	at91sam9rl_rtt_device.num_resources = 2;
+	at91sam9rl_rtt_device.num_resources = 3;
 	rtt_resources[1].start = AT91SAM9RL_BASE_GPBR +
 				 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
 	rtt_resources[1].end = rtt_resources[1].start + 3;
+	rtt_resources[2].start = NR_IRQS_LEGACY + AT91_ID_SYS;
+	rtt_resources[2].end = NR_IRQS_LEGACY + AT91_ID_SYS;
 }
 #else
 static void __init at91_add_device_rtt_rtc(void)
diff --git a/arch/arm/mach-at91/clock.c b/arch/arm/mach-at91/clock.c
index de2ec6b..188c829 100644
--- a/arch/arm/mach-at91/clock.c
+++ b/arch/arm/mach-at91/clock.c
@@ -63,6 +63,12 @@
 
 #define cpu_has_300M_plla()	(cpu_is_at91sam9g10())
 
+#define cpu_has_240M_plla()	(cpu_is_at91sam9261() \
+				|| cpu_is_at91sam9263() \
+				|| cpu_is_at91sam9rl())
+
+#define cpu_has_210M_plla()	(cpu_is_at91sam9260())
+
 #define cpu_has_pllb()		(!(cpu_is_at91sam9rl() \
 				|| cpu_is_at91sam9g45() \
 				|| cpu_is_at91sam9x5() \
@@ -706,6 +712,12 @@
 	} else if (cpu_has_800M_plla()) {
 		if (plla.rate_hz > 800000000)
 			pll_overclock = true;
+	} else if (cpu_has_240M_plla()) {
+		if (plla.rate_hz > 240000000)
+			pll_overclock = true;
+	} else if (cpu_has_210M_plla()) {
+		if (plla.rate_hz > 210000000)
+			pll_overclock = true;
 	} else {
 		if (plla.rate_hz > 209000000)
 			pll_overclock = true;
diff --git a/arch/arm/mach-gemini/irq.c b/arch/arm/mach-gemini/irq.c
index ca70e5f..020852d 100644
--- a/arch/arm/mach-gemini/irq.c
+++ b/arch/arm/mach-gemini/irq.c
@@ -17,6 +17,7 @@
 #include <linux/sched.h>
 #include <asm/irq.h>
 #include <asm/mach/irq.h>
+#include <asm/system_misc.h>
 #include <mach/hardware.h>
 
 #define IRQ_SOURCE(base_addr)	(base_addr + 0x00)
diff --git a/arch/arm/mach-imx/clk-imx25.c b/arch/arm/mach-imx/clk-imx25.c
index fdd8cc8..4431a62 100644
--- a/arch/arm/mach-imx/clk-imx25.c
+++ b/arch/arm/mach-imx/clk-imx25.c
@@ -222,10 +222,8 @@
 	clk_register_clkdev(clk[lcdc_ipg], "ipg", "imx-fb.0");
 	clk_register_clkdev(clk[lcdc_ahb], "ahb", "imx-fb.0");
 	clk_register_clkdev(clk[wdt_ipg], NULL, "imx2-wdt.0");
-	clk_register_clkdev(clk[ssi1_ipg_per], "per", "imx-ssi.0");
-	clk_register_clkdev(clk[ssi1_ipg], "ipg", "imx-ssi.0");
-	clk_register_clkdev(clk[ssi2_ipg_per], "per", "imx-ssi.1");
-	clk_register_clkdev(clk[ssi2_ipg], "ipg", "imx-ssi.1");
+	clk_register_clkdev(clk[ssi1_ipg], NULL, "imx-ssi.0");
+	clk_register_clkdev(clk[ssi2_ipg], NULL, "imx-ssi.1");
 	clk_register_clkdev(clk[esdhc1_ipg_per], "per", "sdhci-esdhc-imx25.0");
 	clk_register_clkdev(clk[esdhc1_ipg], "ipg", "sdhci-esdhc-imx25.0");
 	clk_register_clkdev(clk[esdhc1_ahb], "ahb", "sdhci-esdhc-imx25.0");
diff --git a/arch/arm/mach-imx/clk-imx35.c b/arch/arm/mach-imx/clk-imx35.c
index c6422fb..65fb8bc 100644
--- a/arch/arm/mach-imx/clk-imx35.c
+++ b/arch/arm/mach-imx/clk-imx35.c
@@ -230,10 +230,8 @@
 	clk_register_clkdev(clk[ipu_gate], NULL, "mx3_sdc_fb");
 	clk_register_clkdev(clk[owire_gate], NULL, "mxc_w1");
 	clk_register_clkdev(clk[sdma_gate], NULL, "imx35-sdma");
-	clk_register_clkdev(clk[ipg], "ipg", "imx-ssi.0");
-	clk_register_clkdev(clk[ssi1_div_post], "per", "imx-ssi.0");
-	clk_register_clkdev(clk[ipg], "ipg", "imx-ssi.1");
-	clk_register_clkdev(clk[ssi2_div_post], "per", "imx-ssi.1");
+	clk_register_clkdev(clk[ssi1_gate], NULL, "imx-ssi.0");
+	clk_register_clkdev(clk[ssi2_gate], NULL, "imx-ssi.1");
 	/* i.mx35 has the i.mx21 type uart */
 	clk_register_clkdev(clk[uart1_gate], "per", "imx21-uart.0");
 	clk_register_clkdev(clk[ipg], "ipg", "imx21-uart.0");
diff --git a/arch/arm/mach-kirkwood/common.c b/arch/arm/mach-kirkwood/common.c
index 3226077..1201191 100644
--- a/arch/arm/mach-kirkwood/common.c
+++ b/arch/arm/mach-kirkwood/common.c
@@ -517,6 +517,13 @@
 void __init kirkwood_init_early(void)
 {
 	orion_time_set_base(TIMER_VIRT_BASE);
+
+	/*
+	 * Some Kirkwood devices allocate their coherent buffers from atomic
+	 * context. Increase size of atomic coherent pool to make sure such
+	 * the allocations won't fail.
+	 */
+	init_dma_coherent_pool_size(SZ_1M);
 }
 
 int kirkwood_tclk;
diff --git a/arch/arm/mach-kirkwood/db88f6281-bp-setup.c b/arch/arm/mach-kirkwood/db88f6281-bp-setup.c
index d933593..be90b7d 100644
--- a/arch/arm/mach-kirkwood/db88f6281-bp-setup.c
+++ b/arch/arm/mach-kirkwood/db88f6281-bp-setup.c
@@ -10,6 +10,7 @@
 
 #include <linux/kernel.h>
 #include <linux/init.h>
+#include <linux/sizes.h>
 #include <linux/platform_device.h>
 #include <linux/mtd/partitions.h>
 #include <linux/ata_platform.h>
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index fcd4e85..346fd26 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -232,10 +232,11 @@
 	select OMAP_PACKAGE_CBB
 	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 
-config MACH_OMAP3_TOUCHBOOK
+config MACH_TOUCHBOOK
 	bool "OMAP3 Touch Book"
 	depends on ARCH_OMAP3
 	default y
+	select OMAP_PACKAGE_CBB
 
 config MACH_OMAP_3430SDP
 	bool "OMAP 3430 SDP board"
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index f6a24b3..34c2c7f 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -255,7 +255,7 @@
 obj-$(CONFIG_MACH_CM_T35)		+= board-cm-t35.o
 obj-$(CONFIG_MACH_CM_T3517)		+= board-cm-t3517.o
 obj-$(CONFIG_MACH_IGEP0020)		+= board-igep0020.o
-obj-$(CONFIG_MACH_OMAP3_TOUCHBOOK)	+= board-omap3touchbook.o
+obj-$(CONFIG_MACH_TOUCHBOOK)		+= board-omap3touchbook.o
 obj-$(CONFIG_MACH_OMAP_4430SDP)		+= board-4430sdp.o
 obj-$(CONFIG_MACH_OMAP4_PANDA)		+= board-omap4panda.o
 
diff --git a/arch/arm/mach-omap2/clock33xx_data.c b/arch/arm/mach-omap2/clock33xx_data.c
index 25bbcc7..ae27de8 100644
--- a/arch/arm/mach-omap2/clock33xx_data.c
+++ b/arch/arm/mach-omap2/clock33xx_data.c
@@ -1036,13 +1036,13 @@
 	CLK(NULL,	"mmu_fck",		&mmu_fck,	CK_AM33XX),
 	CLK(NULL,	"smartreflex0_fck",	&smartreflex0_fck,	CK_AM33XX),
 	CLK(NULL,	"smartreflex1_fck",	&smartreflex1_fck,	CK_AM33XX),
-	CLK(NULL,	"gpt1_fck",		&timer1_fck,	CK_AM33XX),
-	CLK(NULL,	"gpt2_fck",		&timer2_fck,	CK_AM33XX),
-	CLK(NULL,	"gpt3_fck",		&timer3_fck,	CK_AM33XX),
-	CLK(NULL,	"gpt4_fck",		&timer4_fck,	CK_AM33XX),
-	CLK(NULL,	"gpt5_fck",		&timer5_fck,	CK_AM33XX),
-	CLK(NULL,	"gpt6_fck",		&timer6_fck,	CK_AM33XX),
-	CLK(NULL,	"gpt7_fck",		&timer7_fck,	CK_AM33XX),
+	CLK(NULL,	"timer1_fck",		&timer1_fck,	CK_AM33XX),
+	CLK(NULL,	"timer2_fck",		&timer2_fck,	CK_AM33XX),
+	CLK(NULL,	"timer3_fck",		&timer3_fck,	CK_AM33XX),
+	CLK(NULL,	"timer4_fck",		&timer4_fck,	CK_AM33XX),
+	CLK(NULL,	"timer5_fck",		&timer5_fck,	CK_AM33XX),
+	CLK(NULL,	"timer6_fck",		&timer6_fck,	CK_AM33XX),
+	CLK(NULL,	"timer7_fck",		&timer7_fck,	CK_AM33XX),
 	CLK(NULL,	"usbotg_fck",		&usbotg_fck,	CK_AM33XX),
 	CLK(NULL,	"ieee5000_fck",		&ieee5000_fck,	CK_AM33XX),
 	CLK(NULL,	"wdt1_fck",		&wdt1_fck,	CK_AM33XX),
diff --git a/arch/arm/mach-omap2/clockdomain2xxx_3xxx.c b/arch/arm/mach-omap2/clockdomain2xxx_3xxx.c
index a0d68db..f99e65c 100644
--- a/arch/arm/mach-omap2/clockdomain2xxx_3xxx.c
+++ b/arch/arm/mach-omap2/clockdomain2xxx_3xxx.c
@@ -241,6 +241,52 @@
 		_clkdm_del_autodeps(clkdm);
 }
 
+static int omap3xxx_clkdm_clk_enable(struct clockdomain *clkdm)
+{
+	bool hwsup = false;
+
+	if (!clkdm->clktrctrl_mask)
+		return 0;
+
+	hwsup = omap2_cm_is_clkdm_in_hwsup(clkdm->pwrdm.ptr->prcm_offs,
+				clkdm->clktrctrl_mask);
+
+	if (hwsup) {
+		/* Disable HW transitions when we are changing deps */
+		_disable_hwsup(clkdm);
+		_clkdm_add_autodeps(clkdm);
+		_enable_hwsup(clkdm);
+	} else {
+		if (clkdm->flags & CLKDM_CAN_FORCE_WAKEUP)
+			omap3_clkdm_wakeup(clkdm);
+	}
+
+	return 0;
+}
+
+static int omap3xxx_clkdm_clk_disable(struct clockdomain *clkdm)
+{
+	bool hwsup = false;
+
+	if (!clkdm->clktrctrl_mask)
+		return 0;
+
+	hwsup = omap2_cm_is_clkdm_in_hwsup(clkdm->pwrdm.ptr->prcm_offs,
+				clkdm->clktrctrl_mask);
+
+	if (hwsup) {
+		/* Disable HW transitions when we are changing deps */
+		_disable_hwsup(clkdm);
+		_clkdm_del_autodeps(clkdm);
+		_enable_hwsup(clkdm);
+	} else {
+		if (clkdm->flags & CLKDM_CAN_FORCE_SLEEP)
+			omap3_clkdm_sleep(clkdm);
+	}
+
+	return 0;
+}
+
 struct clkdm_ops omap2_clkdm_operations = {
 	.clkdm_add_wkdep	= omap2_clkdm_add_wkdep,
 	.clkdm_del_wkdep	= omap2_clkdm_del_wkdep,
@@ -267,6 +313,6 @@
 	.clkdm_wakeup		= omap3_clkdm_wakeup,
 	.clkdm_allow_idle	= omap3_clkdm_allow_idle,
 	.clkdm_deny_idle	= omap3_clkdm_deny_idle,
-	.clkdm_clk_enable	= omap2_clkdm_clk_enable,
-	.clkdm_clk_disable	= omap2_clkdm_clk_disable,
+	.clkdm_clk_enable	= omap3xxx_clkdm_clk_enable,
+	.clkdm_clk_disable	= omap3xxx_clkdm_clk_disable,
 };
diff --git a/arch/arm/mach-omap2/cm-regbits-34xx.h b/arch/arm/mach-omap2/cm-regbits-34xx.h
index 766338f..975f6bd 100644
--- a/arch/arm/mach-omap2/cm-regbits-34xx.h
+++ b/arch/arm/mach-omap2/cm-regbits-34xx.h
@@ -67,6 +67,7 @@
 #define OMAP3430_EN_IVA2_DPLL_MASK			(0x7 << 0)
 
 /* CM_IDLEST_IVA2 */
+#define OMAP3430_ST_IVA2_SHIFT				0
 #define OMAP3430_ST_IVA2_MASK				(1 << 0)
 
 /* CM_IDLEST_PLL_IVA2 */
diff --git a/arch/arm/mach-omap2/omap-wakeupgen.c b/arch/arm/mach-omap2/omap-wakeupgen.c
index 05fdebf..330d4c6 100644
--- a/arch/arm/mach-omap2/omap-wakeupgen.c
+++ b/arch/arm/mach-omap2/omap-wakeupgen.c
@@ -46,7 +46,7 @@
 static void __iomem *wakeupgen_base;
 static void __iomem *sar_base;
 static DEFINE_SPINLOCK(wakeupgen_lock);
-static unsigned int irq_target_cpu[NR_IRQS];
+static unsigned int irq_target_cpu[MAX_IRQS];
 static unsigned int irq_banks = MAX_NR_REG_BANKS;
 static unsigned int max_irqs = MAX_IRQS;
 static unsigned int omap_secure_apis;
diff --git a/arch/arm/mach-omap2/omap_hwmod.c b/arch/arm/mach-omap2/omap_hwmod.c
index 6ca8e51..37afbd1 100644
--- a/arch/arm/mach-omap2/omap_hwmod.c
+++ b/arch/arm/mach-omap2/omap_hwmod.c
@@ -1889,6 +1889,7 @@
 			_enable_sysc(oh);
 		}
 	} else {
+		_omap4_disable_module(oh);
 		_disable_clocks(oh);
 		pr_debug("omap_hwmod: %s: _wait_target_ready: %d\n",
 			 oh->name, r);
diff --git a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
index c9e3820..ce7e606 100644
--- a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
@@ -100,9 +100,9 @@
 
 /* IVA2 (IVA2) */
 static struct omap_hwmod_rst_info omap3xxx_iva_resets[] = {
-	{ .name = "logic", .rst_shift = 0 },
-	{ .name = "seq0", .rst_shift = 1 },
-	{ .name = "seq1", .rst_shift = 2 },
+	{ .name = "logic", .rst_shift = 0, .st_shift = 8 },
+	{ .name = "seq0", .rst_shift = 1, .st_shift = 9 },
+	{ .name = "seq1", .rst_shift = 2, .st_shift = 10 },
 };
 
 static struct omap_hwmod omap3xxx_iva_hwmod = {
@@ -112,6 +112,15 @@
 	.rst_lines	= omap3xxx_iva_resets,
 	.rst_lines_cnt	= ARRAY_SIZE(omap3xxx_iva_resets),
 	.main_clk	= "iva2_ck",
+	.prcm = {
+		.omap2 = {
+			.module_offs = OMAP3430_IVA2_MOD,
+			.prcm_reg_id = 1,
+			.module_bit = OMAP3430_CM_FCLKEN_IVA2_EN_IVA2_SHIFT,
+			.idlest_reg_id = 1,
+			.idlest_idle_bit = OMAP3430_ST_IVA2_SHIFT,
+		}
+	},
 };
 
 /* timer class */
diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
index 242aee4..afb6091 100644
--- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c
@@ -4210,7 +4210,7 @@
 };
 
 /* dsp -> sl2if */
-static struct omap_hwmod_ocp_if omap44xx_dsp__sl2if = {
+static struct omap_hwmod_ocp_if __maybe_unused omap44xx_dsp__sl2if = {
 	.master		= &omap44xx_dsp_hwmod,
 	.slave		= &omap44xx_sl2if_hwmod,
 	.clk		= "dpll_iva_m5x2_ck",
@@ -4828,7 +4828,7 @@
 };
 
 /* iva -> sl2if */
-static struct omap_hwmod_ocp_if omap44xx_iva__sl2if = {
+static struct omap_hwmod_ocp_if __maybe_unused omap44xx_iva__sl2if = {
 	.master		= &omap44xx_iva_hwmod,
 	.slave		= &omap44xx_sl2if_hwmod,
 	.clk		= "dpll_iva_m5x2_ck",
@@ -5362,7 +5362,7 @@
 };
 
 /* l3_main_2 -> sl2if */
-static struct omap_hwmod_ocp_if omap44xx_l3_main_2__sl2if = {
+static struct omap_hwmod_ocp_if __maybe_unused omap44xx_l3_main_2__sl2if = {
 	.master		= &omap44xx_l3_main_2_hwmod,
 	.slave		= &omap44xx_sl2if_hwmod,
 	.clk		= "l3_div_ck",
@@ -6032,7 +6032,7 @@
 	&omap44xx_l4_abe__dmic,
 	&omap44xx_l4_abe__dmic_dma,
 	&omap44xx_dsp__iva,
-	&omap44xx_dsp__sl2if,
+	/* &omap44xx_dsp__sl2if, */
 	&omap44xx_l4_cfg__dsp,
 	&omap44xx_l3_main_2__dss,
 	&omap44xx_l4_per__dss,
@@ -6068,7 +6068,7 @@
 	&omap44xx_l4_per__i2c4,
 	&omap44xx_l3_main_2__ipu,
 	&omap44xx_l3_main_2__iss,
-	&omap44xx_iva__sl2if,
+	/* &omap44xx_iva__sl2if, */
 	&omap44xx_l3_main_2__iva,
 	&omap44xx_l4_wkup__kbd,
 	&omap44xx_l4_cfg__mailbox,
@@ -6099,7 +6099,7 @@
 	&omap44xx_l4_cfg__cm_core,
 	&omap44xx_l4_wkup__prm,
 	&omap44xx_l4_wkup__scrm,
-	&omap44xx_l3_main_2__sl2if,
+	/* &omap44xx_l3_main_2__sl2if, */
 	&omap44xx_l4_abe__slimbus1,
 	&omap44xx_l4_abe__slimbus1_dma,
 	&omap44xx_l4_per__slimbus2,
diff --git a/arch/arm/mach-omap2/timer.c b/arch/arm/mach-omap2/timer.c
index 2ff6d41..2ba4f57 100644
--- a/arch/arm/mach-omap2/timer.c
+++ b/arch/arm/mach-omap2/timer.c
@@ -260,6 +260,7 @@
 	return 0;
 }
 
+#ifdef CONFIG_OMAP_32K_TIMER
 /* Setup free-running counter for clocksource */
 static int __init omap2_sync32k_clocksource_init(void)
 {
@@ -299,6 +300,12 @@
 
 	return ret;
 }
+#else
+static inline int omap2_sync32k_clocksource_init(void)
+{
+	return -ENODEV;
+}
+#endif
 
 static void __init omap2_gptimer_clocksource_init(int gptimer_id,
 						const char *fck_source)
diff --git a/arch/arm/mach-shmobile/board-armadillo800eva.c b/arch/arm/mach-shmobile/board-armadillo800eva.c
index cf10f92..453a6e5 100644
--- a/arch/arm/mach-shmobile/board-armadillo800eva.c
+++ b/arch/arm/mach-shmobile/board-armadillo800eva.c
@@ -520,13 +520,14 @@
 };
 
 /* GPIO KEY */
-#define GPIO_KEY(c, g, d) { .code = c, .gpio = g, .desc = d, .active_low = 1 }
+#define GPIO_KEY(c, g, d, ...) \
+	{ .code = c, .gpio = g, .desc = d, .active_low = 1, __VA_ARGS__ }
 
 static struct gpio_keys_button gpio_buttons[] = {
-	GPIO_KEY(KEY_POWER,	GPIO_PORT99,	"SW1"),
-	GPIO_KEY(KEY_BACK,	GPIO_PORT100,	"SW2"),
-	GPIO_KEY(KEY_MENU,	GPIO_PORT97,	"SW3"),
-	GPIO_KEY(KEY_HOME,	GPIO_PORT98,	"SW4"),
+	GPIO_KEY(KEY_POWER,	GPIO_PORT99,	"SW3", .wakeup = 1),
+	GPIO_KEY(KEY_BACK,	GPIO_PORT100,	"SW4"),
+	GPIO_KEY(KEY_MENU,	GPIO_PORT97,	"SW5"),
+	GPIO_KEY(KEY_HOME,	GPIO_PORT98,	"SW6"),
 };
 
 static struct gpio_keys_platform_data gpio_key_info = {
@@ -901,8 +902,8 @@
 	&camera_device,
 	&ceu0_device,
 	&fsi_device,
-	&fsi_hdmi_device,
 	&fsi_wm8978_device,
+	&fsi_hdmi_device,
 };
 
 static void __init eva_clock_init(void)
diff --git a/arch/arm/mach-shmobile/board-mackerel.c b/arch/arm/mach-shmobile/board-mackerel.c
index 7ea2b31..c129542 100644
--- a/arch/arm/mach-shmobile/board-mackerel.c
+++ b/arch/arm/mach-shmobile/board-mackerel.c
@@ -695,6 +695,7 @@
  *  - J30 "open"
  *  - modify usbhs1_get_id() USBHS_HOST -> USBHS_GADGET
  *  - add .get_vbus = usbhs_get_vbus in usbhs1_private
+ *  - check usbhs0_device(pio)/usbhs1_device(irq) order in mackerel_devices.
  */
 #define IRQ8 evt2irq(0x0300)
 #define USB_PHY_MODE		(1 << 4)
@@ -1325,8 +1326,8 @@
 	&nor_flash_device,
 	&smc911x_device,
 	&lcdc_device,
-	&usbhs1_device,
 	&usbhs0_device,
+	&usbhs1_device,
 	&leds_device,
 	&fsi_device,
 	&fsi_ak4643_device,
diff --git a/arch/arm/mach-shmobile/board-marzen.c b/arch/arm/mach-shmobile/board-marzen.c
index 3a528cf..fcf5a47 100644
--- a/arch/arm/mach-shmobile/board-marzen.c
+++ b/arch/arm/mach-shmobile/board-marzen.c
@@ -67,7 +67,7 @@
 
 static struct platform_device eth_device = {
 	.name		= "smsc911x",
-	.id		= 0,
+	.id		= -1,
 	.dev  = {
 		.platform_data = &smsc911x_platdata,
 	},
diff --git a/arch/arm/mach-shmobile/intc-sh73a0.c b/arch/arm/mach-shmobile/intc-sh73a0.c
index ee44740..588555a 100644
--- a/arch/arm/mach-shmobile/intc-sh73a0.c
+++ b/arch/arm/mach-shmobile/intc-sh73a0.c
@@ -259,9 +259,9 @@
 	return 0; /* always allow wakeup */
 }
 
-#define RELOC_BASE 0x1000
+#define RELOC_BASE 0x1200
 
-/* INTCA IRQ pins at INTCS + 0x1000 to make space for GIC+INTC handling */
+/* INTCA IRQ pins at INTCS + RELOC_BASE to make space for GIC+INTC handling */
 #define INTCS_VECT_RELOC(n, vect) INTCS_VECT((n), (vect) + RELOC_BASE)
 
 INTC_IRQ_PINS_32(intca_irq_pins, 0xe6900000,
diff --git a/arch/arm/mm/context.c b/arch/arm/mm/context.c
index 119bc52..4e07eec 100644
--- a/arch/arm/mm/context.c
+++ b/arch/arm/mm/context.c
@@ -63,10 +63,11 @@
 	pid = task_pid_nr(thread->task) << ASID_BITS;
 	asm volatile(
 	"	mrc	p15, 0, %0, c13, c0, 1\n"
-	"	bfi	%1, %0, #0, %2\n"
-	"	mcr	p15, 0, %1, c13, c0, 1\n"
+	"	and	%0, %0, %2\n"
+	"	orr	%0, %0, %1\n"
+	"	mcr	p15, 0, %0, c13, c0, 1\n"
 	: "=r" (contextidr), "+r" (pid)
-	: "I" (ASID_BITS));
+	: "I" (~ASID_MASK));
 	isb();
 
 	return NOTIFY_OK;
diff --git a/arch/arm/mm/dma-mapping.c b/arch/arm/mm/dma-mapping.c
index 4e7d118..e59c4ab 100644
--- a/arch/arm/mm/dma-mapping.c
+++ b/arch/arm/mm/dma-mapping.c
@@ -267,17 +267,19 @@
 	vunmap(cpu_addr);
 }
 
+#define DEFAULT_DMA_COHERENT_POOL_SIZE	SZ_256K
+
 struct dma_pool {
 	size_t size;
 	spinlock_t lock;
 	unsigned long *bitmap;
 	unsigned long nr_pages;
 	void *vaddr;
-	struct page *page;
+	struct page **pages;
 };
 
 static struct dma_pool atomic_pool = {
-	.size = SZ_256K,
+	.size = DEFAULT_DMA_COHERENT_POOL_SIZE,
 };
 
 static int __init early_coherent_pool(char *p)
@@ -287,6 +289,21 @@
 }
 early_param("coherent_pool", early_coherent_pool);
 
+void __init init_dma_coherent_pool_size(unsigned long size)
+{
+	/*
+	 * Catch any attempt to set the pool size too late.
+	 */
+	BUG_ON(atomic_pool.vaddr);
+
+	/*
+	 * Set architecture specific coherent pool size only if
+	 * it has not been changed by kernel command line parameter.
+	 */
+	if (atomic_pool.size == DEFAULT_DMA_COHERENT_POOL_SIZE)
+		atomic_pool.size = size;
+}
+
 /*
  * Initialise the coherent pool for atomic allocations.
  */
@@ -297,6 +314,7 @@
 	unsigned long nr_pages = pool->size >> PAGE_SHIFT;
 	unsigned long *bitmap;
 	struct page *page;
+	struct page **pages;
 	void *ptr;
 	int bitmap_size = BITS_TO_LONGS(nr_pages) * sizeof(long);
 
@@ -304,21 +322,31 @@
 	if (!bitmap)
 		goto no_bitmap;
 
+	pages = kzalloc(nr_pages * sizeof(struct page *), GFP_KERNEL);
+	if (!pages)
+		goto no_pages;
+
 	if (IS_ENABLED(CONFIG_CMA))
 		ptr = __alloc_from_contiguous(NULL, pool->size, prot, &page);
 	else
 		ptr = __alloc_remap_buffer(NULL, pool->size, GFP_KERNEL, prot,
 					   &page, NULL);
 	if (ptr) {
+		int i;
+
+		for (i = 0; i < nr_pages; i++)
+			pages[i] = page + i;
+
 		spin_lock_init(&pool->lock);
 		pool->vaddr = ptr;
-		pool->page = page;
+		pool->pages = pages;
 		pool->bitmap = bitmap;
 		pool->nr_pages = nr_pages;
 		pr_info("DMA: preallocated %u KiB pool for atomic coherent allocations\n",
 		       (unsigned)pool->size / 1024);
 		return 0;
 	}
+no_pages:
 	kfree(bitmap);
 no_bitmap:
 	pr_err("DMA: failed to allocate %u KiB pool for atomic coherent allocation\n",
@@ -443,27 +471,45 @@
 	if (pageno < pool->nr_pages) {
 		bitmap_set(pool->bitmap, pageno, count);
 		ptr = pool->vaddr + PAGE_SIZE * pageno;
-		*ret_page = pool->page + pageno;
+		*ret_page = pool->pages[pageno];
+	} else {
+		pr_err_once("ERROR: %u KiB atomic DMA coherent pool is too small!\n"
+			    "Please increase it with coherent_pool= kernel parameter!\n",
+			    (unsigned)pool->size / 1024);
 	}
 	spin_unlock_irqrestore(&pool->lock, flags);
 
 	return ptr;
 }
 
+static bool __in_atomic_pool(void *start, size_t size)
+{
+	struct dma_pool *pool = &atomic_pool;
+	void *end = start + size;
+	void *pool_start = pool->vaddr;
+	void *pool_end = pool->vaddr + pool->size;
+
+	if (start < pool_start || start >= pool_end)
+		return false;
+
+	if (end <= pool_end)
+		return true;
+
+	WARN(1, "Wrong coherent size(%p-%p) from atomic pool(%p-%p)\n",
+	     start, end - 1, pool_start, pool_end - 1);
+
+	return false;
+}
+
 static int __free_from_pool(void *start, size_t size)
 {
 	struct dma_pool *pool = &atomic_pool;
 	unsigned long pageno, count;
 	unsigned long flags;
 
-	if (start < pool->vaddr || start > pool->vaddr + pool->size)
+	if (!__in_atomic_pool(start, size))
 		return 0;
 
-	if (start + size > pool->vaddr + pool->size) {
-		WARN(1, "freeing wrong coherent size from pool\n");
-		return 0;
-	}
-
 	pageno = (start - pool->vaddr) >> PAGE_SHIFT;
 	count = size >> PAGE_SHIFT;
 
@@ -1090,10 +1136,22 @@
 	return 0;
 }
 
+static struct page **__atomic_get_pages(void *addr)
+{
+	struct dma_pool *pool = &atomic_pool;
+	struct page **pages = pool->pages;
+	int offs = (addr - pool->vaddr) >> PAGE_SHIFT;
+
+	return pages + offs;
+}
+
 static struct page **__iommu_get_pages(void *cpu_addr, struct dma_attrs *attrs)
 {
 	struct vm_struct *area;
 
+	if (__in_atomic_pool(cpu_addr, PAGE_SIZE))
+		return __atomic_get_pages(cpu_addr);
+
 	if (dma_get_attr(DMA_ATTR_NO_KERNEL_MAPPING, attrs))
 		return cpu_addr;
 
@@ -1103,6 +1161,34 @@
 	return NULL;
 }
 
+static void *__iommu_alloc_atomic(struct device *dev, size_t size,
+				  dma_addr_t *handle)
+{
+	struct page *page;
+	void *addr;
+
+	addr = __alloc_from_pool(size, &page);
+	if (!addr)
+		return NULL;
+
+	*handle = __iommu_create_mapping(dev, &page, size);
+	if (*handle == DMA_ERROR_CODE)
+		goto err_mapping;
+
+	return addr;
+
+err_mapping:
+	__free_from_pool(addr, size);
+	return NULL;
+}
+
+static void __iommu_free_atomic(struct device *dev, struct page **pages,
+				dma_addr_t handle, size_t size)
+{
+	__iommu_remove_mapping(dev, handle, size);
+	__free_from_pool(page_address(pages[0]), size);
+}
+
 static void *arm_iommu_alloc_attrs(struct device *dev, size_t size,
 	    dma_addr_t *handle, gfp_t gfp, struct dma_attrs *attrs)
 {
@@ -1113,6 +1199,9 @@
 	*handle = DMA_ERROR_CODE;
 	size = PAGE_ALIGN(size);
 
+	if (gfp & GFP_ATOMIC)
+		return __iommu_alloc_atomic(dev, size, handle);
+
 	pages = __iommu_alloc_buffer(dev, size, gfp);
 	if (!pages)
 		return NULL;
@@ -1179,6 +1268,11 @@
 		return;
 	}
 
+	if (__in_atomic_pool(cpu_addr, size)) {
+		__iommu_free_atomic(dev, pages, handle, size);
+		return;
+	}
+
 	if (!dma_get_attr(DMA_ATTR_NO_KERNEL_MAPPING, attrs)) {
 		unmap_kernel_range((unsigned long)cpu_addr, size);
 		vunmap(cpu_addr);
diff --git a/arch/arm/mm/mm.h b/arch/arm/mm/mm.h
index 6776160..a8ee92d 100644
--- a/arch/arm/mm/mm.h
+++ b/arch/arm/mm/mm.h
@@ -55,6 +55,9 @@
 /* permanent static mappings from iotable_init() */
 #define VM_ARM_STATIC_MAPPING	0x40000000
 
+/* empty mapping */
+#define VM_ARM_EMPTY_MAPPING	0x20000000
+
 /* mapping type (attributes) for permanent static mappings */
 #define VM_ARM_MTYPE(mt)		((mt) << 20)
 #define VM_ARM_MTYPE_MASK	(0x1f << 20)
diff --git a/arch/arm/mm/mmu.c b/arch/arm/mm/mmu.c
index 4c2d045..c2fa21d 100644
--- a/arch/arm/mm/mmu.c
+++ b/arch/arm/mm/mmu.c
@@ -807,7 +807,7 @@
 	vm = early_alloc_aligned(sizeof(*vm), __alignof__(*vm));
 	vm->addr = (void *)addr;
 	vm->size = SECTION_SIZE;
-	vm->flags = VM_IOREMAP | VM_ARM_STATIC_MAPPING;
+	vm->flags = VM_IOREMAP | VM_ARM_EMPTY_MAPPING;
 	vm->caller = pmd_empty_section_gap;
 	vm_area_add_early(vm);
 }
@@ -820,7 +820,7 @@
 
 	/* we're still single threaded hence no lock needed here */
 	for (vm = vmlist; vm; vm = vm->next) {
-		if (!(vm->flags & VM_ARM_STATIC_MAPPING))
+		if (!(vm->flags & (VM_ARM_STATIC_MAPPING | VM_ARM_EMPTY_MAPPING)))
 			continue;
 		addr = (unsigned long)vm->addr;
 		if (addr < next)
@@ -961,8 +961,8 @@
 		 * Check whether this memory bank would partially overlap
 		 * the vmalloc area.
 		 */
-		if (__va(bank->start + bank->size) > vmalloc_min ||
-		    __va(bank->start + bank->size) < __va(bank->start)) {
+		if (__va(bank->start + bank->size - 1) >= vmalloc_min ||
+		    __va(bank->start + bank->size - 1) <= __va(bank->start)) {
 			unsigned long newsize = vmalloc_min - __va(bank->start);
 			printk(KERN_NOTICE "Truncating RAM at %.8llx-%.8llx "
 			       "to -%.8llx (vmalloc region overlap).\n",
diff --git a/arch/arm/plat-omap/sram.c b/arch/arm/plat-omap/sram.c
index 766181c..024f3b0 100644
--- a/arch/arm/plat-omap/sram.c
+++ b/arch/arm/plat-omap/sram.c
@@ -68,6 +68,7 @@
 
 static unsigned long omap_sram_start;
 static void __iomem *omap_sram_base;
+static unsigned long omap_sram_skip;
 static unsigned long omap_sram_size;
 static void __iomem *omap_sram_ceil;
 
@@ -106,6 +107,7 @@
  */
 static void __init omap_detect_sram(void)
 {
+	omap_sram_skip = SRAM_BOOTLOADER_SZ;
 	if (cpu_class_is_omap2()) {
 		if (is_sram_locked()) {
 			if (cpu_is_omap34xx()) {
@@ -113,6 +115,7 @@
 				if ((omap_type() == OMAP2_DEVICE_TYPE_EMU) ||
 				    (omap_type() == OMAP2_DEVICE_TYPE_SEC)) {
 					omap_sram_size = 0x7000; /* 28K */
+					omap_sram_skip += SZ_16K;
 				} else {
 					omap_sram_size = 0x8000; /* 32K */
 				}
@@ -175,8 +178,10 @@
 		return;
 
 #ifdef CONFIG_OMAP4_ERRATA_I688
+	if (cpu_is_omap44xx()) {
 		omap_sram_start += PAGE_SIZE;
 		omap_sram_size -= SZ_16K;
+	}
 #endif
 	if (cpu_is_omap34xx()) {
 		/*
@@ -203,8 +208,8 @@
 	 * Looks like we need to preserve some bootloader code at the
 	 * beginning of SRAM for jumping to flash for reboot to work...
 	 */
-	memset_io(omap_sram_base + SRAM_BOOTLOADER_SZ, 0,
-		  omap_sram_size - SRAM_BOOTLOADER_SZ);
+	memset_io(omap_sram_base + omap_sram_skip, 0,
+		  omap_sram_size - omap_sram_skip);
 }
 
 /*
@@ -218,7 +223,7 @@
 {
 	unsigned long available, new_ceil = (unsigned long)omap_sram_ceil;
 
-	available = omap_sram_ceil - (omap_sram_base + SRAM_BOOTLOADER_SZ);
+	available = omap_sram_ceil - (omap_sram_base + omap_sram_skip);
 
 	if (size > available) {
 		pr_err("Not enough space in SRAM\n");
diff --git a/arch/blackfin/Kconfig b/arch/blackfin/Kconfig
index f348619..c7092e6 100644
--- a/arch/blackfin/Kconfig
+++ b/arch/blackfin/Kconfig
@@ -38,6 +38,7 @@
 	select GENERIC_ATOMIC64
 	select GENERIC_IRQ_PROBE
 	select IRQ_PER_CPU if SMP
+	select USE_GENERIC_SMP_HELPERS if SMP
 	select HAVE_NMI_WATCHDOG if NMI_WATCHDOG
 	select GENERIC_SMP_IDLE_THREAD
 	select ARCH_USES_GETTIMEOFFSET if !GENERIC_CLOCKEVENTS
diff --git a/arch/blackfin/Makefile b/arch/blackfin/Makefile
index d3d7e64..66cf000 100644
--- a/arch/blackfin/Makefile
+++ b/arch/blackfin/Makefile
@@ -20,7 +20,6 @@
 KBUILD_AFLAGS           += $(call cc-option,-mno-fdpic)
 KBUILD_CFLAGS_MODULE    += -mlong-calls
 LDFLAGS                 += -m elf32bfin
-KALLSYMS         += --symbol-prefix=_
 
 KBUILD_DEFCONFIG := BF537-STAMP_defconfig
 
diff --git a/arch/blackfin/include/asm/smp.h b/arch/blackfin/include/asm/smp.h
index dc3d144..9631598 100644
--- a/arch/blackfin/include/asm/smp.h
+++ b/arch/blackfin/include/asm/smp.h
@@ -18,6 +18,8 @@
 #define raw_smp_processor_id()  blackfin_core_id()
 
 extern void bfin_relocate_coreb_l1_mem(void);
+extern void arch_send_call_function_single_ipi(int cpu);
+extern void arch_send_call_function_ipi_mask(const struct cpumask *mask);
 
 #if defined(CONFIG_SMP) && defined(CONFIG_ICACHE_FLUSH_L1)
 asmlinkage void blackfin_icache_flush_range_l1(unsigned long *ptr);
diff --git a/arch/blackfin/mach-common/smp.c b/arch/blackfin/mach-common/smp.c
index 00bbe67..a401513 100644
--- a/arch/blackfin/mach-common/smp.c
+++ b/arch/blackfin/mach-common/smp.c
@@ -48,10 +48,13 @@
 
 struct blackfin_initial_pda __cpuinitdata initial_pda_coreb;
 
-#define BFIN_IPI_TIMER	      0
-#define BFIN_IPI_RESCHEDULE   1
-#define BFIN_IPI_CALL_FUNC    2
-#define BFIN_IPI_CPU_STOP     3
+enum ipi_message_type {
+	BFIN_IPI_TIMER,
+	BFIN_IPI_RESCHEDULE,
+	BFIN_IPI_CALL_FUNC,
+	BFIN_IPI_CALL_FUNC_SINGLE,
+	BFIN_IPI_CPU_STOP,
+};
 
 struct blackfin_flush_data {
 	unsigned long start;
@@ -60,35 +63,20 @@
 
 void *secondary_stack;
 
-
-struct smp_call_struct {
-	void (*func)(void *info);
-	void *info;
-	int wait;
-	cpumask_t *waitmask;
-};
-
 static struct blackfin_flush_data smp_flush_data;
 
 static DEFINE_SPINLOCK(stop_lock);
 
-struct ipi_message {
-	unsigned long type;
-	struct smp_call_struct call_struct;
-};
-
 /* A magic number - stress test shows this is safe for common cases */
 #define BFIN_IPI_MSGQ_LEN 5
 
 /* Simple FIFO buffer, overflow leads to panic */
-struct ipi_message_queue {
-	spinlock_t lock;
+struct ipi_data {
 	unsigned long count;
-	unsigned long head; /* head of the queue */
-	struct ipi_message ipi_message[BFIN_IPI_MSGQ_LEN];
+	unsigned long bits;
 };
 
-static DEFINE_PER_CPU(struct ipi_message_queue, ipi_msg_queue);
+static DEFINE_PER_CPU(struct ipi_data, bfin_ipi);
 
 static void ipi_cpu_stop(unsigned int cpu)
 {
@@ -129,28 +117,6 @@
 	blackfin_icache_flush_range(fdata->start, fdata->end);
 }
 
-static void ipi_call_function(unsigned int cpu, struct ipi_message *msg)
-{
-	int wait;
-	void (*func)(void *info);
-	void *info;
-	func = msg->call_struct.func;
-	info = msg->call_struct.info;
-	wait = msg->call_struct.wait;
-	func(info);
-	if (wait) {
-#ifdef __ARCH_SYNC_CORE_DCACHE
-		/*
-		 * 'wait' usually means synchronization between CPUs.
-		 * Invalidate D cache in case shared data was changed
-		 * by func() to ensure cache coherence.
-		 */
-		resync_core_dcache();
-#endif
-		cpumask_clear_cpu(cpu, msg->call_struct.waitmask);
-	}
-}
-
 /* Use IRQ_SUPPLE_0 to request reschedule.
  * When returning from interrupt to user space,
  * there is chance to reschedule */
@@ -172,152 +138,95 @@
 
 static irqreturn_t ipi_handler_int1(int irq, void *dev_instance)
 {
-	struct ipi_message *msg;
-	struct ipi_message_queue *msg_queue;
+	struct ipi_data *bfin_ipi_data;
 	unsigned int cpu = smp_processor_id();
-	unsigned long flags;
+	unsigned long pending;
+	unsigned long msg;
 
 	platform_clear_ipi(cpu, IRQ_SUPPLE_1);
 
-	msg_queue = &__get_cpu_var(ipi_msg_queue);
+	bfin_ipi_data = &__get_cpu_var(bfin_ipi);
 
-	spin_lock_irqsave(&msg_queue->lock, flags);
+	while ((pending = xchg(&bfin_ipi_data->bits, 0)) != 0) {
+		msg = 0;
+		do {
+			msg = find_next_bit(&pending, BITS_PER_LONG, msg + 1);
+			switch (msg) {
+			case BFIN_IPI_TIMER:
+				ipi_timer();
+				break;
+			case BFIN_IPI_RESCHEDULE:
+				scheduler_ipi();
+				break;
+			case BFIN_IPI_CALL_FUNC:
+				generic_smp_call_function_interrupt();
+				break;
 
-	while (msg_queue->count) {
-		msg = &msg_queue->ipi_message[msg_queue->head];
-		switch (msg->type) {
-		case BFIN_IPI_TIMER:
-			ipi_timer();
-			break;
-		case BFIN_IPI_RESCHEDULE:
-			scheduler_ipi();
-			break;
-		case BFIN_IPI_CALL_FUNC:
-			ipi_call_function(cpu, msg);
-			break;
-		case BFIN_IPI_CPU_STOP:
-			ipi_cpu_stop(cpu);
-			break;
-		default:
-			printk(KERN_CRIT "CPU%u: Unknown IPI message 0x%lx\n",
-			       cpu, msg->type);
-			break;
-		}
-		msg_queue->head++;
-		msg_queue->head %= BFIN_IPI_MSGQ_LEN;
-		msg_queue->count--;
+			case BFIN_IPI_CALL_FUNC_SINGLE:
+				generic_smp_call_function_single_interrupt();
+				break;
+
+			case BFIN_IPI_CPU_STOP:
+				ipi_cpu_stop(cpu);
+				break;
+			}
+		} while (msg < BITS_PER_LONG);
+
+		smp_mb();
 	}
-	spin_unlock_irqrestore(&msg_queue->lock, flags);
 	return IRQ_HANDLED;
 }
 
-static void ipi_queue_init(void)
+static void bfin_ipi_init(void)
 {
 	unsigned int cpu;
-	struct ipi_message_queue *msg_queue;
+	struct ipi_data *bfin_ipi_data;
 	for_each_possible_cpu(cpu) {
-		msg_queue = &per_cpu(ipi_msg_queue, cpu);
-		spin_lock_init(&msg_queue->lock);
-		msg_queue->count = 0;
-		msg_queue->head = 0;
+		bfin_ipi_data = &per_cpu(bfin_ipi, cpu);
+		bfin_ipi_data->bits = 0;
+		bfin_ipi_data->count = 0;
 	}
 }
 
-static inline void smp_send_message(cpumask_t callmap, unsigned long type,
-					void (*func) (void *info), void *info, int wait)
+void send_ipi(const struct cpumask *cpumask, enum ipi_message_type msg)
 {
 	unsigned int cpu;
-	struct ipi_message_queue *msg_queue;
-	struct ipi_message *msg;
-	unsigned long flags, next_msg;
-	cpumask_t waitmask; /* waitmask is shared by all cpus */
+	struct ipi_data *bfin_ipi_data;
+	unsigned long flags;
 
-	cpumask_copy(&waitmask, &callmap);
-	for_each_cpu(cpu, &callmap) {
-		msg_queue = &per_cpu(ipi_msg_queue, cpu);
-		spin_lock_irqsave(&msg_queue->lock, flags);
-		if (msg_queue->count < BFIN_IPI_MSGQ_LEN) {
-			next_msg = (msg_queue->head + msg_queue->count)
-					% BFIN_IPI_MSGQ_LEN;
-			msg = &msg_queue->ipi_message[next_msg];
-			msg->type = type;
-			if (type == BFIN_IPI_CALL_FUNC) {
-				msg->call_struct.func = func;
-				msg->call_struct.info = info;
-				msg->call_struct.wait = wait;
-				msg->call_struct.waitmask = &waitmask;
-			}
-			msg_queue->count++;
-		} else
-			panic("IPI message queue overflow\n");
-		spin_unlock_irqrestore(&msg_queue->lock, flags);
+	local_irq_save(flags);
+
+	for_each_cpu(cpu, cpumask) {
+		bfin_ipi_data = &per_cpu(bfin_ipi, cpu);
+		smp_mb();
+		set_bit(msg, &bfin_ipi_data->bits);
+		bfin_ipi_data->count++;
 		platform_send_ipi_cpu(cpu, IRQ_SUPPLE_1);
 	}
 
-	if (wait) {
-		while (!cpumask_empty(&waitmask))
-			blackfin_dcache_invalidate_range(
-				(unsigned long)(&waitmask),
-				(unsigned long)(&waitmask));
-#ifdef __ARCH_SYNC_CORE_DCACHE
-		/*
-		 * Invalidate D cache in case shared data was changed by
-		 * other processors to ensure cache coherence.
-		 */
-		resync_core_dcache();
-#endif
-	}
+	local_irq_restore(flags);
 }
 
-int smp_call_function(void (*func)(void *info), void *info, int wait)
+void arch_send_call_function_single_ipi(int cpu)
 {
-	cpumask_t callmap;
-
-	preempt_disable();
-	cpumask_copy(&callmap, cpu_online_mask);
-	cpumask_clear_cpu(smp_processor_id(), &callmap);
-	if (!cpumask_empty(&callmap))
-		smp_send_message(callmap, BFIN_IPI_CALL_FUNC, func, info, wait);
-
-	preempt_enable();
-
-	return 0;
+	send_ipi(cpumask_of(cpu), BFIN_IPI_CALL_FUNC_SINGLE);
 }
-EXPORT_SYMBOL_GPL(smp_call_function);
 
-int smp_call_function_single(int cpuid, void (*func) (void *info), void *info,
-				int wait)
+void arch_send_call_function_ipi_mask(const struct cpumask *mask)
 {
-	unsigned int cpu = cpuid;
-	cpumask_t callmap;
-
-	if (cpu_is_offline(cpu))
-		return 0;
-	cpumask_clear(&callmap);
-	cpumask_set_cpu(cpu, &callmap);
-
-	smp_send_message(callmap, BFIN_IPI_CALL_FUNC, func, info, wait);
-
-	return 0;
+	send_ipi(mask, BFIN_IPI_CALL_FUNC);
 }
-EXPORT_SYMBOL_GPL(smp_call_function_single);
 
 void smp_send_reschedule(int cpu)
 {
-	cpumask_t callmap;
-	/* simply trigger an ipi */
-
-	cpumask_clear(&callmap);
-	cpumask_set_cpu(cpu, &callmap);
-
-	smp_send_message(callmap, BFIN_IPI_RESCHEDULE, NULL, NULL, 0);
+	send_ipi(cpumask_of(cpu), BFIN_IPI_RESCHEDULE);
 
 	return;
 }
 
 void smp_send_msg(const struct cpumask *mask, unsigned long type)
 {
-	smp_send_message(*mask, type, NULL, NULL, 0);
+	send_ipi(mask, type);
 }
 
 void smp_timer_broadcast(const struct cpumask *mask)
@@ -333,7 +242,7 @@
 	cpumask_copy(&callmap, cpu_online_mask);
 	cpumask_clear_cpu(smp_processor_id(), &callmap);
 	if (!cpumask_empty(&callmap))
-		smp_send_message(callmap, BFIN_IPI_CPU_STOP, NULL, NULL, 0);
+		send_ipi(&callmap, BFIN_IPI_CPU_STOP);
 
 	preempt_enable();
 
@@ -436,7 +345,7 @@
 void __init smp_prepare_cpus(unsigned int max_cpus)
 {
 	platform_prepare_cpus(max_cpus);
-	ipi_queue_init();
+	bfin_ipi_init();
 	platform_request_ipi(IRQ_SUPPLE_0, ipi_handler_int0);
 	platform_request_ipi(IRQ_SUPPLE_1, ipi_handler_int1);
 }
diff --git a/arch/powerpc/include/asm/processor.h b/arch/powerpc/include/asm/processor.h
index 53b6dfa..54b73a2 100644
--- a/arch/powerpc/include/asm/processor.h
+++ b/arch/powerpc/include/asm/processor.h
@@ -386,6 +386,7 @@
 enum idle_boot_override {IDLE_NO_OVERRIDE = 0, IDLE_POWERSAVE_OFF};
 
 extern int powersave_nap;	/* set if nap mode can be used in idle loop */
+extern void power7_nap(void);
 
 #ifdef CONFIG_PSERIES_IDLE
 extern void update_smt_snooze_delay(int snooze);
diff --git a/arch/powerpc/kernel/asm-offsets.c b/arch/powerpc/kernel/asm-offsets.c
index 85b05c4..e899572 100644
--- a/arch/powerpc/kernel/asm-offsets.c
+++ b/arch/powerpc/kernel/asm-offsets.c
@@ -76,6 +76,7 @@
 	DEFINE(SIGSEGV, SIGSEGV);
 	DEFINE(NMI_MASK, NMI_MASK);
 	DEFINE(THREAD_DSCR, offsetof(struct thread_struct, dscr));
+	DEFINE(THREAD_DSCR_INHERIT, offsetof(struct thread_struct, dscr_inherit));
 #else
 	DEFINE(THREAD_INFO, offsetof(struct task_struct, stack));
 #endif /* CONFIG_PPC64 */
diff --git a/arch/powerpc/kernel/dbell.c b/arch/powerpc/kernel/dbell.c
index 5b25c80..a892680 100644
--- a/arch/powerpc/kernel/dbell.c
+++ b/arch/powerpc/kernel/dbell.c
@@ -28,6 +28,8 @@
 
 void doorbell_cause_ipi(int cpu, unsigned long data)
 {
+	/* Order previous accesses vs. msgsnd, which is treated as a store */
+	mb();
 	ppc_msgsnd(PPC_DBELL, 0, data);
 }
 
diff --git a/arch/powerpc/kernel/entry_64.S b/arch/powerpc/kernel/entry_64.S
index 4b01a25..b40e0b4 100644
--- a/arch/powerpc/kernel/entry_64.S
+++ b/arch/powerpc/kernel/entry_64.S
@@ -370,6 +370,12 @@
 	li	r3,0
 	b	syscall_exit
 
+	.section	".toc","aw"
+DSCR_DEFAULT:
+	.tc dscr_default[TC],dscr_default
+
+	.section	".text"
+
 /*
  * This routine switches between two different tasks.  The process
  * state of one is saved on its kernel stack.  Then the state
@@ -509,9 +515,6 @@
 	mr	r1,r8		/* start using new stack pointer */
 	std	r7,PACAKSAVE(r13)
 
-	ld	r6,_CCR(r1)
-	mtcrf	0xFF,r6
-
 #ifdef CONFIG_ALTIVEC
 BEGIN_FTR_SECTION
 	ld	r0,THREAD_VRSAVE(r4)
@@ -520,14 +523,22 @@
 #endif /* CONFIG_ALTIVEC */
 #ifdef CONFIG_PPC64
 BEGIN_FTR_SECTION
+	lwz	r6,THREAD_DSCR_INHERIT(r4)
+	ld	r7,DSCR_DEFAULT@toc(2)
 	ld	r0,THREAD_DSCR(r4)
-	cmpd	r0,r25
-	beq	1f
+	cmpwi	r6,0
+	bne	1f
+	ld	r0,0(r7)
+1:	cmpd	r0,r25
+	beq	2f
 	mtspr	SPRN_DSCR,r0
-1:	
+2:
 END_FTR_SECTION_IFSET(CPU_FTR_DSCR)
 #endif
 
+	ld	r6,_CCR(r1)
+	mtcrf	0xFF,r6
+
 	/* r3-r13 are destroyed -- Cort */
 	REST_8GPRS(14, r1)
 	REST_10GPRS(22, r1)
diff --git a/arch/powerpc/kernel/exceptions-64s.S b/arch/powerpc/kernel/exceptions-64s.S
index e894515..39aa97d 100644
--- a/arch/powerpc/kernel/exceptions-64s.S
+++ b/arch/powerpc/kernel/exceptions-64s.S
@@ -186,7 +186,7 @@
 	KVM_HANDLER_PR(PACA_EXGEN, EXC_STD, 0x800)
 
 	MASKABLE_EXCEPTION_PSERIES(0x900, 0x900, decrementer)
-	MASKABLE_EXCEPTION_HV(0x980, 0x982, decrementer)
+	STD_EXCEPTION_HV(0x980, 0x982, hdecrementer)
 
 	STD_EXCEPTION_PSERIES(0xa00, 0xa00, trap_0a)
 	KVM_HANDLER_PR(PACA_EXGEN, EXC_STD, 0xa00)
@@ -486,6 +486,7 @@
 
 	STD_EXCEPTION_COMMON_ASYNC(0x500, hardware_interrupt, do_IRQ)
 	STD_EXCEPTION_COMMON_ASYNC(0x900, decrementer, .timer_interrupt)
+	STD_EXCEPTION_COMMON(0x980, hdecrementer, .hdec_interrupt)
 	STD_EXCEPTION_COMMON(0xa00, trap_0a, .unknown_exception)
 	STD_EXCEPTION_COMMON(0xb00, trap_0b, .unknown_exception)
 	STD_EXCEPTION_COMMON(0xd00, single_step, .single_step_exception)
diff --git a/arch/powerpc/kernel/idle_power7.S b/arch/powerpc/kernel/idle_power7.S
index 7140d83..e11863f 100644
--- a/arch/powerpc/kernel/idle_power7.S
+++ b/arch/powerpc/kernel/idle_power7.S
@@ -28,7 +28,9 @@
 	lwz	r4,ADDROFF(powersave_nap)(r3)
 	cmpwi	0,r4,0
 	beqlr
+	/* fall through */
 
+_GLOBAL(power7_nap)
 	/* NAP is a state loss, we create a regs frame on the
 	 * stack, fill it up with the state we care about and
 	 * stick a pointer to it in PACAR1. We really only
diff --git a/arch/powerpc/kernel/process.c b/arch/powerpc/kernel/process.c
index 710f400..1a1f2dd 100644
--- a/arch/powerpc/kernel/process.c
+++ b/arch/powerpc/kernel/process.c
@@ -802,16 +802,8 @@
 #endif /* CONFIG_PPC_STD_MMU_64 */
 #ifdef CONFIG_PPC64 
 	if (cpu_has_feature(CPU_FTR_DSCR)) {
-		if (current->thread.dscr_inherit) {
-			p->thread.dscr_inherit = 1;
-			p->thread.dscr = current->thread.dscr;
-		} else if (0 != dscr_default) {
-			p->thread.dscr_inherit = 1;
-			p->thread.dscr = dscr_default;
-		} else {
-			p->thread.dscr_inherit = 0;
-			p->thread.dscr = 0;
-		}
+		p->thread.dscr_inherit = current->thread.dscr_inherit;
+		p->thread.dscr = current->thread.dscr;
 	}
 #endif
 
diff --git a/arch/powerpc/kernel/smp.c b/arch/powerpc/kernel/smp.c
index 0321007..8d4214a 100644
--- a/arch/powerpc/kernel/smp.c
+++ b/arch/powerpc/kernel/smp.c
@@ -198,8 +198,15 @@
 	struct cpu_messages *info = &per_cpu(ipi_message, cpu);
 	char *message = (char *)&info->messages;
 
+	/*
+	 * Order previous accesses before accesses in the IPI handler.
+	 */
+	smp_mb();
 	message[msg] = 1;
-	mb();
+	/*
+	 * cause_ipi functions are required to include a full barrier
+	 * before doing whatever causes the IPI.
+	 */
 	smp_ops->cause_ipi(cpu, info->data);
 }
 
@@ -211,7 +218,7 @@
 	mb();	/* order any irq clear */
 
 	do {
-		all = xchg_local(&info->messages, 0);
+		all = xchg(&info->messages, 0);
 
 #ifdef __BIG_ENDIAN
 		if (all & (1 << (24 - 8 * PPC_MSG_CALL_FUNCTION)))
diff --git a/arch/powerpc/kernel/sysfs.c b/arch/powerpc/kernel/sysfs.c
index 3529446..8302af6 100644
--- a/arch/powerpc/kernel/sysfs.c
+++ b/arch/powerpc/kernel/sysfs.c
@@ -194,6 +194,14 @@
 	return sprintf(buf, "%lx\n", dscr_default);
 }
 
+static void update_dscr(void *dummy)
+{
+	if (!current->thread.dscr_inherit) {
+		current->thread.dscr = dscr_default;
+		mtspr(SPRN_DSCR, dscr_default);
+	}
+}
+
 static ssize_t __used store_dscr_default(struct device *dev,
 		struct device_attribute *attr, const char *buf,
 		size_t count)
@@ -206,6 +214,8 @@
 		return -EINVAL;
 	dscr_default = val;
 
+	on_each_cpu(update_dscr, NULL, 1);
+
 	return count;
 }
 
diff --git a/arch/powerpc/kernel/time.c b/arch/powerpc/kernel/time.c
index be171ee..e49e931 100644
--- a/arch/powerpc/kernel/time.c
+++ b/arch/powerpc/kernel/time.c
@@ -535,6 +535,15 @@
 	trace_timer_interrupt_exit(regs);
 }
 
+/*
+ * Hypervisor decrementer interrupts shouldn't occur but are sometimes
+ * left pending on exit from a KVM guest.  We don't need to do anything
+ * to clear them, as they are edge-triggered.
+ */
+void hdec_interrupt(struct pt_regs *regs)
+{
+}
+
 #ifdef CONFIG_SUSPEND
 static void generic_suspend_disable_irqs(void)
 {
diff --git a/arch/powerpc/kernel/traps.c b/arch/powerpc/kernel/traps.c
index 1589723..ae0843f 100644
--- a/arch/powerpc/kernel/traps.c
+++ b/arch/powerpc/kernel/traps.c
@@ -972,8 +972,9 @@
 			cpu_has_feature(CPU_FTR_DSCR)) {
 		PPC_WARN_EMULATED(mtdscr, regs);
 		rd = (instword >> 21) & 0x1f;
-		mtspr(SPRN_DSCR, regs->gpr[rd]);
+		current->thread.dscr = regs->gpr[rd];
 		current->thread.dscr_inherit = 1;
+		mtspr(SPRN_DSCR, current->thread.dscr);
 		return 0;
 	}
 #endif
diff --git a/arch/powerpc/lib/code-patching.c b/arch/powerpc/lib/code-patching.c
index dd223b3..17e5b23 100644
--- a/arch/powerpc/lib/code-patching.c
+++ b/arch/powerpc/lib/code-patching.c
@@ -20,7 +20,7 @@
 {
 	int err;
 
-	err = __put_user(instr, addr);
+	__put_user_size(instr, addr, 4, err);
 	if (err)
 		return err;
 	asm ("dcbst 0, %0; sync; icbi 0,%0; sync; isync" : : "r" (addr));
diff --git a/arch/powerpc/mm/numa.c b/arch/powerpc/mm/numa.c
index 39b1597..59213cf 100644
--- a/arch/powerpc/mm/numa.c
+++ b/arch/powerpc/mm/numa.c
@@ -1436,11 +1436,11 @@
 
 /*
  * Update the node maps and sysfs entries for each cpu whose home node
- * has changed.
+ * has changed. Returns 1 when the topology has changed, and 0 otherwise.
  */
 int arch_update_cpu_topology(void)
 {
-	int cpu, nid, old_nid;
+	int cpu, nid, old_nid, changed = 0;
 	unsigned int associativity[VPHN_ASSOC_BUFSIZE] = {0};
 	struct device *dev;
 
@@ -1466,9 +1466,10 @@
 		dev = get_cpu_device(cpu);
 		if (dev)
 			kobject_uevent(&dev->kobj, KOBJ_CHANGE);
+		changed = 1;
 	}
 
-	return 1;
+	return changed;
 }
 
 static void topology_work_fn(struct work_struct *work)
diff --git a/arch/powerpc/platforms/powernv/smp.c b/arch/powerpc/platforms/powernv/smp.c
index 3ef4625..7698b6e 100644
--- a/arch/powerpc/platforms/powernv/smp.c
+++ b/arch/powerpc/platforms/powernv/smp.c
@@ -106,14 +106,6 @@
 {
 	unsigned int cpu;
 
-	/* If powersave_nap is enabled, use NAP mode, else just
-	 * spin aimlessly
-	 */
-	if (!powersave_nap) {
-		generic_mach_cpu_die();
-		return;
-	}
-
 	/* Standard hot unplug procedure */
 	local_irq_disable();
 	idle_task_exit();
@@ -128,7 +120,7 @@
 	 */
 	mtspr(SPRN_LPCR, mfspr(SPRN_LPCR) & ~(u64)LPCR_PECE1);
 	while (!generic_check_cpu_restart(cpu)) {
-		power7_idle();
+		power7_nap();
 		if (!generic_check_cpu_restart(cpu)) {
 			DBG("CPU%d Unexpected exit while offline !\n", cpu);
 			/* We may be getting an IPI, so we re-enable
diff --git a/arch/powerpc/sysdev/xics/icp-hv.c b/arch/powerpc/sysdev/xics/icp-hv.c
index 14469cf..df0fc58 100644
--- a/arch/powerpc/sysdev/xics/icp-hv.c
+++ b/arch/powerpc/sysdev/xics/icp-hv.c
@@ -65,7 +65,11 @@
 static inline void icp_hv_set_qirr(int n_cpu , u8 value)
 {
 	int hw_cpu = get_hard_smp_processor_id(n_cpu);
-	long rc = plpar_hcall_norets(H_IPI, hw_cpu, value);
+	long rc;
+
+	/* Make sure all previous accesses are ordered before IPI sending */
+	mb();
+	rc = plpar_hcall_norets(H_IPI, hw_cpu, value);
 	if (rc != H_SUCCESS) {
 		pr_err("%s: bad return code qirr cpu=%d hw_cpu=%d mfrr=0x%x "
 			"returned %ld\n", __func__, n_cpu, hw_cpu, value, rc);
diff --git a/arch/s390/oprofile/init.c b/arch/s390/oprofile/init.c
index a1e9d69..584b936 100644
--- a/arch/s390/oprofile/init.c
+++ b/arch/s390/oprofile/init.c
@@ -169,7 +169,7 @@
 	if (*offset)
 		return -EINVAL;
 	retval = oprofilefs_ulong_from_user(&val, buf, count);
-	if (retval)
+	if (retval <= 0)
 		return retval;
 	if (val < oprofile_min_interval)
 		oprofile_hw_interval = oprofile_min_interval;
@@ -212,7 +212,7 @@
 		return -EINVAL;
 
 	retval = oprofilefs_ulong_from_user(&val, buf, count);
-	if (retval)
+	if (retval <= 0)
 		return retval;
 	if (val != 0)
 		return -EINVAL;
@@ -243,7 +243,7 @@
 		return -EINVAL;
 
 	retval = oprofilefs_ulong_from_user(&val, buf, count);
-	if (retval)
+	if (retval <= 0)
 		return retval;
 
 	if (val != 0 && val != 1)
@@ -278,7 +278,7 @@
 		return -EINVAL;
 
 	retval = oprofilefs_ulong_from_user(&val, buf, count);
-	if (retval)
+	if (retval <= 0)
 		return retval;
 
 	if (val != 0 && val != 1)
@@ -317,7 +317,7 @@
 		return -EINVAL;
 
 	retval = oprofilefs_ulong_from_user(&val, buf, count);
-	if (retval)
+	if (retval <= 0)
 		return retval;
 
 	if (val != 0 && val != 1)
diff --git a/arch/um/os-Linux/time.c b/arch/um/os-Linux/time.c
index f602385..0748fe0 100644
--- a/arch/um/os-Linux/time.c
+++ b/arch/um/os-Linux/time.c
@@ -114,7 +114,7 @@
 	skew += this_tick - last_tick;
 
 	while (skew >= one_tick) {
-		alarm_handler(SIGVTALRM, NULL);
+		alarm_handler(SIGVTALRM, NULL, NULL);
 		skew -= one_tick;
 	}
 
diff --git a/arch/x86/kernel/cpu/perf_event_intel.c b/arch/x86/kernel/cpu/perf_event_intel.c
index 7f2739e..0d3d63a 100644
--- a/arch/x86/kernel/cpu/perf_event_intel.c
+++ b/arch/x86/kernel/cpu/perf_event_intel.c
@@ -2008,6 +2008,7 @@
 		break;
 
 	case 28: /* Atom */
+	case 54: /* Cedariew */
 		memcpy(hw_cache_event_ids, atom_hw_cache_event_ids,
 		       sizeof(hw_cache_event_ids));
 
diff --git a/arch/x86/kernel/cpu/perf_event_intel_lbr.c b/arch/x86/kernel/cpu/perf_event_intel_lbr.c
index 520b426..da02e9c 100644
--- a/arch/x86/kernel/cpu/perf_event_intel_lbr.c
+++ b/arch/x86/kernel/cpu/perf_event_intel_lbr.c
@@ -686,7 +686,8 @@
 	 * to have an operational LBR which can freeze
 	 * on PMU interrupt
 	 */
-	if (boot_cpu_data.x86_mask < 10) {
+	if (boot_cpu_data.x86_model == 28
+	    && boot_cpu_data.x86_mask < 10) {
 		pr_cont("LBR disabled due to erratum");
 		return;
 	}
diff --git a/arch/x86/kernel/microcode_core.c b/arch/x86/kernel/microcode_core.c
index 4873e62..9e5bcf1 100644
--- a/arch/x86/kernel/microcode_core.c
+++ b/arch/x86/kernel/microcode_core.c
@@ -225,6 +225,9 @@
 	if (do_microcode_update(buf, len) == 0)
 		ret = (ssize_t)len;
 
+	if (ret > 0)
+		perf_check_microcode();
+
 	mutex_unlock(&microcode_mutex);
 	put_online_cpus();
 
diff --git a/arch/x86/kvm/i8259.c b/arch/x86/kvm/i8259.c
index e498b18..9fc9aa7 100644
--- a/arch/x86/kvm/i8259.c
+++ b/arch/x86/kvm/i8259.c
@@ -318,7 +318,7 @@
 		if (val & 0x10) {
 			u8 edge_irr = s->irr & ~s->elcr;
 			int i;
-			bool found;
+			bool found = false;
 			struct kvm_vcpu *vcpu;
 
 			s->init4 = val & 1;
diff --git a/arch/x86/kvm/vmx.c b/arch/x86/kvm/vmx.c
index c00f03d..b1eb202 100644
--- a/arch/x86/kvm/vmx.c
+++ b/arch/x86/kvm/vmx.c
@@ -3619,6 +3619,7 @@
 
 static int alloc_apic_access_page(struct kvm *kvm)
 {
+	struct page *page;
 	struct kvm_userspace_memory_region kvm_userspace_mem;
 	int r = 0;
 
@@ -3633,7 +3634,13 @@
 	if (r)
 		goto out;
 
-	kvm->arch.apic_access_page = gfn_to_page(kvm, 0xfee00);
+	page = gfn_to_page(kvm, 0xfee00);
+	if (is_error_page(page)) {
+		r = -EFAULT;
+		goto out;
+	}
+
+	kvm->arch.apic_access_page = page;
 out:
 	mutex_unlock(&kvm->slots_lock);
 	return r;
@@ -3641,6 +3648,7 @@
 
 static int alloc_identity_pagetable(struct kvm *kvm)
 {
+	struct page *page;
 	struct kvm_userspace_memory_region kvm_userspace_mem;
 	int r = 0;
 
@@ -3656,8 +3664,13 @@
 	if (r)
 		goto out;
 
-	kvm->arch.ept_identity_pagetable = gfn_to_page(kvm,
-			kvm->arch.ept_identity_map_addr >> PAGE_SHIFT);
+	page = gfn_to_page(kvm, kvm->arch.ept_identity_map_addr >> PAGE_SHIFT);
+	if (is_error_page(page)) {
+		r = -EFAULT;
+		goto out;
+	}
+
+	kvm->arch.ept_identity_pagetable = page;
 out:
 	mutex_unlock(&kvm->slots_lock);
 	return r;
@@ -6575,7 +6588,7 @@
 	/* Exposing INVPCID only when PCID is exposed */
 	best = kvm_find_cpuid_entry(vcpu, 0x7, 0);
 	if (vmx_invpcid_supported() &&
-	    best && (best->ecx & bit(X86_FEATURE_INVPCID)) &&
+	    best && (best->ebx & bit(X86_FEATURE_INVPCID)) &&
 	    guest_cpuid_has_pcid(vcpu)) {
 		exec_control |= SECONDARY_EXEC_ENABLE_INVPCID;
 		vmcs_write32(SECONDARY_VM_EXEC_CONTROL,
@@ -6585,7 +6598,7 @@
 		vmcs_write32(SECONDARY_VM_EXEC_CONTROL,
 			     exec_control);
 		if (best)
-			best->ecx &= ~bit(X86_FEATURE_INVPCID);
+			best->ebx &= ~bit(X86_FEATURE_INVPCID);
 	}
 }
 
diff --git a/arch/x86/kvm/x86.c b/arch/x86/kvm/x86.c
index 148ed66..2966c84 100644
--- a/arch/x86/kvm/x86.c
+++ b/arch/x86/kvm/x86.c
@@ -5113,17 +5113,20 @@
 			!kvm_event_needs_reinjection(vcpu);
 }
 
-static void vapic_enter(struct kvm_vcpu *vcpu)
+static int vapic_enter(struct kvm_vcpu *vcpu)
 {
 	struct kvm_lapic *apic = vcpu->arch.apic;
 	struct page *page;
 
 	if (!apic || !apic->vapic_addr)
-		return;
+		return 0;
 
 	page = gfn_to_page(vcpu->kvm, apic->vapic_addr >> PAGE_SHIFT);
+	if (is_error_page(page))
+		return -EFAULT;
 
 	vcpu->arch.apic->vapic_page = page;
+	return 0;
 }
 
 static void vapic_exit(struct kvm_vcpu *vcpu)
@@ -5430,7 +5433,11 @@
 	}
 
 	vcpu->srcu_idx = srcu_read_lock(&kvm->srcu);
-	vapic_enter(vcpu);
+	r = vapic_enter(vcpu);
+	if (r) {
+		srcu_read_unlock(&kvm->srcu, vcpu->srcu_idx);
+		return r;
+	}
 
 	r = 1;
 	while (r > 0) {
diff --git a/arch/x86/xen/mmu.c b/arch/x86/xen/mmu.c
index b65a761..5141d80 100644
--- a/arch/x86/xen/mmu.c
+++ b/arch/x86/xen/mmu.c
@@ -1283,7 +1283,7 @@
 	cpumask_clear_cpu(smp_processor_id(), to_cpumask(args->mask));
 
 	args->op.cmd = MMUEXT_TLB_FLUSH_MULTI;
-	if (start != TLB_FLUSH_ALL && (end - start) <= PAGE_SIZE) {
+	if (end != TLB_FLUSH_ALL && (end - start) <= PAGE_SIZE) {
 		args->op.cmd = MMUEXT_INVLPG_MULTI;
 		args->op.arg1.linear_addr = start;
 	}
diff --git a/arch/x86/xen/p2m.c b/arch/x86/xen/p2m.c
index d4b2554..76ba0e9 100644
--- a/arch/x86/xen/p2m.c
+++ b/arch/x86/xen/p2m.c
@@ -599,7 +599,7 @@
 	if (p2m_index(set_pfn))
 		return false;
 
-	for (pfn = 0; pfn <= MAX_DOMAIN_PAGES; pfn += P2M_PER_PAGE) {
+	for (pfn = 0; pfn < MAX_DOMAIN_PAGES; pfn += P2M_PER_PAGE) {
 		topidx = p2m_top_index(pfn);
 
 		if (!p2m_top[topidx])
diff --git a/crypto/authenc.c b/crypto/authenc.c
index 5ef7ba6..d0583a4 100644
--- a/crypto/authenc.c
+++ b/crypto/authenc.c
@@ -336,7 +336,7 @@
 		cryptlen += ivsize;
 	}
 
-	if (sg_is_last(assoc)) {
+	if (req->assoclen && sg_is_last(assoc)) {
 		authenc_ahash_fn = crypto_authenc_ahash;
 		sg_init_table(asg, 2);
 		sg_set_page(asg, sg_page(assoc), assoc->length, assoc->offset);
@@ -490,7 +490,7 @@
 		cryptlen += ivsize;
 	}
 
-	if (sg_is_last(assoc)) {
+	if (req->assoclen && sg_is_last(assoc)) {
 		authenc_ahash_fn = crypto_authenc_ahash;
 		sg_init_table(asg, 2);
 		sg_set_page(asg, sg_page(assoc), assoc->length, assoc->offset);
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index 50d5dea..7862d17 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -268,6 +268,9 @@
 	/* JMicron 360/1/3/5/6, match class to avoid IDE function */
 	{ PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
 	  PCI_CLASS_STORAGE_SATA_AHCI, 0xffffff, board_ahci_ign_iferr },
+	/* JMicron 362B and 362C have an AHCI function with IDE class code */
+	{ PCI_VDEVICE(JMICRON, 0x2362), board_ahci_ign_iferr },
+	{ PCI_VDEVICE(JMICRON, 0x236f), board_ahci_ign_iferr },
 
 	/* ATI */
 	{ PCI_VDEVICE(ATI, 0x4380), board_ahci_sb600 }, /* ATI SB600 */
@@ -393,6 +396,8 @@
 	  .driver_data = board_ahci_yes_fbs },			/* 88se9125 */
 	{ PCI_DEVICE(0x1b4b, 0x917a),
 	  .driver_data = board_ahci_yes_fbs },			/* 88se9172 */
+	{ PCI_DEVICE(0x1b4b, 0x9192),
+	  .driver_data = board_ahci_yes_fbs },			/* 88se9172 on some Gigabyte */
 	{ PCI_DEVICE(0x1b4b, 0x91a3),
 	  .driver_data = board_ahci_yes_fbs },
 
@@ -400,7 +405,10 @@
 	{ PCI_VDEVICE(PROMISE, 0x3f20), board_ahci },	/* PDC42819 */
 
 	/* Asmedia */
-	{ PCI_VDEVICE(ASMEDIA, 0x0612), board_ahci },	/* ASM1061 */
+	{ PCI_VDEVICE(ASMEDIA, 0x0601), board_ahci },	/* ASM1060 */
+	{ PCI_VDEVICE(ASMEDIA, 0x0602), board_ahci },	/* ASM1060 */
+	{ PCI_VDEVICE(ASMEDIA, 0x0611), board_ahci },	/* ASM1061 */
+	{ PCI_VDEVICE(ASMEDIA, 0x0612), board_ahci },	/* ASM1062 */
 
 	/* Generic, PCI class code for AHCI */
 	{ PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
diff --git a/drivers/base/dma-contiguous.c b/drivers/base/dma-contiguous.c
index 78efb03..34d94c7 100644
--- a/drivers/base/dma-contiguous.c
+++ b/drivers/base/dma-contiguous.c
@@ -250,7 +250,7 @@
 		return -EINVAL;
 
 	/* Sanitise input arguments */
-	alignment = PAGE_SIZE << max(MAX_ORDER, pageblock_order);
+	alignment = PAGE_SIZE << max(MAX_ORDER - 1, pageblock_order);
 	base = ALIGN(base, alignment);
 	size = ALIGN(size, alignment);
 	limit &= ~(alignment - 1);
diff --git a/drivers/crypto/caam/key_gen.c b/drivers/crypto/caam/key_gen.c
index 0028881..d216cd3 100644
--- a/drivers/crypto/caam/key_gen.c
+++ b/drivers/crypto/caam/key_gen.c
@@ -120,3 +120,4 @@
 
 	return ret;
 }
+EXPORT_SYMBOL(gen_split_key);
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index b16c8a7..ba7926f5 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -294,7 +294,7 @@
 
 config GPIO_MC9S08DZ60
 	bool "MX35 3DS BOARD MC9S08DZ60 GPIO functions"
-	depends on I2C && MACH_MX35_3DS
+	depends on I2C=y && MACH_MX35_3DS
 	help
 	  Select this to enable the MC9S08DZ60 GPIO driver
 
diff --git a/drivers/gpio/gpio-em.c b/drivers/gpio/gpio-em.c
index ae37181..ec48ed5 100644
--- a/drivers/gpio/gpio-em.c
+++ b/drivers/gpio/gpio-em.c
@@ -247,9 +247,9 @@
 
 	p->irq_base = irq_alloc_descs(pdata->irq_base, 0,
 				      pdata->number_of_pins, numa_node_id());
-	if (IS_ERR_VALUE(p->irq_base)) {
+	if (p->irq_base < 0) {
 		dev_err(&pdev->dev, "cannot get irq_desc\n");
-		return -ENXIO;
+		return p->irq_base;
 	}
 	pr_debug("gio: hw base = %d, nr = %d, sw base = %d\n",
 		 pdata->gpio_base, pdata->number_of_pins, p->irq_base);
diff --git a/drivers/gpio/gpio-rdc321x.c b/drivers/gpio/gpio-rdc321x.c
index e97016a..b62d443 100644
--- a/drivers/gpio/gpio-rdc321x.c
+++ b/drivers/gpio/gpio-rdc321x.c
@@ -170,6 +170,7 @@
 	rdc321x_gpio_dev->reg2_data_base = r->start + 0x4;
 
 	rdc321x_gpio_dev->chip.label = "rdc321x-gpio";
+	rdc321x_gpio_dev->chip.owner = THIS_MODULE;
 	rdc321x_gpio_dev->chip.direction_input = rdc_gpio_direction_input;
 	rdc321x_gpio_dev->chip.direction_output = rdc_gpio_config;
 	rdc321x_gpio_dev->chip.get = rdc_gpio_get_value;
diff --git a/drivers/gpio/gpiolib-of.c b/drivers/gpio/gpiolib-of.c
index a18c4aa..f1a4599 100644
--- a/drivers/gpio/gpiolib-of.c
+++ b/drivers/gpio/gpiolib-of.c
@@ -82,7 +82,7 @@
 	gpiochip_find(&gg_data, of_gpiochip_find_and_xlate);
 
 	of_node_put(gg_data.gpiospec.np);
-	pr_debug("%s exited with status %d\n", __func__, ret);
+	pr_debug("%s exited with status %d\n", __func__, gg_data.out_gpio);
 	return gg_data.out_gpio;
 }
 EXPORT_SYMBOL(of_get_named_gpio_flags);
diff --git a/drivers/gpu/drm/ast/ast_drv.c b/drivers/gpu/drm/ast/ast_drv.c
index d0c4574..3616480 100644
--- a/drivers/gpu/drm/ast/ast_drv.c
+++ b/drivers/gpu/drm/ast/ast_drv.c
@@ -193,6 +193,9 @@
 	.mmap = ast_mmap,
 	.poll = drm_poll,
 	.fasync = drm_fasync,
+#ifdef CONFIG_COMPAT
+	.compat_ioctl = drm_compat_ioctl,
+#endif
 	.read = drm_read,
 };
 
diff --git a/drivers/gpu/drm/ast/ast_mode.c b/drivers/gpu/drm/ast/ast_mode.c
index 7282c08..a712caf 100644
--- a/drivers/gpu/drm/ast/ast_mode.c
+++ b/drivers/gpu/drm/ast/ast_mode.c
@@ -841,7 +841,7 @@
 
 	ast->cursor_cache = obj;
 	ast->cursor_cache_gpu_addr = gpu_addr;
-	DRM_ERROR("pinned cursor cache at %llx\n", ast->cursor_cache_gpu_addr);
+	DRM_DEBUG_KMS("pinned cursor cache at %llx\n", ast->cursor_cache_gpu_addr);
 	return 0;
 fail:
 	return ret;
diff --git a/drivers/gpu/drm/cirrus/cirrus_drv.c b/drivers/gpu/drm/cirrus/cirrus_drv.c
index 7053140..b83a2d7 100644
--- a/drivers/gpu/drm/cirrus/cirrus_drv.c
+++ b/drivers/gpu/drm/cirrus/cirrus_drv.c
@@ -74,6 +74,9 @@
 	.unlocked_ioctl = drm_ioctl,
 	.mmap = cirrus_mmap,
 	.poll = drm_poll,
+#ifdef CONFIG_COMPAT
+	.compat_ioctl = drm_compat_ioctl,
+#endif
 	.fasync = drm_fasync,
 };
 static struct drm_driver driver = {
diff --git a/drivers/gpu/drm/exynos/Kconfig b/drivers/gpu/drm/exynos/Kconfig
index 7f50967..59a26e5 100644
--- a/drivers/gpu/drm/exynos/Kconfig
+++ b/drivers/gpu/drm/exynos/Kconfig
@@ -36,6 +36,6 @@
 
 config DRM_EXYNOS_G2D
 	bool "Exynos DRM G2D"
-	depends on DRM_EXYNOS
+	depends on DRM_EXYNOS && !VIDEO_SAMSUNG_S5P_G2D
 	help
 	  Choose this option if you want to use Exynos G2D for DRM.
diff --git a/drivers/gpu/drm/exynos/exynos_drm_dmabuf.c b/drivers/gpu/drm/exynos/exynos_drm_dmabuf.c
index 613bf8a..ae13feb 100644
--- a/drivers/gpu/drm/exynos/exynos_drm_dmabuf.c
+++ b/drivers/gpu/drm/exynos/exynos_drm_dmabuf.c
@@ -163,6 +163,12 @@
 	/* TODO */
 }
 
+static int exynos_gem_dmabuf_mmap(struct dma_buf *dma_buf,
+	struct vm_area_struct *vma)
+{
+	return -ENOTTY;
+}
+
 static struct dma_buf_ops exynos_dmabuf_ops = {
 	.map_dma_buf		= exynos_gem_map_dma_buf,
 	.unmap_dma_buf		= exynos_gem_unmap_dma_buf,
@@ -170,6 +176,7 @@
 	.kmap_atomic		= exynos_gem_dmabuf_kmap_atomic,
 	.kunmap			= exynos_gem_dmabuf_kunmap,
 	.kunmap_atomic		= exynos_gem_dmabuf_kunmap_atomic,
+	.mmap			= exynos_gem_dmabuf_mmap,
 	.release		= exynos_dmabuf_release,
 };
 
diff --git a/drivers/gpu/drm/exynos/exynos_drm_drv.c b/drivers/gpu/drm/exynos/exynos_drm_drv.c
index ebacec6..d070719 100644
--- a/drivers/gpu/drm/exynos/exynos_drm_drv.c
+++ b/drivers/gpu/drm/exynos/exynos_drm_drv.c
@@ -160,7 +160,6 @@
 	if (!file_priv)
 		return -ENOMEM;
 
-	drm_prime_init_file_private(&file->prime);
 	file->driver_priv = file_priv;
 
 	return exynos_drm_subdrv_open(dev, file);
@@ -184,7 +183,6 @@
 			e->base.destroy(&e->base);
 		}
 	}
-	drm_prime_destroy_file_private(&file->prime);
 	spin_unlock_irqrestore(&dev->event_lock, flags);
 
 	exynos_drm_subdrv_close(dev, file);
@@ -241,6 +239,9 @@
 	.poll		= drm_poll,
 	.read		= drm_read,
 	.unlocked_ioctl	= drm_ioctl,
+#ifdef CONFIG_COMPAT
+	.compat_ioctl = drm_compat_ioctl,
+#endif
 	.release	= drm_release,
 };
 
diff --git a/drivers/gpu/drm/exynos/exynos_drm_fimd.c b/drivers/gpu/drm/exynos/exynos_drm_fimd.c
index a68d2b3..b19cd93 100644
--- a/drivers/gpu/drm/exynos/exynos_drm_fimd.c
+++ b/drivers/gpu/drm/exynos/exynos_drm_fimd.c
@@ -831,11 +831,6 @@
 	}
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!res) {
-		dev_err(dev, "failed to find registers\n");
-		ret = -ENOENT;
-		goto err_clk;
-	}
 
 	ctx->regs = devm_request_and_ioremap(&pdev->dev, res);
 	if (!ctx->regs) {
diff --git a/drivers/gpu/drm/exynos/exynos_drm_g2d.c b/drivers/gpu/drm/exynos/exynos_drm_g2d.c
index d2d88f2..1065e90 100644
--- a/drivers/gpu/drm/exynos/exynos_drm_g2d.c
+++ b/drivers/gpu/drm/exynos/exynos_drm_g2d.c
@@ -129,7 +129,6 @@
 struct g2d_data {
 	struct device			*dev;
 	struct clk			*gate_clk;
-	struct resource			*regs_res;
 	void __iomem			*regs;
 	int				irq;
 	struct workqueue_struct		*g2d_workq;
@@ -751,7 +750,7 @@
 	struct exynos_drm_subdrv *subdrv;
 	int ret;
 
-	g2d = kzalloc(sizeof(*g2d), GFP_KERNEL);
+	g2d = devm_kzalloc(&pdev->dev, sizeof(*g2d), GFP_KERNEL);
 	if (!g2d) {
 		dev_err(dev, "failed to allocate driver data\n");
 		return -ENOMEM;
@@ -759,10 +758,8 @@
 
 	g2d->runqueue_slab = kmem_cache_create("g2d_runqueue_slab",
 			sizeof(struct g2d_runqueue_node), 0, 0, NULL);
-	if (!g2d->runqueue_slab) {
-		ret = -ENOMEM;
-		goto err_free_mem;
-	}
+	if (!g2d->runqueue_slab)
+		return -ENOMEM;
 
 	g2d->dev = dev;
 
@@ -794,38 +791,26 @@
 	pm_runtime_enable(dev);
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!res) {
-		dev_err(dev, "failed to get I/O memory\n");
-		ret = -ENOENT;
-		goto err_put_clk;
-	}
 
-	g2d->regs_res = request_mem_region(res->start, resource_size(res),
-					   dev_name(dev));
-	if (!g2d->regs_res) {
-		dev_err(dev, "failed to request I/O memory\n");
-		ret = -ENOENT;
-		goto err_put_clk;
-	}
-
-	g2d->regs = ioremap(res->start, resource_size(res));
+	g2d->regs = devm_request_and_ioremap(&pdev->dev, res);
 	if (!g2d->regs) {
 		dev_err(dev, "failed to remap I/O memory\n");
 		ret = -ENXIO;
-		goto err_release_res;
+		goto err_put_clk;
 	}
 
 	g2d->irq = platform_get_irq(pdev, 0);
 	if (g2d->irq < 0) {
 		dev_err(dev, "failed to get irq\n");
 		ret = g2d->irq;
-		goto err_unmap_base;
+		goto err_put_clk;
 	}
 
-	ret = request_irq(g2d->irq, g2d_irq_handler, 0, "drm_g2d", g2d);
+	ret = devm_request_irq(&pdev->dev, g2d->irq, g2d_irq_handler, 0,
+								"drm_g2d", g2d);
 	if (ret < 0) {
 		dev_err(dev, "irq request failed\n");
-		goto err_unmap_base;
+		goto err_put_clk;
 	}
 
 	platform_set_drvdata(pdev, g2d);
@@ -838,7 +823,7 @@
 	ret = exynos_drm_subdrv_register(subdrv);
 	if (ret < 0) {
 		dev_err(dev, "failed to register drm g2d device\n");
-		goto err_free_irq;
+		goto err_put_clk;
 	}
 
 	dev_info(dev, "The exynos g2d(ver %d.%d) successfully probed\n",
@@ -846,13 +831,6 @@
 
 	return 0;
 
-err_free_irq:
-	free_irq(g2d->irq, g2d);
-err_unmap_base:
-	iounmap(g2d->regs);
-err_release_res:
-	release_resource(g2d->regs_res);
-	kfree(g2d->regs_res);
 err_put_clk:
 	pm_runtime_disable(dev);
 	clk_put(g2d->gate_clk);
@@ -862,8 +840,6 @@
 	destroy_workqueue(g2d->g2d_workq);
 err_destroy_slab:
 	kmem_cache_destroy(g2d->runqueue_slab);
-err_free_mem:
-	kfree(g2d);
 	return ret;
 }
 
@@ -873,24 +849,18 @@
 
 	cancel_work_sync(&g2d->runqueue_work);
 	exynos_drm_subdrv_unregister(&g2d->subdrv);
-	free_irq(g2d->irq, g2d);
 
 	while (g2d->runqueue_node) {
 		g2d_free_runqueue_node(g2d, g2d->runqueue_node);
 		g2d->runqueue_node = g2d_get_runqueue_node(g2d);
 	}
 
-	iounmap(g2d->regs);
-	release_resource(g2d->regs_res);
-	kfree(g2d->regs_res);
-
 	pm_runtime_disable(&pdev->dev);
 	clk_put(g2d->gate_clk);
 
 	g2d_fini_cmdlist(g2d);
 	destroy_workqueue(g2d->g2d_workq);
 	kmem_cache_destroy(g2d->runqueue_slab);
-	kfree(g2d);
 
 	return 0;
 }
@@ -924,7 +894,7 @@
 }
 #endif
 
-SIMPLE_DEV_PM_OPS(g2d_pm_ops, g2d_suspend, g2d_resume);
+static SIMPLE_DEV_PM_OPS(g2d_pm_ops, g2d_suspend, g2d_resume);
 
 struct platform_driver g2d_driver = {
 	.probe		= g2d_probe,
diff --git a/drivers/gpu/drm/exynos/exynos_drm_gem.c b/drivers/gpu/drm/exynos/exynos_drm_gem.c
index f9efde4..a38051c 100644
--- a/drivers/gpu/drm/exynos/exynos_drm_gem.c
+++ b/drivers/gpu/drm/exynos/exynos_drm_gem.c
@@ -122,7 +122,7 @@
 		__free_page(pages[i]);
 
 	drm_free_large(pages);
-	return ERR_PTR(PTR_ERR(p));
+	return ERR_CAST(p);
 }
 
 static void exynos_gem_put_pages(struct drm_gem_object *obj,
@@ -662,7 +662,7 @@
 	 */
 
 	args->pitch = args->width * ((args->bpp + 7) / 8);
-	args->size = PAGE_ALIGN(args->pitch * args->height);
+	args->size = args->pitch * args->height;
 
 	exynos_gem_obj = exynos_drm_gem_create(dev, args->flags, args->size);
 	if (IS_ERR(exynos_gem_obj))
diff --git a/drivers/gpu/drm/exynos/exynos_drm_hdmi.c b/drivers/gpu/drm/exynos/exynos_drm_hdmi.c
index 8ffcdf8..3fdf0b6 100644
--- a/drivers/gpu/drm/exynos/exynos_drm_hdmi.c
+++ b/drivers/gpu/drm/exynos/exynos_drm_hdmi.c
@@ -345,7 +345,7 @@
 
 	DRM_DEBUG_KMS("%s\n", __FILE__);
 
-	ctx = kzalloc(sizeof(*ctx), GFP_KERNEL);
+	ctx = devm_kzalloc(&pdev->dev, sizeof(*ctx), GFP_KERNEL);
 	if (!ctx) {
 		DRM_LOG_KMS("failed to alloc common hdmi context.\n");
 		return -ENOMEM;
@@ -371,7 +371,6 @@
 	DRM_DEBUG_KMS("%s\n", __FILE__);
 
 	exynos_drm_subdrv_unregister(&ctx->subdrv);
-	kfree(ctx);
 
 	return 0;
 }
diff --git a/drivers/gpu/drm/exynos/exynos_drm_plane.c b/drivers/gpu/drm/exynos/exynos_drm_plane.c
index b89829e..e1f94b7 100644
--- a/drivers/gpu/drm/exynos/exynos_drm_plane.c
+++ b/drivers/gpu/drm/exynos/exynos_drm_plane.c
@@ -29,7 +29,6 @@
 	DRM_FORMAT_XRGB8888,
 	DRM_FORMAT_ARGB8888,
 	DRM_FORMAT_NV12,
-	DRM_FORMAT_NV12M,
 	DRM_FORMAT_NV12MT,
 };
 
diff --git a/drivers/gpu/drm/exynos/exynos_drm_vidi.c b/drivers/gpu/drm/exynos/exynos_drm_vidi.c
index bb1550c..537027a 100644
--- a/drivers/gpu/drm/exynos/exynos_drm_vidi.c
+++ b/drivers/gpu/drm/exynos/exynos_drm_vidi.c
@@ -633,7 +633,7 @@
 
 	DRM_DEBUG_KMS("%s\n", __FILE__);
 
-	ctx = kzalloc(sizeof(*ctx), GFP_KERNEL);
+	ctx = devm_kzalloc(&pdev->dev, sizeof(*ctx), GFP_KERNEL);
 	if (!ctx)
 		return -ENOMEM;
 
@@ -673,8 +673,6 @@
 		ctx->raw_edid = NULL;
 	}
 
-	kfree(ctx);
-
 	return 0;
 }
 
diff --git a/drivers/gpu/drm/exynos/exynos_hdmi.c b/drivers/gpu/drm/exynos/exynos_hdmi.c
index 409e2ec..a6aea6f 100644
--- a/drivers/gpu/drm/exynos/exynos_hdmi.c
+++ b/drivers/gpu/drm/exynos/exynos_hdmi.c
@@ -2172,7 +2172,7 @@
 
 	DRM_DEBUG_KMS("HDMI resource init\n");
 
-	memset(res, 0, sizeof *res);
+	memset(res, 0, sizeof(*res));
 
 	/* get clocks, power */
 	res->hdmi = clk_get(dev, "hdmi");
@@ -2204,7 +2204,7 @@
 	clk_set_parent(res->sclk_hdmi, res->sclk_pixel);
 
 	res->regul_bulk = kzalloc(ARRAY_SIZE(supply) *
-		sizeof res->regul_bulk[0], GFP_KERNEL);
+		sizeof(res->regul_bulk[0]), GFP_KERNEL);
 	if (!res->regul_bulk) {
 		DRM_ERROR("failed to get memory for regulators\n");
 		goto fail;
@@ -2243,7 +2243,7 @@
 		clk_put(res->sclk_hdmi);
 	if (!IS_ERR_OR_NULL(res->hdmi))
 		clk_put(res->hdmi);
-	memset(res, 0, sizeof *res);
+	memset(res, 0, sizeof(*res));
 
 	return 0;
 }
@@ -2312,11 +2312,6 @@
 	}
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!res) {
-		DRM_ERROR("failed to find registers\n");
-		ret = -ENOENT;
-		goto err_resource;
-	}
 
 	hdata->regs = devm_request_and_ioremap(&pdev->dev, res);
 	if (!hdata->regs) {
diff --git a/drivers/gpu/drm/exynos/exynos_mixer.c b/drivers/gpu/drm/exynos/exynos_mixer.c
index 30fcc12..25b97d5e 100644
--- a/drivers/gpu/drm/exynos/exynos_mixer.c
+++ b/drivers/gpu/drm/exynos/exynos_mixer.c
@@ -236,11 +236,11 @@
 static void vp_default_filter(struct mixer_resources *res)
 {
 	vp_filter_set(res, VP_POLY8_Y0_LL,
-		filter_y_horiz_tap8, sizeof filter_y_horiz_tap8);
+		filter_y_horiz_tap8, sizeof(filter_y_horiz_tap8));
 	vp_filter_set(res, VP_POLY4_Y0_LL,
-		filter_y_vert_tap4, sizeof filter_y_vert_tap4);
+		filter_y_vert_tap4, sizeof(filter_y_vert_tap4));
 	vp_filter_set(res, VP_POLY4_C0_LL,
-		filter_cr_horiz_tap4, sizeof filter_cr_horiz_tap4);
+		filter_cr_horiz_tap4, sizeof(filter_cr_horiz_tap4));
 }
 
 static void mixer_vsync_set_update(struct mixer_context *ctx, bool enable)
diff --git a/drivers/gpu/drm/gma500/oaktrail_device.c b/drivers/gpu/drm/gma500/oaktrail_device.c
index 0f9b7db..cf49ba5 100644
--- a/drivers/gpu/drm/gma500/oaktrail_device.c
+++ b/drivers/gpu/drm/gma500/oaktrail_device.c
@@ -476,6 +476,7 @@
 		.pos = DSPAPOS,
 		.surf = DSPASURF,
 		.addr = MRST_DSPABASE,
+		.base = MRST_DSPABASE,
 		.status = PIPEASTAT,
 		.linoff = DSPALINOFF,
 		.tileoff = DSPATILEOFF,
@@ -499,6 +500,7 @@
 		.pos = DSPBPOS,
 		.surf = DSPBSURF,
 		.addr = DSPBBASE,
+		.base = DSPBBASE,
 		.status = PIPEBSTAT,
 		.linoff = DSPBLINOFF,
 		.tileoff = DSPBTILEOFF,
diff --git a/drivers/gpu/drm/i810/i810_dma.c b/drivers/gpu/drm/i810/i810_dma.c
index 57d892e..463ec68 100644
--- a/drivers/gpu/drm/i810/i810_dma.c
+++ b/drivers/gpu/drm/i810/i810_dma.c
@@ -115,6 +115,9 @@
 	.unlocked_ioctl = drm_ioctl,
 	.mmap = i810_mmap_buffers,
 	.fasync = drm_fasync,
+#ifdef CONFIG_COMPAT
+	.compat_ioctl = drm_compat_ioctl,
+#endif
 	.llseek = noop_llseek,
 };
 
diff --git a/drivers/gpu/drm/i810/i810_drv.c b/drivers/gpu/drm/i810/i810_drv.c
index f9924ad..48cfcca 100644
--- a/drivers/gpu/drm/i810/i810_drv.c
+++ b/drivers/gpu/drm/i810/i810_drv.c
@@ -51,6 +51,9 @@
 	.mmap = drm_mmap,
 	.poll = drm_poll,
 	.fasync = drm_fasync,
+#ifdef CONFIG_COMPAT
+	.compat_ioctl = drm_compat_ioctl,
+#endif
 	.llseek = noop_llseek,
 };
 
diff --git a/drivers/gpu/drm/i915/i915_dma.c b/drivers/gpu/drm/i915/i915_dma.c
index 9cf7dfe..914c0df 100644
--- a/drivers/gpu/drm/i915/i915_dma.c
+++ b/drivers/gpu/drm/i915/i915_dma.c
@@ -1587,6 +1587,7 @@
 	spin_lock_init(&dev_priv->irq_lock);
 	spin_lock_init(&dev_priv->error_lock);
 	spin_lock_init(&dev_priv->rps_lock);
+	spin_lock_init(&dev_priv->dpio_lock);
 
 	if (IS_IVYBRIDGE(dev) || IS_HASWELL(dev))
 		dev_priv->num_pipe = 3;
diff --git a/drivers/gpu/drm/i915/i915_irq.c b/drivers/gpu/drm/i915/i915_irq.c
index 8a38285..5249640 100644
--- a/drivers/gpu/drm/i915/i915_irq.c
+++ b/drivers/gpu/drm/i915/i915_irq.c
@@ -2700,9 +2700,6 @@
 			dev->driver->irq_handler = i8xx_irq_handler;
 			dev->driver->irq_uninstall = i8xx_irq_uninstall;
 		} else if (INTEL_INFO(dev)->gen == 3) {
-			/* IIR "flip pending" means done if this bit is set */
-			I915_WRITE(ECOSKPD, _MASKED_BIT_DISABLE(ECO_FLIP_DONE));
-
 			dev->driver->irq_preinstall = i915_irq_preinstall;
 			dev->driver->irq_postinstall = i915_irq_postinstall;
 			dev->driver->irq_uninstall = i915_irq_uninstall;
diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index 2dfa6cf..bc2ad34 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -1376,7 +1376,8 @@
 	     "PCH DP (0x%08x) enabled on transcoder %c, should be disabled\n",
 	     reg, pipe_name(pipe));
 
-	WARN(HAS_PCH_IBX(dev_priv->dev) && (val & SDVO_PIPE_B_SELECT),
+	WARN(HAS_PCH_IBX(dev_priv->dev) && (val & DP_PORT_EN) == 0
+	     && (val & DP_PIPEB_SELECT),
 	     "IBX PCH dp port still using transcoder B\n");
 }
 
@@ -1388,7 +1389,8 @@
 	     "PCH HDMI (0x%08x) enabled on transcoder %c, should be disabled\n",
 	     reg, pipe_name(pipe));
 
-	WARN(HAS_PCH_IBX(dev_priv->dev) && (val & SDVO_PIPE_B_SELECT),
+	WARN(HAS_PCH_IBX(dev_priv->dev) && (val & PORT_ENABLE) == 0
+	     && (val & SDVO_PIPE_B_SELECT),
 	     "IBX PCH hdmi port still using transcoder B\n");
 }
 
diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index a6c426a..ace757a 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -2533,14 +2533,10 @@
 			break;
 	}
 
-	intel_dp_i2c_init(intel_dp, intel_connector, name);
-
 	/* Cache some DPCD data in the eDP case */
 	if (is_edp(intel_dp)) {
-		bool ret;
 		struct edp_power_seq	cur, vbt;
 		u32 pp_on, pp_off, pp_div;
-		struct edid *edid;
 
 		pp_on = I915_READ(PCH_PP_ON_DELAYS);
 		pp_off = I915_READ(PCH_PP_OFF_DELAYS);
@@ -2591,6 +2587,13 @@
 
 		DRM_DEBUG_KMS("backlight on delay %d, off delay %d\n",
 			      intel_dp->backlight_on_delay, intel_dp->backlight_off_delay);
+	}
+
+	intel_dp_i2c_init(intel_dp, intel_connector, name);
+
+	if (is_edp(intel_dp)) {
+		bool ret;
+		struct edid *edid;
 
 		ironlake_edp_panel_vdd_on(intel_dp);
 		ret = intel_dp_get_dpcd(intel_dp);
diff --git a/drivers/gpu/drm/i915/intel_panel.c b/drivers/gpu/drm/i915/intel_panel.c
index 3df4f5f..e019b23 100644
--- a/drivers/gpu/drm/i915/intel_panel.c
+++ b/drivers/gpu/drm/i915/intel_panel.c
@@ -162,19 +162,12 @@
 	return val;
 }
 
-u32 intel_panel_get_max_backlight(struct drm_device *dev)
+static u32 _intel_panel_get_max_backlight(struct drm_device *dev)
 {
 	struct drm_i915_private *dev_priv = dev->dev_private;
 	u32 max;
 
 	max = i915_read_blc_pwm_ctl(dev_priv);
-	if (max == 0) {
-		/* XXX add code here to query mode clock or hardware clock
-		 * and program max PWM appropriately.
-		 */
-		pr_warn_once("fixme: max PWM is zero\n");
-		return 1;
-	}
 
 	if (HAS_PCH_SPLIT(dev)) {
 		max >>= 16;
@@ -188,6 +181,22 @@
 			max *= 0xff;
 	}
 
+	return max;
+}
+
+u32 intel_panel_get_max_backlight(struct drm_device *dev)
+{
+	u32 max;
+
+	max = _intel_panel_get_max_backlight(dev);
+	if (max == 0) {
+		/* XXX add code here to query mode clock or hardware clock
+		 * and program max PWM appropriately.
+		 */
+		pr_warn_once("fixme: max PWM is zero\n");
+		return 1;
+	}
+
 	DRM_DEBUG_DRIVER("max backlight PWM = %d\n", max);
 	return max;
 }
@@ -424,7 +433,11 @@
 
 	memset(&props, 0, sizeof(props));
 	props.type = BACKLIGHT_RAW;
-	props.max_brightness = intel_panel_get_max_backlight(dev);
+	props.max_brightness = _intel_panel_get_max_backlight(dev);
+	if (props.max_brightness == 0) {
+		DRM_ERROR("Failed to get maximum backlight value\n");
+		return -ENODEV;
+	}
 	dev_priv->backlight =
 		backlight_device_register("intel_backlight",
 					  &connector->kdev, dev,
diff --git a/drivers/gpu/drm/i915/intel_pm.c b/drivers/gpu/drm/i915/intel_pm.c
index 1881c8c..ba8a27b 100644
--- a/drivers/gpu/drm/i915/intel_pm.c
+++ b/drivers/gpu/drm/i915/intel_pm.c
@@ -3672,6 +3672,9 @@
 
 	if (IS_PINEVIEW(dev))
 		I915_WRITE(ECOSKPD, _MASKED_BIT_ENABLE(ECO_GATING_CX_ONLY));
+
+	/* IIR "flip pending" means done if this bit is set */
+	I915_WRITE(ECOSKPD, _MASKED_BIT_DISABLE(ECO_FLIP_DONE));
 }
 
 static void i85x_init_clock_gating(struct drm_device *dev)
diff --git a/drivers/gpu/drm/i915/intel_sdvo.c b/drivers/gpu/drm/i915/intel_sdvo.c
index d81bb0b..123afd3 100644
--- a/drivers/gpu/drm/i915/intel_sdvo.c
+++ b/drivers/gpu/drm/i915/intel_sdvo.c
@@ -2573,7 +2573,6 @@
 		hotplug_mask = intel_sdvo->is_sdvob ?
 			SDVOB_HOTPLUG_INT_STATUS_I915 : SDVOC_HOTPLUG_INT_STATUS_I915;
 	}
-	dev_priv->hotplug_supported_mask |= hotplug_mask;
 
 	drm_encoder_helper_add(&intel_encoder->base, &intel_sdvo_helper_funcs);
 
@@ -2581,14 +2580,6 @@
 	if (!intel_sdvo_get_capabilities(intel_sdvo, &intel_sdvo->caps))
 		goto err;
 
-	/* Set up hotplug command - note paranoia about contents of reply.
-	 * We assume that the hardware is in a sane state, and only touch
-	 * the bits we think we understand.
-	 */
-	intel_sdvo_get_value(intel_sdvo, SDVO_CMD_GET_ACTIVE_HOT_PLUG,
-			     &intel_sdvo->hotplug_active, 2);
-	intel_sdvo->hotplug_active[0] &= ~0x3;
-
 	if (intel_sdvo_output_setup(intel_sdvo,
 				    intel_sdvo->caps.output_flags) != true) {
 		DRM_DEBUG_KMS("SDVO output failed to setup on %s\n",
@@ -2596,6 +2587,12 @@
 		goto err;
 	}
 
+	/* Only enable the hotplug irq if we need it, to work around noisy
+	 * hotplug lines.
+	 */
+	if (intel_sdvo->hotplug_active[0])
+		dev_priv->hotplug_supported_mask |= hotplug_mask;
+
 	intel_sdvo_select_ddc_bus(dev_priv, intel_sdvo, sdvo_reg);
 
 	/* Set the input timing to the screen. Assume always input 0. */
diff --git a/drivers/gpu/drm/mgag200/mgag200_drv.c b/drivers/gpu/drm/mgag200/mgag200_drv.c
index ea1024d..e5f145d 100644
--- a/drivers/gpu/drm/mgag200/mgag200_drv.c
+++ b/drivers/gpu/drm/mgag200/mgag200_drv.c
@@ -84,6 +84,9 @@
 	.mmap = mgag200_mmap,
 	.poll = drm_poll,
 	.fasync = drm_fasync,
+#ifdef CONFIG_COMPAT
+	.compat_ioctl = drm_compat_ioctl,
+#endif
 	.read = drm_read,
 };
 
diff --git a/drivers/gpu/drm/nouveau/nouveau_display.c b/drivers/gpu/drm/nouveau/nouveau_display.c
index 69688ef..7e16dc5 100644
--- a/drivers/gpu/drm/nouveau/nouveau_display.c
+++ b/drivers/gpu/drm/nouveau/nouveau_display.c
@@ -598,7 +598,7 @@
 	args->size = args->pitch * args->height;
 	args->size = roundup(args->size, PAGE_SIZE);
 
-	ret = nouveau_gem_new(dev, args->size, 0, TTM_PL_FLAG_VRAM, 0, 0, &bo);
+	ret = nouveau_gem_new(dev, args->size, 0, NOUVEAU_GEM_DOMAIN_VRAM, 0, 0, &bo);
 	if (ret)
 		return ret;
 
diff --git a/drivers/gpu/drm/nouveau/nv50_gpio.c b/drivers/gpu/drm/nouveau/nv50_gpio.c
index f429e6a..f034905 100644
--- a/drivers/gpu/drm/nouveau/nv50_gpio.c
+++ b/drivers/gpu/drm/nouveau/nv50_gpio.c
@@ -115,6 +115,9 @@
 {
 	struct drm_nouveau_private *dev_priv = dev->dev_private;
 
+	/* initialise gpios and routing to vbios defaults */
+	nouveau_gpio_reset(dev);
+
 	/* disable, and ack any pending gpio interrupts */
 	nv_wr32(dev, 0xe050, 0x00000000);
 	nv_wr32(dev, 0xe054, 0xffffffff);
diff --git a/drivers/gpu/drm/nouveau/nvd0_display.c b/drivers/gpu/drm/nouveau/nvd0_display.c
index dac525b..8a2fc89 100644
--- a/drivers/gpu/drm/nouveau/nvd0_display.c
+++ b/drivers/gpu/drm/nouveau/nvd0_display.c
@@ -1510,10 +1510,10 @@
 	case OUTPUT_DP:
 		if (nv_connector->base.display_info.bpc == 6) {
 			nv_encoder->dp.datarate = mode->clock * 18 / 8;
-			syncs |= 0x00000140;
+			syncs |= 0x00000002 << 6;
 		} else {
 			nv_encoder->dp.datarate = mode->clock * 24 / 8;
-			syncs |= 0x00000180;
+			syncs |= 0x00000005 << 6;
 		}
 
 		if (nv_encoder->dcb->sorconf.link & 1)
diff --git a/drivers/gpu/drm/radeon/atombios_crtc.c b/drivers/gpu/drm/radeon/atombios_crtc.c
index 2817101..e721e30 100644
--- a/drivers/gpu/drm/radeon/atombios_crtc.c
+++ b/drivers/gpu/drm/radeon/atombios_crtc.c
@@ -1479,14 +1479,98 @@
 	}
 }
 
+/**
+ * radeon_get_pll_use_mask - look up a mask of which pplls are in use
+ *
+ * @crtc: drm crtc
+ *
+ * Returns the mask of which PPLLs (Pixel PLLs) are in use.
+ */
+static u32 radeon_get_pll_use_mask(struct drm_crtc *crtc)
+{
+	struct drm_device *dev = crtc->dev;
+	struct drm_crtc *test_crtc;
+	struct radeon_crtc *radeon_test_crtc;
+	u32 pll_in_use = 0;
+
+	list_for_each_entry(test_crtc, &dev->mode_config.crtc_list, head) {
+		if (crtc == test_crtc)
+			continue;
+
+		radeon_test_crtc = to_radeon_crtc(test_crtc);
+		if (radeon_test_crtc->pll_id != ATOM_PPLL_INVALID)
+			pll_in_use |= (1 << radeon_test_crtc->pll_id);
+	}
+	return pll_in_use;
+}
+
+/**
+ * radeon_get_shared_dp_ppll - return the PPLL used by another crtc for DP
+ *
+ * @crtc: drm crtc
+ *
+ * Returns the PPLL (Pixel PLL) used by another crtc/encoder which is
+ * also in DP mode.  For DP, a single PPLL can be used for all DP
+ * crtcs/encoders.
+ */
+static int radeon_get_shared_dp_ppll(struct drm_crtc *crtc)
+{
+	struct drm_device *dev = crtc->dev;
+	struct drm_encoder *test_encoder;
+	struct radeon_crtc *radeon_test_crtc;
+
+	list_for_each_entry(test_encoder, &dev->mode_config.encoder_list, head) {
+		if (test_encoder->crtc && (test_encoder->crtc != crtc)) {
+			if (ENCODER_MODE_IS_DP(atombios_get_encoder_mode(test_encoder))) {
+				/* for DP use the same PLL for all */
+				radeon_test_crtc = to_radeon_crtc(test_encoder->crtc);
+				if (radeon_test_crtc->pll_id != ATOM_PPLL_INVALID)
+					return radeon_test_crtc->pll_id;
+			}
+		}
+	}
+	return ATOM_PPLL_INVALID;
+}
+
+/**
+ * radeon_atom_pick_pll - Allocate a PPLL for use by the crtc.
+ *
+ * @crtc: drm crtc
+ *
+ * Returns the PPLL (Pixel PLL) to be used by the crtc.  For DP monitors
+ * a single PPLL can be used for all DP crtcs/encoders.  For non-DP
+ * monitors a dedicated PPLL must be used.  If a particular board has
+ * an external DP PLL, return ATOM_PPLL_INVALID to skip PLL programming
+ * as there is no need to program the PLL itself.  If we are not able to
+ * allocate a PLL, return ATOM_PPLL_INVALID to skip PLL programming to
+ * avoid messing up an existing monitor.
+ *
+ * Asic specific PLL information
+ *
+ * DCE 6.1
+ * - PPLL2 is only available to UNIPHYA (both DP and non-DP)
+ * - PPLL0, PPLL1 are available for UNIPHYB/C/D/E/F (both DP and non-DP)
+ *
+ * DCE 6.0
+ * - PPLL0 is available to all UNIPHY (DP only)
+ * - PPLL1, PPLL2 are available for all UNIPHY (both DP and non-DP) and DAC
+ *
+ * DCE 5.0
+ * - DCPLL is available to all UNIPHY (DP only)
+ * - PPLL1, PPLL2 are available for all UNIPHY (both DP and non-DP) and DAC
+ *
+ * DCE 3.0/4.0/4.1
+ * - PPLL1, PPLL2 are available for all UNIPHY (both DP and non-DP) and DAC
+ *
+ */
 static int radeon_atom_pick_pll(struct drm_crtc *crtc)
 {
 	struct radeon_crtc *radeon_crtc = to_radeon_crtc(crtc);
 	struct drm_device *dev = crtc->dev;
 	struct radeon_device *rdev = dev->dev_private;
 	struct drm_encoder *test_encoder;
-	struct drm_crtc *test_crtc;
-	uint32_t pll_in_use = 0;
+	u32 pll_in_use;
+	int pll;
 
 	if (ASIC_IS_DCE61(rdev)) {
 		list_for_each_entry(test_encoder, &dev->mode_config.encoder_list, head) {
@@ -1498,32 +1582,40 @@
 
 				if ((test_radeon_encoder->encoder_id ==
 				     ENCODER_OBJECT_ID_INTERNAL_UNIPHY) &&
-				    (dig->linkb == false)) /* UNIPHY A uses PPLL2 */
+				    (dig->linkb == false))
+					/* UNIPHY A uses PPLL2 */
 					return ATOM_PPLL2;
+				else if (ENCODER_MODE_IS_DP(atombios_get_encoder_mode(test_encoder))) {
+					/* UNIPHY B/C/D/E/F */
+					if (rdev->clock.dp_extclk)
+						/* skip PPLL programming if using ext clock */
+						return ATOM_PPLL_INVALID;
+					else {
+						/* use the same PPLL for all DP monitors */
+						pll = radeon_get_shared_dp_ppll(crtc);
+						if (pll != ATOM_PPLL_INVALID)
+							return pll;
+					}
+				}
+				break;
 			}
 		}
 		/* UNIPHY B/C/D/E/F */
-		list_for_each_entry(test_crtc, &dev->mode_config.crtc_list, head) {
-			struct radeon_crtc *radeon_test_crtc;
-
-			if (crtc == test_crtc)
-				continue;
-
-			radeon_test_crtc = to_radeon_crtc(test_crtc);
-			if ((radeon_test_crtc->pll_id == ATOM_PPLL0) ||
-			    (radeon_test_crtc->pll_id == ATOM_PPLL1))
-				pll_in_use |= (1 << radeon_test_crtc->pll_id);
-		}
-		if (!(pll_in_use & 4))
+		pll_in_use = radeon_get_pll_use_mask(crtc);
+		if (!(pll_in_use & (1 << ATOM_PPLL0)))
 			return ATOM_PPLL0;
-		return ATOM_PPLL1;
+		if (!(pll_in_use & (1 << ATOM_PPLL1)))
+			return ATOM_PPLL1;
+		DRM_ERROR("unable to allocate a PPLL\n");
+		return ATOM_PPLL_INVALID;
 	} else if (ASIC_IS_DCE4(rdev)) {
 		list_for_each_entry(test_encoder, &dev->mode_config.encoder_list, head) {
 			if (test_encoder->crtc && (test_encoder->crtc == crtc)) {
 				/* in DP mode, the DP ref clock can come from PPLL, DCPLL, or ext clock,
 				 * depending on the asic:
 				 * DCE4: PPLL or ext clock
-				 * DCE5: DCPLL or ext clock
+				 * DCE5: PPLL, DCPLL, or ext clock
+				 * DCE6: PPLL, PPLL0, or ext clock
 				 *
 				 * Setting ATOM_PPLL_INVALID will cause SetPixelClock to skip
 				 * PPLL/DCPLL programming and only program the DP DTO for the
@@ -1531,31 +1623,34 @@
 				 */
 				if (ENCODER_MODE_IS_DP(atombios_get_encoder_mode(test_encoder))) {
 					if (rdev->clock.dp_extclk)
+						/* skip PPLL programming if using ext clock */
 						return ATOM_PPLL_INVALID;
 					else if (ASIC_IS_DCE6(rdev))
+						/* use PPLL0 for all DP */
 						return ATOM_PPLL0;
 					else if (ASIC_IS_DCE5(rdev))
+						/* use DCPLL for all DP */
 						return ATOM_DCPLL;
+					else {
+						/* use the same PPLL for all DP monitors */
+						pll = radeon_get_shared_dp_ppll(crtc);
+						if (pll != ATOM_PPLL_INVALID)
+							return pll;
+					}
 				}
+				break;
 			}
 		}
-
-		/* otherwise, pick one of the plls */
-		list_for_each_entry(test_crtc, &dev->mode_config.crtc_list, head) {
-			struct radeon_crtc *radeon_test_crtc;
-
-			if (crtc == test_crtc)
-				continue;
-
-			radeon_test_crtc = to_radeon_crtc(test_crtc);
-			if ((radeon_test_crtc->pll_id >= ATOM_PPLL1) &&
-			    (radeon_test_crtc->pll_id <= ATOM_PPLL2))
-				pll_in_use |= (1 << radeon_test_crtc->pll_id);
-		}
-		if (!(pll_in_use & 1))
+		/* all other cases */
+		pll_in_use = radeon_get_pll_use_mask(crtc);
+		if (!(pll_in_use & (1 << ATOM_PPLL2)))
+			return ATOM_PPLL2;
+		if (!(pll_in_use & (1 << ATOM_PPLL1)))
 			return ATOM_PPLL1;
-		return ATOM_PPLL2;
+		DRM_ERROR("unable to allocate a PPLL\n");
+		return ATOM_PPLL_INVALID;
 	} else
+		/* use PPLL1 or PPLL2 */
 		return radeon_crtc->crtc_id;
 
 }
@@ -1697,7 +1792,7 @@
 		break;
 	}
 done:
-	radeon_crtc->pll_id = -1;
+	radeon_crtc->pll_id = ATOM_PPLL_INVALID;
 }
 
 static const struct drm_crtc_helper_funcs atombios_helper_funcs = {
@@ -1746,6 +1841,6 @@
 		else
 			radeon_crtc->crtc_offset = 0;
 	}
-	radeon_crtc->pll_id = -1;
+	radeon_crtc->pll_id = ATOM_PPLL_INVALID;
 	drm_crtc_helper_add(&radeon_crtc->base, &atombios_helper_funcs);
 }
diff --git a/drivers/gpu/drm/radeon/radeon_fence.c b/drivers/gpu/drm/radeon/radeon_fence.c
index 7b737b9..2a59375 100644
--- a/drivers/gpu/drm/radeon/radeon_fence.c
+++ b/drivers/gpu/drm/radeon/radeon_fence.c
@@ -131,7 +131,7 @@
  */
 void radeon_fence_process(struct radeon_device *rdev, int ring)
 {
-	uint64_t seq, last_seq;
+	uint64_t seq, last_seq, last_emitted;
 	unsigned count_loop = 0;
 	bool wake = false;
 
@@ -158,13 +158,15 @@
 	 */
 	last_seq = atomic64_read(&rdev->fence_drv[ring].last_seq);
 	do {
+		last_emitted = rdev->fence_drv[ring].sync_seq[ring];
 		seq = radeon_fence_read(rdev, ring);
 		seq |= last_seq & 0xffffffff00000000LL;
 		if (seq < last_seq) {
-			seq += 0x100000000LL;
+			seq &= 0xffffffff;
+			seq |= last_emitted & 0xffffffff00000000LL;
 		}
 
-		if (seq == last_seq) {
+		if (seq <= last_seq || seq > last_emitted) {
 			break;
 		}
 		/* If we loop over we don't want to return without
diff --git a/drivers/gpu/drm/savage/savage_drv.c b/drivers/gpu/drm/savage/savage_drv.c
index d31d4cc..c5a1643 100644
--- a/drivers/gpu/drm/savage/savage_drv.c
+++ b/drivers/gpu/drm/savage/savage_drv.c
@@ -43,6 +43,9 @@
 	.mmap = drm_mmap,
 	.poll = drm_poll,
 	.fasync = drm_fasync,
+#ifdef CONFIG_COMPAT
+	.compat_ioctl = drm_compat_ioctl,
+#endif
 	.llseek = noop_llseek,
 };
 
diff --git a/drivers/gpu/drm/sis/sis_drv.c b/drivers/gpu/drm/sis/sis_drv.c
index 7f11987..867dc03 100644
--- a/drivers/gpu/drm/sis/sis_drv.c
+++ b/drivers/gpu/drm/sis/sis_drv.c
@@ -74,6 +74,9 @@
 	.mmap = drm_mmap,
 	.poll = drm_poll,
 	.fasync = drm_fasync,
+#ifdef CONFIG_COMPAT
+	.compat_ioctl = drm_compat_ioctl,
+#endif
 	.llseek = noop_llseek,
 };
 
diff --git a/drivers/gpu/drm/tdfx/tdfx_drv.c b/drivers/gpu/drm/tdfx/tdfx_drv.c
index 90f6b13..a7f4d6b 100644
--- a/drivers/gpu/drm/tdfx/tdfx_drv.c
+++ b/drivers/gpu/drm/tdfx/tdfx_drv.c
@@ -49,6 +49,9 @@
 	.mmap = drm_mmap,
 	.poll = drm_poll,
 	.fasync = drm_fasync,
+#ifdef CONFIG_COMPAT
+	.compat_ioctl = drm_compat_ioctl,
+#endif
 	.llseek = noop_llseek,
 };
 
diff --git a/drivers/gpu/drm/udl/udl_drv.c b/drivers/gpu/drm/udl/udl_drv.c
index 6e52069..9f84128 100644
--- a/drivers/gpu/drm/udl/udl_drv.c
+++ b/drivers/gpu/drm/udl/udl_drv.c
@@ -66,6 +66,9 @@
 	.unlocked_ioctl	= drm_ioctl,
 	.release = drm_release,
 	.fasync = drm_fasync,
+#ifdef CONFIG_COMPAT
+	.compat_ioctl = drm_compat_ioctl,
+#endif
 	.llseek = noop_llseek,
 };
 
diff --git a/drivers/gpu/drm/via/via_drv.c b/drivers/gpu/drm/via/via_drv.c
index e927b4c..af1b914 100644
--- a/drivers/gpu/drm/via/via_drv.c
+++ b/drivers/gpu/drm/via/via_drv.c
@@ -65,6 +65,9 @@
 	.mmap = drm_mmap,
 	.poll = drm_poll,
 	.fasync = drm_fasync,
+#ifdef CONFIG_COMPAT
+	.compat_ioctl = drm_compat_ioctl,
+#endif
 	.llseek = noop_llseek,
 };
 
diff --git a/drivers/gpu/drm/vmwgfx/Kconfig b/drivers/gpu/drm/vmwgfx/Kconfig
index 794ff67..b71bcd0 100644
--- a/drivers/gpu/drm/vmwgfx/Kconfig
+++ b/drivers/gpu/drm/vmwgfx/Kconfig
@@ -12,3 +12,11 @@
 	  This is a KMS enabled DRM driver for the VMware SVGA2
 	  virtual hardware.
 	  The compiled module will be called "vmwgfx.ko".
+
+config DRM_VMWGFX_FBCON
+	depends on DRM_VMWGFX
+	bool "Enable framebuffer console under vmwgfx by default"
+	help
+	   Choose this option if you are shipping a new vmwgfx
+	   userspace driver that supports using the kernel driver.
+
diff --git a/drivers/gpu/drm/vmwgfx/vmwgfx_drv.c b/drivers/gpu/drm/vmwgfx/vmwgfx_drv.c
index 4d9edea..ba2c35d 100644
--- a/drivers/gpu/drm/vmwgfx/vmwgfx_drv.c
+++ b/drivers/gpu/drm/vmwgfx/vmwgfx_drv.c
@@ -182,8 +182,9 @@
 	{0x15ad, 0x0405, PCI_ANY_ID, PCI_ANY_ID, 0, 0, VMWGFX_CHIP_SVGAII},
 	{0, 0, 0}
 };
+MODULE_DEVICE_TABLE(pci, vmw_pci_id_list);
 
-static int enable_fbdev;
+static int enable_fbdev = IS_ENABLED(CONFIG_DRM_VMWGFX_FBCON);
 
 static int vmw_probe(struct pci_dev *, const struct pci_device_id *);
 static void vmw_master_init(struct vmw_master *);
@@ -1154,6 +1155,11 @@
 	.open = vmw_driver_open,
 	.preclose = vmw_preclose,
 	.postclose = vmw_postclose,
+
+	.dumb_create = vmw_dumb_create,
+	.dumb_map_offset = vmw_dumb_map_offset,
+	.dumb_destroy = vmw_dumb_destroy,
+
 	.fops = &vmwgfx_driver_fops,
 	.name = VMWGFX_DRIVER_NAME,
 	.desc = VMWGFX_DRIVER_DESC,
diff --git a/drivers/gpu/drm/vmwgfx/vmwgfx_drv.h b/drivers/gpu/drm/vmwgfx/vmwgfx_drv.h
index d0f2c07..29c984f 100644
--- a/drivers/gpu/drm/vmwgfx/vmwgfx_drv.h
+++ b/drivers/gpu/drm/vmwgfx/vmwgfx_drv.h
@@ -645,6 +645,16 @@
 int vmw_kms_update_layout_ioctl(struct drm_device *dev, void *data,
 				struct drm_file *file_priv);
 
+int vmw_dumb_create(struct drm_file *file_priv,
+		    struct drm_device *dev,
+		    struct drm_mode_create_dumb *args);
+
+int vmw_dumb_map_offset(struct drm_file *file_priv,
+			struct drm_device *dev, uint32_t handle,
+			uint64_t *offset);
+int vmw_dumb_destroy(struct drm_file *file_priv,
+		     struct drm_device *dev,
+		     uint32_t handle);
 /**
  * Overlay control - vmwgfx_overlay.c
  */
diff --git a/drivers/gpu/drm/vmwgfx/vmwgfx_resource.c b/drivers/gpu/drm/vmwgfx/vmwgfx_resource.c
index 22bf9a2..2c6ffe0 100644
--- a/drivers/gpu/drm/vmwgfx/vmwgfx_resource.c
+++ b/drivers/gpu/drm/vmwgfx/vmwgfx_resource.c
@@ -1917,3 +1917,76 @@
 	vmw_resource_unreference(&res);
 	return ret;
 }
+
+
+int vmw_dumb_create(struct drm_file *file_priv,
+		    struct drm_device *dev,
+		    struct drm_mode_create_dumb *args)
+{
+	struct vmw_private *dev_priv = vmw_priv(dev);
+	struct vmw_master *vmaster = vmw_master(file_priv->master);
+	struct vmw_user_dma_buffer *vmw_user_bo;
+	struct ttm_buffer_object *tmp;
+	int ret;
+
+	args->pitch = args->width * ((args->bpp + 7) / 8);
+	args->size = args->pitch * args->height;
+
+	vmw_user_bo = kzalloc(sizeof(*vmw_user_bo), GFP_KERNEL);
+	if (vmw_user_bo == NULL)
+		return -ENOMEM;
+
+	ret = ttm_read_lock(&vmaster->lock, true);
+	if (ret != 0) {
+		kfree(vmw_user_bo);
+		return ret;
+	}
+
+	ret = vmw_dmabuf_init(dev_priv, &vmw_user_bo->dma, args->size,
+			      &vmw_vram_sys_placement, true,
+			      &vmw_user_dmabuf_destroy);
+	if (ret != 0)
+		goto out_no_dmabuf;
+
+	tmp = ttm_bo_reference(&vmw_user_bo->dma.base);
+	ret = ttm_base_object_init(vmw_fpriv(file_priv)->tfile,
+				   &vmw_user_bo->base,
+				   false,
+				   ttm_buffer_type,
+				   &vmw_user_dmabuf_release, NULL);
+	if (unlikely(ret != 0))
+		goto out_no_base_object;
+
+	args->handle = vmw_user_bo->base.hash.key;
+
+out_no_base_object:
+	ttm_bo_unref(&tmp);
+out_no_dmabuf:
+	ttm_read_unlock(&vmaster->lock);
+	return ret;
+}
+
+int vmw_dumb_map_offset(struct drm_file *file_priv,
+			struct drm_device *dev, uint32_t handle,
+			uint64_t *offset)
+{
+	struct ttm_object_file *tfile = vmw_fpriv(file_priv)->tfile;
+	struct vmw_dma_buffer *out_buf;
+	int ret;
+
+	ret = vmw_user_dmabuf_lookup(tfile, handle, &out_buf);
+	if (ret != 0)
+		return -EINVAL;
+
+	*offset = out_buf->base.addr_space_offset;
+	vmw_dmabuf_unreference(&out_buf);
+	return 0;
+}
+
+int vmw_dumb_destroy(struct drm_file *file_priv,
+		     struct drm_device *dev,
+		     uint32_t handle)
+{
+	return ttm_ref_object_base_unref(vmw_fpriv(file_priv)->tfile,
+					 handle, TTM_REF_USAGE);
+}
diff --git a/drivers/hid/hid-core.c b/drivers/hid/hid-core.c
index 8bf8a64..8bcd168 100644
--- a/drivers/hid/hid-core.c
+++ b/drivers/hid/hid-core.c
@@ -996,7 +996,8 @@
 	struct hid_driver *hdrv = hid->driver;
 	int ret;
 
-	hid_dump_input(hid, usage, value);
+	if (!list_empty(&hid->debug_list))
+		hid_dump_input(hid, usage, value);
 
 	if (hdrv && hdrv->event && hid_match_usage(hid, usage)) {
 		ret = hdrv->event(hid, field, usage, value);
@@ -1558,7 +1559,9 @@
 	{ HID_USB_DEVICE(USB_VENDOR_ID_KYE, USB_DEVICE_ID_KYE_EASYPEN_M610X) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LABTEC, USB_DEVICE_ID_LABTEC_WIRELESS_KEYBOARD) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LCPOWER, USB_DEVICE_ID_LCPOWER_LC1000 ) },
- 	{ HID_USB_DEVICE(USB_VENDOR_ID_LENOVO, USB_DEVICE_ID_LENOVO_TPKBD) },
+#if IS_ENABLED(CONFIG_HID_LENOVO_TPKBD)
+	{ HID_USB_DEVICE(USB_VENDOR_ID_LENOVO, USB_DEVICE_ID_LENOVO_TPKBD) },
+#endif
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_MX3000_RECEIVER) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_S510_RECEIVER) },
 	{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_S510_RECEIVER_2) },
diff --git a/drivers/hid/hid-logitech-dj.c b/drivers/hid/hid-logitech-dj.c
index 0f9c146..4d524b5 100644
--- a/drivers/hid/hid-logitech-dj.c
+++ b/drivers/hid/hid-logitech-dj.c
@@ -439,7 +439,7 @@
 	struct dj_report *dj_report;
 	int retval;
 
-	dj_report = kzalloc(sizeof(dj_report), GFP_KERNEL);
+	dj_report = kzalloc(sizeof(struct dj_report), GFP_KERNEL);
 	if (!dj_report)
 		return -ENOMEM;
 	dj_report->report_id = REPORT_ID_DJ_SHORT;
@@ -456,7 +456,7 @@
 	struct dj_report *dj_report;
 	int retval;
 
-	dj_report = kzalloc(sizeof(dj_report), GFP_KERNEL);
+	dj_report = kzalloc(sizeof(struct dj_report), GFP_KERNEL);
 	if (!dj_report)
 		return -ENOMEM;
 	dj_report->report_id = REPORT_ID_DJ_SHORT;
diff --git a/drivers/hid/usbhid/hid-quirks.c b/drivers/hid/usbhid/hid-quirks.c
index 903eef3..991e85c 100644
--- a/drivers/hid/usbhid/hid-quirks.c
+++ b/drivers/hid/usbhid/hid-quirks.c
@@ -70,6 +70,7 @@
 	{ USB_VENDOR_ID_CH, USB_DEVICE_ID_CH_AXIS_295, HID_QUIRK_NOGET },
 	{ USB_VENDOR_ID_DMI, USB_DEVICE_ID_DMI_ENC, HID_QUIRK_NOGET },
 	{ USB_VENDOR_ID_ELO, USB_DEVICE_ID_ELO_TS2700, HID_QUIRK_NOGET },
+	{ USB_VENDOR_ID_MGE, USB_DEVICE_ID_MGE_UPS, HID_QUIRK_NOGET },
 	{ USB_VENDOR_ID_PIXART, USB_DEVICE_ID_PIXART_OPTICAL_TOUCH_SCREEN, HID_QUIRK_NO_INIT_REPORTS },
 	{ USB_VENDOR_ID_PIXART, USB_DEVICE_ID_PIXART_OPTICAL_TOUCH_SCREEN1, HID_QUIRK_NO_INIT_REPORTS },
 	{ USB_VENDOR_ID_PIXART, USB_DEVICE_ID_PIXART_OPTICAL_TOUCH_SCREEN2, HID_QUIRK_NO_INIT_REPORTS },
diff --git a/drivers/hwmon/ina2xx.c b/drivers/hwmon/ina2xx.c
index 7f3f4a3..6021482 100644
--- a/drivers/hwmon/ina2xx.c
+++ b/drivers/hwmon/ina2xx.c
@@ -69,22 +69,6 @@
 	u16 regs[INA2XX_MAX_REGISTERS];
 };
 
-int ina2xx_read_word(struct i2c_client *client, int reg)
-{
-	int val = i2c_smbus_read_word_data(client, reg);
-	if (unlikely(val < 0)) {
-		dev_dbg(&client->dev,
-			"Failed to read register: %d\n", reg);
-		return val;
-	}
-	return be16_to_cpu(val);
-}
-
-void ina2xx_write_word(struct i2c_client *client, int reg, int data)
-{
-	i2c_smbus_write_word_data(client, reg, cpu_to_be16(data));
-}
-
 static struct ina2xx_data *ina2xx_update_device(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
@@ -102,7 +86,7 @@
 
 		/* Read all registers */
 		for (i = 0; i < data->registers; i++) {
-			int rv = ina2xx_read_word(client, i);
+			int rv = i2c_smbus_read_word_swapped(client, i);
 			if (rv < 0) {
 				ret = ERR_PTR(rv);
 				goto abort;
@@ -279,22 +263,26 @@
 	switch (data->kind) {
 	case ina219:
 		/* device configuration */
-		ina2xx_write_word(client, INA2XX_CONFIG, INA219_CONFIG_DEFAULT);
+		i2c_smbus_write_word_swapped(client, INA2XX_CONFIG,
+					     INA219_CONFIG_DEFAULT);
 
 		/* set current LSB to 1mA, shunt is in uOhms */
 		/* (equation 13 in datasheet) */
-		ina2xx_write_word(client, INA2XX_CALIBRATION, 40960000 / shunt);
+		i2c_smbus_write_word_swapped(client, INA2XX_CALIBRATION,
+					     40960000 / shunt);
 		dev_info(&client->dev,
 			 "power monitor INA219 (Rshunt = %li uOhm)\n", shunt);
 		data->registers = INA219_REGISTERS;
 		break;
 	case ina226:
 		/* device configuration */
-		ina2xx_write_word(client, INA2XX_CONFIG, INA226_CONFIG_DEFAULT);
+		i2c_smbus_write_word_swapped(client, INA2XX_CONFIG,
+					     INA226_CONFIG_DEFAULT);
 
 		/* set current LSB to 1mA, shunt is in uOhms */
 		/* (equation 1 in datasheet)*/
-		ina2xx_write_word(client, INA2XX_CALIBRATION, 5120000 / shunt);
+		i2c_smbus_write_word_swapped(client, INA2XX_CALIBRATION,
+					     5120000 / shunt);
 		dev_info(&client->dev,
 			 "power monitor INA226 (Rshunt = %li uOhm)\n", shunt);
 		data->registers = INA226_REGISTERS;
diff --git a/drivers/hwmon/twl4030-madc-hwmon.c b/drivers/hwmon/twl4030-madc-hwmon.c
index 0018c7d..1a174f0 100644
--- a/drivers/hwmon/twl4030-madc-hwmon.c
+++ b/drivers/hwmon/twl4030-madc-hwmon.c
@@ -44,12 +44,13 @@
 			 struct device_attribute *devattr, char *buf)
 {
 	struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
-	struct twl4030_madc_request req;
+	struct twl4030_madc_request req = {
+		.channels = 1 << attr->index,
+		.method = TWL4030_MADC_SW2,
+		.type = TWL4030_MADC_WAIT,
+	};
 	long val;
 
-	req.channels = (1 << attr->index);
-	req.method = TWL4030_MADC_SW2;
-	req.func_cb = NULL;
 	val = twl4030_madc_conversion(&req);
 	if (val < 0)
 		return val;
diff --git a/drivers/i2c/algos/i2c-algo-pca.c b/drivers/i2c/algos/i2c-algo-pca.c
index 73133b1..6f5f98d 100644
--- a/drivers/i2c/algos/i2c-algo-pca.c
+++ b/drivers/i2c/algos/i2c-algo-pca.c
@@ -476,17 +476,17 @@
 		/* To avoid integer overflow, use clock/100 for calculations */
 		clock = pca_clock(pca_data) / 100;
 
-		if (pca_data->i2c_clock > 10000) {
+		if (pca_data->i2c_clock > 1000000) {
 			mode = I2C_PCA_MODE_TURBO;
 			min_tlow = 14;
 			min_thi  = 5;
 			raise_fall_time = 22; /* Raise 11e-8s, Fall 11e-8s */
-		} else if (pca_data->i2c_clock > 4000) {
+		} else if (pca_data->i2c_clock > 400000) {
 			mode = I2C_PCA_MODE_FASTP;
 			min_tlow = 17;
 			min_thi  = 9;
 			raise_fall_time = 22; /* Raise 11e-8s, Fall 11e-8s */
-		} else if (pca_data->i2c_clock > 1000) {
+		} else if (pca_data->i2c_clock > 100000) {
 			mode = I2C_PCA_MODE_FAST;
 			min_tlow = 44;
 			min_thi  = 20;
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index b4aaa1b..970a161 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -104,6 +104,7 @@
 	    DH89xxCC (PCH)
 	    Panther Point (PCH)
 	    Lynx Point (PCH)
+	    Lynx Point-LP (PCH)
 
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-i801.
@@ -354,9 +355,13 @@
 	  devices such as DaVinci NIC.
 	  For details please see http://www.ti.com/davinci
 
+config I2C_DESIGNWARE_CORE
+	tristate
+
 config I2C_DESIGNWARE_PLATFORM
 	tristate "Synopsys DesignWare Platform"
 	depends on HAVE_CLK
+	select I2C_DESIGNWARE_CORE
 	help
 	  If you say yes to this option, support will be included for the
 	  Synopsys DesignWare I2C adapter. Only master mode is supported.
@@ -367,6 +372,7 @@
 config I2C_DESIGNWARE_PCI
 	tristate "Synopsys DesignWare PCI"
 	depends on PCI
+	select I2C_DESIGNWARE_CORE
 	help
 	  If you say yes to this option, support will be included for the
 	  Synopsys DesignWare I2C adapter. Only master mode is supported.
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index ce3c2be..37c4182 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -33,10 +33,11 @@
 obj-$(CONFIG_I2C_BLACKFIN_TWI)	+= i2c-bfin-twi.o
 obj-$(CONFIG_I2C_CPM)		+= i2c-cpm.o
 obj-$(CONFIG_I2C_DAVINCI)	+= i2c-davinci.o
+obj-$(CONFIG_I2C_DESIGNWARE_CORE)	+= i2c-designware-core.o
 obj-$(CONFIG_I2C_DESIGNWARE_PLATFORM)	+= i2c-designware-platform.o
-i2c-designware-platform-objs := i2c-designware-platdrv.o i2c-designware-core.o
+i2c-designware-platform-objs := i2c-designware-platdrv.o
 obj-$(CONFIG_I2C_DESIGNWARE_PCI)	+= i2c-designware-pci.o
-i2c-designware-pci-objs := i2c-designware-pcidrv.o i2c-designware-core.o
+i2c-designware-pci-objs := i2c-designware-pcidrv.o
 obj-$(CONFIG_I2C_EG20T)		+= i2c-eg20t.o
 obj-$(CONFIG_I2C_GPIO)		+= i2c-gpio.o
 obj-$(CONFIG_I2C_HIGHLANDER)	+= i2c-highlander.o
diff --git a/drivers/i2c/busses/i2c-designware-core.c b/drivers/i2c/busses/i2c-designware-core.c
index 1e48bec..7b8ebbe 100644
--- a/drivers/i2c/busses/i2c-designware-core.c
+++ b/drivers/i2c/busses/i2c-designware-core.c
@@ -25,6 +25,7 @@
  * ----------------------------------------------------------------------------
  *
  */
+#include <linux/export.h>
 #include <linux/clk.h>
 #include <linux/errno.h>
 #include <linux/err.h>
@@ -316,6 +317,7 @@
 	dw_writel(dev, dev->master_cfg , DW_IC_CON);
 	return 0;
 }
+EXPORT_SYMBOL_GPL(i2c_dw_init);
 
 /*
  * Waiting for bus not busy
@@ -568,12 +570,14 @@
 
 	return ret;
 }
+EXPORT_SYMBOL_GPL(i2c_dw_xfer);
 
 u32 i2c_dw_func(struct i2c_adapter *adap)
 {
 	struct dw_i2c_dev *dev = i2c_get_adapdata(adap);
 	return dev->functionality;
 }
+EXPORT_SYMBOL_GPL(i2c_dw_func);
 
 static u32 i2c_dw_read_clear_intrbits(struct dw_i2c_dev *dev)
 {
@@ -678,17 +682,20 @@
 
 	return IRQ_HANDLED;
 }
+EXPORT_SYMBOL_GPL(i2c_dw_isr);
 
 void i2c_dw_enable(struct dw_i2c_dev *dev)
 {
        /* Enable the adapter */
 	dw_writel(dev, 1, DW_IC_ENABLE);
 }
+EXPORT_SYMBOL_GPL(i2c_dw_enable);
 
 u32 i2c_dw_is_enabled(struct dw_i2c_dev *dev)
 {
 	return dw_readl(dev, DW_IC_ENABLE);
 }
+EXPORT_SYMBOL_GPL(i2c_dw_is_enabled);
 
 void i2c_dw_disable(struct dw_i2c_dev *dev)
 {
@@ -699,18 +706,22 @@
 	dw_writel(dev, 0, DW_IC_INTR_MASK);
 	dw_readl(dev, DW_IC_CLR_INTR);
 }
+EXPORT_SYMBOL_GPL(i2c_dw_disable);
 
 void i2c_dw_clear_int(struct dw_i2c_dev *dev)
 {
 	dw_readl(dev, DW_IC_CLR_INTR);
 }
+EXPORT_SYMBOL_GPL(i2c_dw_clear_int);
 
 void i2c_dw_disable_int(struct dw_i2c_dev *dev)
 {
 	dw_writel(dev, 0, DW_IC_INTR_MASK);
 }
+EXPORT_SYMBOL_GPL(i2c_dw_disable_int);
 
 u32 i2c_dw_read_comp_param(struct dw_i2c_dev *dev)
 {
 	return dw_readl(dev, DW_IC_COMP_PARAM_1);
 }
+EXPORT_SYMBOL_GPL(i2c_dw_read_comp_param);
diff --git a/drivers/i2c/busses/i2c-i801.c b/drivers/i2c/busses/i2c-i801.c
index 898dcf9..33e9b0c 100644
--- a/drivers/i2c/busses/i2c-i801.c
+++ b/drivers/i2c/busses/i2c-i801.c
@@ -52,6 +52,7 @@
   DH89xxCC (PCH)        0x2330     32     hard     yes     yes     yes
   Panther Point (PCH)   0x1e22     32     hard     yes     yes     yes
   Lynx Point (PCH)      0x8c22     32     hard     yes     yes     yes
+  Lynx Point-LP (PCH)   0x9c22     32     hard     yes     yes     yes
 
   Features supported by this driver:
   Software PEC                     no
@@ -155,6 +156,7 @@
 #define PCI_DEVICE_ID_INTEL_DH89XXCC_SMBUS	0x2330
 #define PCI_DEVICE_ID_INTEL_5_3400_SERIES_SMBUS	0x3b30
 #define PCI_DEVICE_ID_INTEL_LYNXPOINT_SMBUS	0x8c22
+#define PCI_DEVICE_ID_INTEL_LYNXPOINT_LP_SMBUS	0x9c22
 
 struct i801_priv {
 	struct i2c_adapter adapter;
@@ -771,6 +773,7 @@
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_DH89XXCC_SMBUS) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_PANTHERPOINT_SMBUS) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_LYNXPOINT_SMBUS) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_LYNXPOINT_LP_SMBUS) },
 	{ 0, }
 };
 
diff --git a/drivers/i2c/busses/i2c-mxs.c b/drivers/i2c/busses/i2c-mxs.c
index 088c5c1..51f05b8 100644
--- a/drivers/i2c/busses/i2c-mxs.c
+++ b/drivers/i2c/busses/i2c-mxs.c
@@ -365,10 +365,6 @@
 	struct device_node *node = dev->of_node;
 	int ret;
 
-	if (!node)
-		return -EINVAL;
-
-	i2c->speed = &mxs_i2c_95kHz_config;
 	ret = of_property_read_u32(node, "clock-frequency", &speed);
 	if (ret)
 		dev_warn(dev, "No I2C speed selected, using 100kHz\n");
@@ -419,10 +415,13 @@
 		return err;
 
 	i2c->dev = dev;
+	i2c->speed = &mxs_i2c_95kHz_config;
 
-	err = mxs_i2c_get_ofdata(i2c);
-	if (err)
-		return err;
+	if (dev->of_node) {
+		err = mxs_i2c_get_ofdata(i2c);
+		if (err)
+			return err;
+	}
 
 	platform_set_drvdata(pdev, i2c);
 
diff --git a/drivers/i2c/busses/i2c-pnx.c b/drivers/i2c/busses/i2c-pnx.c
index 5d54416..8488bdd 100644
--- a/drivers/i2c/busses/i2c-pnx.c
+++ b/drivers/i2c/busses/i2c-pnx.c
@@ -48,8 +48,9 @@
 	mcntrl_afie = 0x00000002,
 	mcntrl_naie = 0x00000004,
 	mcntrl_drmie = 0x00000008,
-	mcntrl_daie = 0x00000020,
-	mcntrl_rffie = 0x00000040,
+	mcntrl_drsie = 0x00000010,
+	mcntrl_rffie = 0x00000020,
+	mcntrl_daie = 0x00000040,
 	mcntrl_tffie = 0x00000080,
 	mcntrl_reset = 0x00000100,
 	mcntrl_cdbmode = 0x00000400,
@@ -290,31 +291,37 @@
 	 * or we didn't 'ask' for it yet.
 	 */
 	if (ioread32(I2C_REG_STS(alg_data)) & mstatus_rfe) {
-		dev_dbg(&alg_data->adapter.dev,
-			"%s(): Write dummy data to fill Rx-fifo...\n",
-			__func__);
+		/* 'Asking' is done asynchronously, e.g. dummy TX of several
+		 * bytes is done before the first actual RX arrives in FIFO.
+		 * Therefore, ordered bytes (via TX) are counted separately.
+		 */
+		if (alg_data->mif.order) {
+			dev_dbg(&alg_data->adapter.dev,
+				"%s(): Write dummy data to fill Rx-fifo...\n",
+				__func__);
 
-		if (alg_data->mif.len == 1) {
-			/* Last byte, do not acknowledge next rcv. */
-			val |= stop_bit;
+			if (alg_data->mif.order == 1) {
+				/* Last byte, do not acknowledge next rcv. */
+				val |= stop_bit;
+
+				/*
+				 * Enable interrupt RFDAIE (data in Rx fifo),
+				 * and disable DRMIE (need data for Tx)
+				 */
+				ctl = ioread32(I2C_REG_CTL(alg_data));
+				ctl |= mcntrl_rffie | mcntrl_daie;
+				ctl &= ~mcntrl_drmie;
+				iowrite32(ctl, I2C_REG_CTL(alg_data));
+			}
 
 			/*
-			 * Enable interrupt RFDAIE (data in Rx fifo),
-			 * and disable DRMIE (need data for Tx)
+			 * Now we'll 'ask' for data:
+			 * For each byte we want to receive, we must
+			 * write a (dummy) byte to the Tx-FIFO.
 			 */
-			ctl = ioread32(I2C_REG_CTL(alg_data));
-			ctl |= mcntrl_rffie | mcntrl_daie;
-			ctl &= ~mcntrl_drmie;
-			iowrite32(ctl, I2C_REG_CTL(alg_data));
+			iowrite32(val, I2C_REG_TX(alg_data));
+			alg_data->mif.order--;
 		}
-
-		/*
-		 * Now we'll 'ask' for data:
-		 * For each byte we want to receive, we must
-		 * write a (dummy) byte to the Tx-FIFO.
-		 */
-		iowrite32(val, I2C_REG_TX(alg_data));
-
 		return 0;
 	}
 
@@ -514,6 +521,7 @@
 
 		alg_data->mif.buf = pmsg->buf;
 		alg_data->mif.len = pmsg->len;
+		alg_data->mif.order = pmsg->len;
 		alg_data->mif.mode = (pmsg->flags & I2C_M_RD) ?
 			I2C_SMBUS_READ : I2C_SMBUS_WRITE;
 		alg_data->mif.ret = 0;
@@ -566,6 +574,7 @@
 	/* Cleanup to be sure... */
 	alg_data->mif.buf = NULL;
 	alg_data->mif.len = 0;
+	alg_data->mif.order = 0;
 
 	dev_dbg(&alg_data->adapter.dev, "%s(): exiting, stat = %x\n",
 		__func__, ioread32(I2C_REG_STS(alg_data)));
diff --git a/drivers/i2c/i2c-core.c b/drivers/i2c/i2c-core.c
index 2efa56c..2091ae8f 100644
--- a/drivers/i2c/i2c-core.c
+++ b/drivers/i2c/i2c-core.c
@@ -637,6 +637,22 @@
 }
 
 /*
+ * This function is only needed for mutex_lock_nested, so it is never
+ * called unless locking correctness checking is enabled. Thus we
+ * make it inline to avoid a compiler warning. That's what gcc ends up
+ * doing anyway.
+ */
+static inline unsigned int i2c_adapter_depth(struct i2c_adapter *adapter)
+{
+	unsigned int depth = 0;
+
+	while ((adapter = i2c_parent_is_i2c_adapter(adapter)))
+		depth++;
+
+	return depth;
+}
+
+/*
  * Let users instantiate I2C devices through sysfs. This can be used when
  * platform initialization code doesn't contain the proper data for
  * whatever reason. Also useful for drivers that do device detection and
@@ -726,7 +742,8 @@
 
 	/* Make sure the device was added through sysfs */
 	res = -ENOENT;
-	mutex_lock(&adap->userspace_clients_lock);
+	mutex_lock_nested(&adap->userspace_clients_lock,
+			  i2c_adapter_depth(adap));
 	list_for_each_entry_safe(client, next, &adap->userspace_clients,
 				 detected) {
 		if (client->addr == addr) {
@@ -1073,7 +1090,8 @@
 		return res;
 
 	/* Remove devices instantiated from sysfs */
-	mutex_lock(&adap->userspace_clients_lock);
+	mutex_lock_nested(&adap->userspace_clients_lock,
+			  i2c_adapter_depth(adap));
 	list_for_each_entry_safe(client, next, &adap->userspace_clients,
 				 detected) {
 		dev_dbg(&adap->dev, "Removing %s at 0x%x\n", client->name,
diff --git a/drivers/iio/adc/at91_adc.c b/drivers/iio/adc/at91_adc.c
index f61780a..3bd5540 100644
--- a/drivers/iio/adc/at91_adc.c
+++ b/drivers/iio/adc/at91_adc.c
@@ -617,7 +617,7 @@
 	st->adc_clk = clk_get(&pdev->dev, "adc_op_clk");
 	if (IS_ERR(st->adc_clk)) {
 		dev_err(&pdev->dev, "Failed to get the ADC clock.\n");
-		ret = PTR_ERR(st->clk);
+		ret = PTR_ERR(st->adc_clk);
 		goto error_disable_clk;
 	}
 
diff --git a/drivers/input/keyboard/imx_keypad.c b/drivers/input/keyboard/imx_keypad.c
index ff4c0a8..ce68e36 100644
--- a/drivers/input/keyboard/imx_keypad.c
+++ b/drivers/input/keyboard/imx_keypad.c
@@ -358,6 +358,7 @@
 	/* Inhibit KDI and KRI interrupts. */
 	reg_val = readw(keypad->mmio_base + KPSR);
 	reg_val &= ~(KBD_STAT_KRIE | KBD_STAT_KDIE);
+	reg_val |= KBD_STAT_KPKR | KBD_STAT_KPKD;
 	writew(reg_val, keypad->mmio_base + KPSR);
 
 	/* Colums as open drain and disable all rows */
@@ -515,7 +516,9 @@
 	input_set_drvdata(input_dev, keypad);
 
 	/* Ensure that the keypad will stay dormant until opened */
+	clk_enable(keypad->clk);
 	imx_keypad_inhibit(keypad);
+	clk_disable(keypad->clk);
 
 	error = request_irq(irq, imx_keypad_irq_handler, 0,
 			    pdev->name, keypad);
diff --git a/drivers/input/serio/i8042-x86ia64io.h b/drivers/input/serio/i8042-x86ia64io.h
index 5ec774d..6918773 100644
--- a/drivers/input/serio/i8042-x86ia64io.h
+++ b/drivers/input/serio/i8042-x86ia64io.h
@@ -177,6 +177,20 @@
 		},
 	},
 	{
+		/* Gigabyte T1005 - defines wrong chassis type ("Other") */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "GIGABYTE"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "T1005"),
+		},
+	},
+	{
+		/* Gigabyte T1005M/P - defines wrong chassis type ("Other") */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "GIGABYTE"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "T1005M/P"),
+		},
+	},
+	{
 		.matches = {
 			DMI_MATCH(DMI_SYS_VENDOR, "Hewlett-Packard"),
 			DMI_MATCH(DMI_PRODUCT_NAME, "HP Pavilion dv9700"),
diff --git a/drivers/input/tablet/wacom_wac.c b/drivers/input/tablet/wacom_wac.c
index 0020419..532d067 100644
--- a/drivers/input/tablet/wacom_wac.c
+++ b/drivers/input/tablet/wacom_wac.c
@@ -1848,7 +1848,10 @@
 	{ "Wacom Intuos5 M", WACOM_PKGLEN_INTUOS,  44704, 27940, 2047,
 	  63, INTUOS5, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES };
 static const struct wacom_features wacom_features_0xF4 =
-	{ "Wacom Cintiq 24HD",    WACOM_PKGLEN_INTUOS,   104480, 65600, 2047,
+	{ "Wacom Cintiq 24HD",       WACOM_PKGLEN_INTUOS,   104480, 65600, 2047,
+	  63, WACOM_24HD, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES };
+static const struct wacom_features wacom_features_0xF8 =
+	{ "Wacom Cintiq 24HD touch", WACOM_PKGLEN_INTUOS,   104480, 65600, 2047,
 	  63, WACOM_24HD, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES };
 static const struct wacom_features wacom_features_0x3F =
 	{ "Wacom Cintiq 21UX",    WACOM_PKGLEN_INTUOS,    87200, 65600, 1023,
@@ -2091,6 +2094,7 @@
 	{ USB_DEVICE_WACOM(0xEF) },
 	{ USB_DEVICE_WACOM(0x47) },
 	{ USB_DEVICE_WACOM(0xF4) },
+	{ USB_DEVICE_WACOM(0xF8) },
 	{ USB_DEVICE_WACOM(0xFA) },
 	{ USB_DEVICE_LENOVO(0x6004) },
 	{ }
diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
index 9afc777..b06a5e3 100644
--- a/drivers/input/touchscreen/edt-ft5x06.c
+++ b/drivers/input/touchscreen/edt-ft5x06.c
@@ -602,6 +602,7 @@
 {
 	if (tsdata->debug_dir)
 		debugfs_remove_recursive(tsdata->debug_dir);
+	kfree(tsdata->raw_buffer);
 }
 
 #else
@@ -843,7 +844,6 @@
 	if (gpio_is_valid(pdata->reset_pin))
 		gpio_free(pdata->reset_pin);
 
-	kfree(tsdata->raw_buffer);
 	kfree(tsdata);
 
 	return 0;
diff --git a/drivers/mmc/card/block.c b/drivers/mmc/card/block.c
index f1c84de..172a768 100644
--- a/drivers/mmc/card/block.c
+++ b/drivers/mmc/card/block.c
@@ -1411,7 +1411,8 @@
 		/* complete ongoing async transfer before issuing discard */
 		if (card->host->areq)
 			mmc_blk_issue_rw_rq(mq, NULL);
-		if (req->cmd_flags & REQ_SECURE)
+		if (req->cmd_flags & REQ_SECURE &&
+			!(card->quirks & MMC_QUIRK_SEC_ERASE_TRIM_BROKEN))
 			ret = mmc_blk_issue_secdiscard_rq(mq, req);
 		else
 			ret = mmc_blk_issue_discard_rq(mq, req);
@@ -1716,6 +1717,7 @@
 #define CID_MANFID_SANDISK	0x2
 #define CID_MANFID_TOSHIBA	0x11
 #define CID_MANFID_MICRON	0x13
+#define CID_MANFID_SAMSUNG	0x15
 
 static const struct mmc_fixup blk_fixups[] =
 {
@@ -1752,6 +1754,28 @@
 	MMC_FIXUP(CID_NAME_ANY, CID_MANFID_MICRON, 0x200, add_quirk_mmc,
 		  MMC_QUIRK_LONG_READ_TIME),
 
+	/*
+	 * On these Samsung MoviNAND parts, performing secure erase or
+	 * secure trim can result in unrecoverable corruption due to a
+	 * firmware bug.
+	 */
+	MMC_FIXUP("M8G2FA", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc,
+		  MMC_QUIRK_SEC_ERASE_TRIM_BROKEN),
+	MMC_FIXUP("MAG4FA", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc,
+		  MMC_QUIRK_SEC_ERASE_TRIM_BROKEN),
+	MMC_FIXUP("MBG8FA", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc,
+		  MMC_QUIRK_SEC_ERASE_TRIM_BROKEN),
+	MMC_FIXUP("MCGAFA", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc,
+		  MMC_QUIRK_SEC_ERASE_TRIM_BROKEN),
+	MMC_FIXUP("VAL00M", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc,
+		  MMC_QUIRK_SEC_ERASE_TRIM_BROKEN),
+	MMC_FIXUP("VYL00M", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc,
+		  MMC_QUIRK_SEC_ERASE_TRIM_BROKEN),
+	MMC_FIXUP("KYL00M", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc,
+		  MMC_QUIRK_SEC_ERASE_TRIM_BROKEN),
+	MMC_FIXUP("VZL00M", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc,
+		  MMC_QUIRK_SEC_ERASE_TRIM_BROKEN),
+
 	END_FIXUP
 };
 
diff --git a/drivers/mmc/host/atmel-mci.c b/drivers/mmc/host/atmel-mci.c
index 322412c..a53c7c4 100644
--- a/drivers/mmc/host/atmel-mci.c
+++ b/drivers/mmc/host/atmel-mci.c
@@ -81,6 +81,7 @@
 	bool	has_bad_data_ordering;
 	bool	need_reset_after_xfer;
 	bool	need_blksz_mul_4;
+	bool	need_notbusy_for_read_ops;
 };
 
 struct atmel_mci_dma {
@@ -1625,7 +1626,8 @@
 				__func__);
 			atmci_set_completed(host, EVENT_XFER_COMPLETE);
 
-			if (host->data->flags & MMC_DATA_WRITE) {
+			if (host->caps.need_notbusy_for_read_ops ||
+			   (host->data->flags & MMC_DATA_WRITE)) {
 				atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
 				state = STATE_WAITING_NOTBUSY;
 			} else if (host->mrq->stop) {
@@ -2218,6 +2220,7 @@
 	host->caps.has_bad_data_ordering = 1;
 	host->caps.need_reset_after_xfer = 1;
 	host->caps.need_blksz_mul_4 = 1;
+	host->caps.need_notbusy_for_read_ops = 0;
 
 	/* keep only major version number */
 	switch (version & 0xf00) {
@@ -2238,6 +2241,7 @@
 	case 0x200:
 		host->caps.has_rwproof = 1;
 		host->caps.need_blksz_mul_4 = 0;
+		host->caps.need_notbusy_for_read_ops = 1;
 	case 0x100:
 		host->caps.has_bad_data_ordering = 0;
 		host->caps.need_reset_after_xfer = 0;
diff --git a/drivers/mmc/host/bfin_sdh.c b/drivers/mmc/host/bfin_sdh.c
index 0366617..a17dd73 100644
--- a/drivers/mmc/host/bfin_sdh.c
+++ b/drivers/mmc/host/bfin_sdh.c
@@ -49,13 +49,6 @@
 #define bfin_write_SDH_CFG		bfin_write_RSI_CFG
 #endif
 
-struct dma_desc_array {
-	unsigned long	start_addr;
-	unsigned short	cfg;
-	unsigned short	x_count;
-	short		x_modify;
-} __packed;
-
 struct sdh_host {
 	struct mmc_host		*mmc;
 	spinlock_t		lock;
diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
index 72dc3cd..af40d22 100644
--- a/drivers/mmc/host/dw_mmc.c
+++ b/drivers/mmc/host/dw_mmc.c
@@ -627,6 +627,7 @@
 {
 	struct dw_mci *host = slot->host;
 	u32 div;
+	u32 clk_en_a;
 
 	if (slot->clock != host->current_speed) {
 		div = host->bus_hz / slot->clock;
@@ -659,9 +660,11 @@
 		mci_send_cmd(slot,
 			     SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT, 0);
 
-		/* enable clock */
-		mci_writel(host, CLKENA, ((SDMMC_CLKEN_ENABLE |
-			   SDMMC_CLKEN_LOW_PWR) << slot->id));
+		/* enable clock; only low power if no SDIO */
+		clk_en_a = SDMMC_CLKEN_ENABLE << slot->id;
+		if (!(mci_readl(host, INTMASK) & SDMMC_INT_SDIO(slot->id)))
+			clk_en_a |= SDMMC_CLKEN_LOW_PWR << slot->id;
+		mci_writel(host, CLKENA, clk_en_a);
 
 		/* inform CIU */
 		mci_send_cmd(slot,
@@ -862,6 +865,30 @@
 	return present;
 }
 
+/*
+ * Disable lower power mode.
+ *
+ * Low power mode will stop the card clock when idle.  According to the
+ * description of the CLKENA register we should disable low power mode
+ * for SDIO cards if we need SDIO interrupts to work.
+ *
+ * This function is fast if low power mode is already disabled.
+ */
+static void dw_mci_disable_low_power(struct dw_mci_slot *slot)
+{
+	struct dw_mci *host = slot->host;
+	u32 clk_en_a;
+	const u32 clken_low_pwr = SDMMC_CLKEN_LOW_PWR << slot->id;
+
+	clk_en_a = mci_readl(host, CLKENA);
+
+	if (clk_en_a & clken_low_pwr) {
+		mci_writel(host, CLKENA, clk_en_a & ~clken_low_pwr);
+		mci_send_cmd(slot, SDMMC_CMD_UPD_CLK |
+			     SDMMC_CMD_PRV_DAT_WAIT, 0);
+	}
+}
+
 static void dw_mci_enable_sdio_irq(struct mmc_host *mmc, int enb)
 {
 	struct dw_mci_slot *slot = mmc_priv(mmc);
@@ -871,6 +898,14 @@
 	/* Enable/disable Slot Specific SDIO interrupt */
 	int_mask = mci_readl(host, INTMASK);
 	if (enb) {
+		/*
+		 * Turn off low power mode if it was enabled.  This is a bit of
+		 * a heavy operation and we disable / enable IRQs a lot, so
+		 * we'll leave low power mode disabled and it will get
+		 * re-enabled again in dw_mci_setup_bus().
+		 */
+		dw_mci_disable_low_power(slot);
+
 		mci_writel(host, INTMASK,
 			   (int_mask | SDMMC_INT_SDIO(slot->id)));
 	} else {
@@ -1429,22 +1464,10 @@
 			nbytes += len;
 			remain -= len;
 		} while (remain);
-		sg_miter->consumed = offset;
 
+		sg_miter->consumed = offset;
 		status = mci_readl(host, MINTSTS);
 		mci_writel(host, RINTSTS, SDMMC_INT_RXDR);
-		if (status & DW_MCI_DATA_ERROR_FLAGS) {
-			host->data_status = status;
-			data->bytes_xfered += nbytes;
-			sg_miter_stop(sg_miter);
-			host->sg = NULL;
-			smp_wmb();
-
-			set_bit(EVENT_DATA_ERROR, &host->pending_events);
-
-			tasklet_schedule(&host->tasklet);
-			return;
-		}
 	} while (status & SDMMC_INT_RXDR); /*if the RXDR is ready read again*/
 	data->bytes_xfered += nbytes;
 
@@ -1497,23 +1520,10 @@
 			nbytes += len;
 			remain -= len;
 		} while (remain);
-		sg_miter->consumed = offset;
 
+		sg_miter->consumed = offset;
 		status = mci_readl(host, MINTSTS);
 		mci_writel(host, RINTSTS, SDMMC_INT_TXDR);
-		if (status & DW_MCI_DATA_ERROR_FLAGS) {
-			host->data_status = status;
-			data->bytes_xfered += nbytes;
-			sg_miter_stop(sg_miter);
-			host->sg = NULL;
-
-			smp_wmb();
-
-			set_bit(EVENT_DATA_ERROR, &host->pending_events);
-
-			tasklet_schedule(&host->tasklet);
-			return;
-		}
 	} while (status & SDMMC_INT_TXDR); /* if TXDR write again */
 	data->bytes_xfered += nbytes;
 
@@ -1547,12 +1557,11 @@
 static irqreturn_t dw_mci_interrupt(int irq, void *dev_id)
 {
 	struct dw_mci *host = dev_id;
-	u32 status, pending;
+	u32 pending;
 	unsigned int pass_count = 0;
 	int i;
 
 	do {
-		status = mci_readl(host, RINTSTS);
 		pending = mci_readl(host, MINTSTS); /* read-only mask reg */
 
 		/*
@@ -1570,7 +1579,7 @@
 
 		if (pending & DW_MCI_CMD_ERROR_FLAGS) {
 			mci_writel(host, RINTSTS, DW_MCI_CMD_ERROR_FLAGS);
-			host->cmd_status = status;
+			host->cmd_status = pending;
 			smp_wmb();
 			set_bit(EVENT_CMD_COMPLETE, &host->pending_events);
 		}
@@ -1578,18 +1587,16 @@
 		if (pending & DW_MCI_DATA_ERROR_FLAGS) {
 			/* if there is an error report DATA_ERROR */
 			mci_writel(host, RINTSTS, DW_MCI_DATA_ERROR_FLAGS);
-			host->data_status = status;
+			host->data_status = pending;
 			smp_wmb();
 			set_bit(EVENT_DATA_ERROR, &host->pending_events);
-			if (!(pending & (SDMMC_INT_DTO | SDMMC_INT_DCRC |
-					 SDMMC_INT_SBE | SDMMC_INT_EBE)))
-				tasklet_schedule(&host->tasklet);
+			tasklet_schedule(&host->tasklet);
 		}
 
 		if (pending & SDMMC_INT_DATA_OVER) {
 			mci_writel(host, RINTSTS, SDMMC_INT_DATA_OVER);
 			if (!host->data_status)
-				host->data_status = status;
+				host->data_status = pending;
 			smp_wmb();
 			if (host->dir_status == DW_MCI_RECV_STATUS) {
 				if (host->sg != NULL)
@@ -1613,7 +1620,7 @@
 
 		if (pending & SDMMC_INT_CMD_DONE) {
 			mci_writel(host, RINTSTS, SDMMC_INT_CMD_DONE);
-			dw_mci_cmd_interrupt(host, status);
+			dw_mci_cmd_interrupt(host, pending);
 		}
 
 		if (pending & SDMMC_INT_CD) {
diff --git a/drivers/mmc/host/mxs-mmc.c b/drivers/mmc/host/mxs-mmc.c
index a51f930..ad3fcea 100644
--- a/drivers/mmc/host/mxs-mmc.c
+++ b/drivers/mmc/host/mxs-mmc.c
@@ -285,11 +285,11 @@
 	writel(stat & MXS_MMC_IRQ_BITS,
 	       host->base + HW_SSP_CTRL1(host) + STMP_OFFSET_REG_CLR);
 
+	spin_unlock(&host->lock);
+
 	if ((stat & BM_SSP_CTRL1_SDIO_IRQ) && (stat & BM_SSP_CTRL1_SDIO_IRQ_EN))
 		mmc_signal_sdio_irq(host->mmc);
 
-	spin_unlock(&host->lock);
-
 	if (stat & BM_SSP_CTRL1_RESP_TIMEOUT_IRQ)
 		cmd->error = -ETIMEDOUT;
 	else if (stat & BM_SSP_CTRL1_RESP_ERR_IRQ)
@@ -644,11 +644,6 @@
 		       host->base + HW_SSP_CTRL0 + STMP_OFFSET_REG_SET);
 		writel(BM_SSP_CTRL1_SDIO_IRQ_EN,
 		       host->base + HW_SSP_CTRL1(host) + STMP_OFFSET_REG_SET);
-
-		if (readl(host->base + HW_SSP_STATUS(host)) &
-				BM_SSP_STATUS_SDIO_IRQ)
-			mmc_signal_sdio_irq(host->mmc);
-
 	} else {
 		writel(BM_SSP_CTRL0_SDIO_IRQ_CHECK,
 		       host->base + HW_SSP_CTRL0 + STMP_OFFSET_REG_CLR);
@@ -657,6 +652,11 @@
 	}
 
 	spin_unlock_irqrestore(&host->lock, flags);
+
+	if (enable && readl(host->base + HW_SSP_STATUS(host)) &
+			BM_SSP_STATUS_SDIO_IRQ)
+		mmc_signal_sdio_irq(host->mmc);
+
 }
 
 static const struct mmc_host_ops mxs_mmc_ops = {
diff --git a/drivers/mmc/host/omap.c b/drivers/mmc/host/omap.c
index 50e08f0..a5999a7 100644
--- a/drivers/mmc/host/omap.c
+++ b/drivers/mmc/host/omap.c
@@ -668,7 +668,7 @@
 static void
 mmc_omap_xfer_data(struct mmc_omap_host *host, int write)
 {
-	int n;
+	int n, nwords;
 
 	if (host->buffer_bytes_left == 0) {
 		host->sg_idx++;
@@ -678,15 +678,23 @@
 	n = 64;
 	if (n > host->buffer_bytes_left)
 		n = host->buffer_bytes_left;
+
+	nwords = n / 2;
+	nwords += n & 1; /* handle odd number of bytes to transfer */
+
 	host->buffer_bytes_left -= n;
 	host->total_bytes_left -= n;
 	host->data->bytes_xfered += n;
 
 	if (write) {
-		__raw_writesw(host->virt_base + OMAP_MMC_REG(host, DATA), host->buffer, n);
+		__raw_writesw(host->virt_base + OMAP_MMC_REG(host, DATA),
+			      host->buffer, nwords);
 	} else {
-		__raw_readsw(host->virt_base + OMAP_MMC_REG(host, DATA), host->buffer, n);
+		__raw_readsw(host->virt_base + OMAP_MMC_REG(host, DATA),
+			     host->buffer, nwords);
 	}
+
+	host->buffer += nwords;
 }
 
 static inline void mmc_omap_report_irq(u16 status)
diff --git a/drivers/mmc/host/sdhci-esdhc.h b/drivers/mmc/host/sdhci-esdhc.h
index b97b2f5..d25f9ab 100644
--- a/drivers/mmc/host/sdhci-esdhc.h
+++ b/drivers/mmc/host/sdhci-esdhc.h
@@ -48,14 +48,14 @@
 	int div = 1;
 	u32 temp;
 
+	if (clock == 0)
+		goto out;
+
 	temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL);
 	temp &= ~(ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN
 		| ESDHC_CLOCK_MASK);
 	sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL);
 
-	if (clock == 0)
-		goto out;
-
 	while (host->max_clk / pre_div / 16 > clock && pre_div < 256)
 		pre_div *= 2;
 
diff --git a/drivers/mtd/ubi/vtbl.c b/drivers/mtd/ubi/vtbl.c
index 437bc19..568307c 100644
--- a/drivers/mtd/ubi/vtbl.c
+++ b/drivers/mtd/ubi/vtbl.c
@@ -340,7 +340,7 @@
 	 * of this LEB as it will be deleted and freed in 'ubi_add_to_av()'.
 	 */
 	err = ubi_add_to_av(ubi, ai, new_aeb->pnum, new_aeb->ec, vid_hdr, 0);
-	kfree(new_aeb);
+	kmem_cache_free(ai->aeb_slab_cache, new_aeb);
 	ubi_free_vid_hdr(ubi, vid_hdr);
 	return err;
 
@@ -353,7 +353,7 @@
 		list_add(&new_aeb->u.list, &ai->erase);
 		goto retry;
 	}
-	kfree(new_aeb);
+	kmem_cache_free(ai->aeb_slab_cache, new_aeb);
 out_free:
 	ubi_free_vid_hdr(ubi, vid_hdr);
 	return err;
diff --git a/drivers/pci/pci-driver.c b/drivers/pci/pci-driver.c
index 5270f1a..d6fd6b6 100644
--- a/drivers/pci/pci-driver.c
+++ b/drivers/pci/pci-driver.c
@@ -280,8 +280,12 @@
 {
 	struct drv_dev_and_id *ddi = _ddi;
 	struct device *dev = &ddi->dev->dev;
+	struct device *parent = dev->parent;
 	int rc;
 
+	/* The parent bridge must be in active state when probing */
+	if (parent)
+		pm_runtime_get_sync(parent);
 	/* Unbound PCI devices are always set to disabled and suspended.
 	 * During probe, the device is set to enabled and active and the
 	 * usage count is incremented.  If the driver supports runtime PM,
@@ -298,6 +302,8 @@
 		pm_runtime_set_suspended(dev);
 		pm_runtime_put_noidle(dev);
 	}
+	if (parent)
+		pm_runtime_put(parent);
 	return rc;
 }
 
diff --git a/drivers/pci/pci-sysfs.c b/drivers/pci/pci-sysfs.c
index 6869009..02d107b 100644
--- a/drivers/pci/pci-sysfs.c
+++ b/drivers/pci/pci-sysfs.c
@@ -458,6 +458,40 @@
 }
 struct device_attribute vga_attr = __ATTR_RO(boot_vga);
 
+static void
+pci_config_pm_runtime_get(struct pci_dev *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device *parent = dev->parent;
+
+	if (parent)
+		pm_runtime_get_sync(parent);
+	pm_runtime_get_noresume(dev);
+	/*
+	 * pdev->current_state is set to PCI_D3cold during suspending,
+	 * so wait until suspending completes
+	 */
+	pm_runtime_barrier(dev);
+	/*
+	 * Only need to resume devices in D3cold, because config
+	 * registers are still accessible for devices suspended but
+	 * not in D3cold.
+	 */
+	if (pdev->current_state == PCI_D3cold)
+		pm_runtime_resume(dev);
+}
+
+static void
+pci_config_pm_runtime_put(struct pci_dev *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device *parent = dev->parent;
+
+	pm_runtime_put(dev);
+	if (parent)
+		pm_runtime_put_sync(parent);
+}
+
 static ssize_t
 pci_read_config(struct file *filp, struct kobject *kobj,
 		struct bin_attribute *bin_attr,
@@ -484,6 +518,8 @@
 		size = count;
 	}
 
+	pci_config_pm_runtime_get(dev);
+
 	if ((off & 1) && size) {
 		u8 val;
 		pci_user_read_config_byte(dev, off, &val);
@@ -529,6 +565,8 @@
 		--size;
 	}
 
+	pci_config_pm_runtime_put(dev);
+
 	return count;
 }
 
@@ -549,6 +587,8 @@
 		count = size;
 	}
 	
+	pci_config_pm_runtime_get(dev);
+
 	if ((off & 1) && size) {
 		pci_user_write_config_byte(dev, off, data[off - init_off]);
 		off++;
@@ -587,6 +627,8 @@
 		--size;
 	}
 
+	pci_config_pm_runtime_put(dev);
+
 	return count;
 }
 
diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c
index f3ea977..ab4bf5a 100644
--- a/drivers/pci/pci.c
+++ b/drivers/pci/pci.c
@@ -1941,6 +1941,7 @@
 	dev->pm_cap = pm;
 	dev->d3_delay = PCI_PM_D3_WAIT;
 	dev->d3cold_delay = PCI_PM_D3COLD_WAIT;
+	dev->d3cold_allowed = true;
 
 	dev->d1_support = false;
 	dev->d2_support = false;
diff --git a/drivers/pci/pcie/portdrv_pci.c b/drivers/pci/pcie/portdrv_pci.c
index 3a7eefc..e76b447 100644
--- a/drivers/pci/pcie/portdrv_pci.c
+++ b/drivers/pci/pcie/portdrv_pci.c
@@ -140,9 +140,17 @@
 {
 	return 0;
 }
+
+static int pcie_port_runtime_idle(struct device *dev)
+{
+	/* Delay for a short while to prevent too frequent suspend/resume */
+	pm_schedule_suspend(dev, 10);
+	return -EBUSY;
+}
 #else
 #define pcie_port_runtime_suspend	NULL
 #define pcie_port_runtime_resume	NULL
+#define pcie_port_runtime_idle		NULL
 #endif
 
 static const struct dev_pm_ops pcie_portdrv_pm_ops = {
@@ -155,6 +163,7 @@
 	.resume_noirq	= pcie_port_resume_noirq,
 	.runtime_suspend = pcie_port_runtime_suspend,
 	.runtime_resume = pcie_port_runtime_resume,
+	.runtime_idle	= pcie_port_runtime_idle,
 };
 
 #define PCIE_PORTDRV_PM_OPS	(&pcie_portdrv_pm_ops)
@@ -200,6 +209,11 @@
 		return status;
 
 	pci_save_state(dev);
+	/*
+	 * D3cold may not work properly on some PCIe port, so disable
+	 * it by default.
+	 */
+	dev->d3cold_allowed = false;
 	if (!pci_match_id(port_runtime_pm_black_list, dev))
 		pm_runtime_put_noidle(&dev->dev);
 
diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c
index 6c143b4..9f8a6b7 100644
--- a/drivers/pci/probe.c
+++ b/drivers/pci/probe.c
@@ -144,15 +144,13 @@
 	case PCI_BASE_ADDRESS_MEM_TYPE_32:
 		break;
 	case PCI_BASE_ADDRESS_MEM_TYPE_1M:
-		dev_info(&dev->dev, "1M mem BAR treated as 32-bit BAR\n");
+		/* 1M mem BAR treated as 32-bit BAR */
 		break;
 	case PCI_BASE_ADDRESS_MEM_TYPE_64:
 		flags |= IORESOURCE_MEM_64;
 		break;
 	default:
-		dev_warn(&dev->dev,
-			 "mem unknown type %x treated as 32-bit BAR\n",
-			 mem_type);
+		/* mem unknown type treated as 32-bit BAR */
 		break;
 	}
 	return flags;
@@ -173,9 +171,11 @@
 	u32 l, sz, mask;
 	u16 orig_cmd;
 	struct pci_bus_region region;
+	bool bar_too_big = false, bar_disabled = false;
 
 	mask = type ? PCI_ROM_ADDRESS_MASK : ~0;
 
+	/* No printks while decoding is disabled! */
 	if (!dev->mmio_always_on) {
 		pci_read_config_word(dev, PCI_COMMAND, &orig_cmd);
 		pci_write_config_word(dev, PCI_COMMAND,
@@ -240,8 +240,7 @@
 			goto fail;
 
 		if ((sizeof(resource_size_t) < 8) && (sz64 > 0x100000000ULL)) {
-			dev_err(&dev->dev, "reg %x: can't handle 64-bit BAR\n",
-				pos);
+			bar_too_big = true;
 			goto fail;
 		}
 
@@ -252,12 +251,11 @@
 			region.start = 0;
 			region.end = sz64;
 			pcibios_bus_to_resource(dev, res, &region);
+			bar_disabled = true;
 		} else {
 			region.start = l64;
 			region.end = l64 + sz64;
 			pcibios_bus_to_resource(dev, res, &region);
-			dev_printk(KERN_DEBUG, &dev->dev, "reg %x: %pR\n",
-				   pos, res);
 		}
 	} else {
 		sz = pci_size(l, sz, mask);
@@ -268,18 +266,23 @@
 		region.start = l;
 		region.end = l + sz;
 		pcibios_bus_to_resource(dev, res, &region);
-
-		dev_printk(KERN_DEBUG, &dev->dev, "reg %x: %pR\n", pos, res);
 	}
 
- out:
+	goto out;
+
+
+fail:
+	res->flags = 0;
+out:
 	if (!dev->mmio_always_on)
 		pci_write_config_word(dev, PCI_COMMAND, orig_cmd);
 
+	if (bar_too_big)
+		dev_err(&dev->dev, "reg %x: can't handle 64-bit BAR\n", pos);
+	if (res->flags && !bar_disabled)
+		dev_printk(KERN_DEBUG, &dev->dev, "reg %x: %pR\n", pos, res);
+
 	return (res->flags & IORESOURCE_MEM_64) ? 1 : 0;
- fail:
-	res->flags = 0;
-	goto out;
 }
 
 static void pci_read_bases(struct pci_dev *dev, unsigned int howmany, int rom)
diff --git a/drivers/platform/x86/acer-wmi.c b/drivers/platform/x86/acer-wmi.c
index 3782e1c..934d861 100644
--- a/drivers/platform/x86/acer-wmi.c
+++ b/drivers/platform/x86/acer-wmi.c
@@ -2196,10 +2196,8 @@
 		interface->capability &= ~ACER_CAP_BRIGHTNESS;
 		pr_info("Brightness must be controlled by acpi video driver\n");
 	} else {
-#ifdef CONFIG_ACPI_VIDEO
 		pr_info("Disabling ACPI video driver\n");
 		acpi_video_unregister();
-#endif
 	}
 
 	if (wmi_has_guid(WMID_GUID3)) {
diff --git a/drivers/platform/x86/apple-gmux.c b/drivers/platform/x86/apple-gmux.c
index dfb1a92..db8f638 100644
--- a/drivers/platform/x86/apple-gmux.c
+++ b/drivers/platform/x86/apple-gmux.c
@@ -101,7 +101,7 @@
 
 	for (i = 0; i < 4; i++) {
 		tmpval = (val >> (i * 8)) & 0xff;
-		outb(tmpval, port + i);
+		outb(tmpval, gmux_data->iostart + port + i);
 	}
 }
 
@@ -142,8 +142,9 @@
 	u8 val;
 
 	mutex_lock(&gmux_data->index_lock);
-	outb((port & 0xff), gmux_data->iostart + GMUX_PORT_READ);
 	gmux_index_wait_ready(gmux_data);
+	outb((port & 0xff), gmux_data->iostart + GMUX_PORT_READ);
+	gmux_index_wait_complete(gmux_data);
 	val = inb(gmux_data->iostart + GMUX_PORT_VALUE);
 	mutex_unlock(&gmux_data->index_lock);
 
@@ -166,8 +167,9 @@
 	u32 val;
 
 	mutex_lock(&gmux_data->index_lock);
-	outb((port & 0xff), gmux_data->iostart + GMUX_PORT_READ);
 	gmux_index_wait_ready(gmux_data);
+	outb((port & 0xff), gmux_data->iostart + GMUX_PORT_READ);
+	gmux_index_wait_complete(gmux_data);
 	val = inl(gmux_data->iostart + GMUX_PORT_VALUE);
 	mutex_unlock(&gmux_data->index_lock);
 
@@ -461,18 +463,22 @@
 	ver_release = gmux_read8(gmux_data, GMUX_PORT_VERSION_RELEASE);
 	if (ver_major == 0xff && ver_minor == 0xff && ver_release == 0xff) {
 		if (gmux_is_indexed(gmux_data)) {
+			u32 version;
 			mutex_init(&gmux_data->index_lock);
 			gmux_data->indexed = true;
+			version = gmux_read32(gmux_data,
+				GMUX_PORT_VERSION_MAJOR);
+			ver_major = (version >> 24) & 0xff;
+			ver_minor = (version >> 16) & 0xff;
+			ver_release = (version >> 8) & 0xff;
 		} else {
 			pr_info("gmux device not present\n");
 			ret = -ENODEV;
 			goto err_release;
 		}
-		pr_info("Found indexed gmux\n");
-	} else {
-		pr_info("Found gmux version %d.%d.%d\n", ver_major, ver_minor,
-			ver_release);
 	}
+	pr_info("Found gmux version %d.%d.%d [%s]\n", ver_major, ver_minor,
+		ver_release, (gmux_data->indexed ? "indexed" : "classic"));
 
 	memset(&props, 0, sizeof(props));
 	props.type = BACKLIGHT_PLATFORM;
@@ -505,9 +511,7 @@
 	 * Disable the other backlight choices.
 	 */
 	acpi_video_dmi_promote_vendor();
-#if defined (CONFIG_ACPI_VIDEO) || defined (CONFIG_ACPI_VIDEO_MODULE)
 	acpi_video_unregister();
-#endif
 	apple_bl_unregister();
 
 	gmux_data->power_state = VGA_SWITCHEROO_ON;
@@ -593,9 +597,7 @@
 	kfree(gmux_data);
 
 	acpi_video_dmi_demote_vendor();
-#if defined (CONFIG_ACPI_VIDEO) || defined (CONFIG_ACPI_VIDEO_MODULE)
 	acpi_video_register();
-#endif
 	apple_bl_register();
 }
 
diff --git a/drivers/platform/x86/asus-laptop.c b/drivers/platform/x86/asus-laptop.c
index e38f91b..4b568df 100644
--- a/drivers/platform/x86/asus-laptop.c
+++ b/drivers/platform/x86/asus-laptop.c
@@ -85,7 +85,7 @@
 static char *bled_type = "unknown";
 
 module_param(wled_type, charp, 0444);
-MODULE_PARM_DESC(wlan_status, "Set the wled type on boot "
+MODULE_PARM_DESC(wled_type, "Set the wled type on boot "
 		 "(unknown, led or rfkill). "
 		 "default is unknown");
 
@@ -863,9 +863,9 @@
 	 * The significance of others is yet to be found.
 	 * If we don't find the method, we assume the device are present.
 	 */
-	rv = acpi_evaluate_integer(asus->handle, "HRWS", NULL, &temp);
+	rv = acpi_evaluate_integer(asus->handle, "HWRS", NULL, &temp);
 	if (!ACPI_FAILURE(rv))
-		len += sprintf(page + len, "HRWS value         : %#x\n",
+		len += sprintf(page + len, "HWRS value         : %#x\n",
 			       (uint) temp);
 	/*
 	 * Another value for userspace: the ASYM method returns 0x02 for
@@ -1751,9 +1751,9 @@
 	 * The significance of others is yet to be found.
 	 */
 	status =
-	    acpi_evaluate_integer(asus->handle, "HRWS", NULL, &hwrs_result);
+	    acpi_evaluate_integer(asus->handle, "HWRS", NULL, &hwrs_result);
 	if (!ACPI_FAILURE(status))
-		pr_notice("  HRWS returned %x", (int)hwrs_result);
+		pr_notice("  HWRS returned %x", (int)hwrs_result);
 
 	if (!acpi_check_handle(asus->handle, METHOD_WL_STATUS, NULL))
 		asus->have_rsts = true;
diff --git a/drivers/platform/x86/asus-wmi.c b/drivers/platform/x86/asus-wmi.c
index 2eb9fe8..c0e9ff4 100644
--- a/drivers/platform/x86/asus-wmi.c
+++ b/drivers/platform/x86/asus-wmi.c
@@ -47,9 +47,7 @@
 #include <linux/thermal.h>
 #include <acpi/acpi_bus.h>
 #include <acpi/acpi_drivers.h>
-#ifdef CONFIG_ACPI_VIDEO
 #include <acpi/video.h>
-#endif
 
 #include "asus-wmi.h"
 
@@ -1704,10 +1702,8 @@
 	if (asus->driver->quirks->wmi_backlight_power)
 		acpi_video_dmi_promote_vendor();
 	if (!acpi_video_backlight_support()) {
-#ifdef CONFIG_ACPI_VIDEO
 		pr_info("Disabling ACPI video driver\n");
 		acpi_video_unregister();
-#endif
 		err = asus_wmi_backlight_init(asus);
 		if (err && err != -ENODEV)
 			goto fail_backlight;
diff --git a/drivers/platform/x86/eeepc-laptop.c b/drivers/platform/x86/eeepc-laptop.c
index dab91b4..5ca2641 100644
--- a/drivers/platform/x86/eeepc-laptop.c
+++ b/drivers/platform/x86/eeepc-laptop.c
@@ -610,12 +610,12 @@
 
 		if (!bus) {
 			pr_warn("Unable to find PCI bus 1?\n");
-			goto out_unlock;
+			goto out_put_dev;
 		}
 
 		if (pci_bus_read_config_dword(bus, 0, PCI_VENDOR_ID, &l)) {
 			pr_err("Unable to read PCI config space?\n");
-			goto out_unlock;
+			goto out_put_dev;
 		}
 
 		absent = (l == 0xffffffff);
@@ -627,7 +627,7 @@
 				absent ? "absent" : "present");
 			pr_warn("skipped wireless hotplug as probably "
 				"inappropriate for this model\n");
-			goto out_unlock;
+			goto out_put_dev;
 		}
 
 		if (!blocked) {
@@ -635,7 +635,7 @@
 			if (dev) {
 				/* Device already present */
 				pci_dev_put(dev);
-				goto out_unlock;
+				goto out_put_dev;
 			}
 			dev = pci_scan_single_device(bus, 0);
 			if (dev) {
@@ -650,6 +650,8 @@
 				pci_dev_put(dev);
 			}
 		}
+out_put_dev:
+		pci_dev_put(port);
 	}
 
 out_unlock:
diff --git a/drivers/platform/x86/samsung-laptop.c b/drivers/platform/x86/samsung-laptop.c
index c1ca7bc..dd90d15 100644
--- a/drivers/platform/x86/samsung-laptop.c
+++ b/drivers/platform/x86/samsung-laptop.c
@@ -26,9 +26,7 @@
 #include <linux/seq_file.h>
 #include <linux/debugfs.h>
 #include <linux/ctype.h>
-#ifdef CONFIG_ACPI_VIDEO
 #include <acpi/video.h>
-#endif
 
 /*
  * This driver is needed because a number of Samsung laptops do not hook
@@ -1558,9 +1556,7 @@
 		samsung->handle_backlight = false;
 	} else if (samsung->quirks->broken_acpi_video) {
 		pr_info("Disabling ACPI video driver\n");
-#ifdef CONFIG_ACPI_VIDEO
 		acpi_video_unregister();
-#endif
 	}
 #endif
 
diff --git a/drivers/platform/x86/thinkpad_acpi.c b/drivers/platform/x86/thinkpad_acpi.c
index 80e3779..52daaa8 100644
--- a/drivers/platform/x86/thinkpad_acpi.c
+++ b/drivers/platform/x86/thinkpad_acpi.c
@@ -545,7 +545,7 @@
  */
 
 static int acpi_evalf(acpi_handle handle,
-		      void *res, char *method, char *fmt, ...)
+		      int *res, char *method, char *fmt, ...)
 {
 	char *fmt0 = fmt;
 	struct acpi_object_list params;
@@ -606,7 +606,7 @@
 		success = (status == AE_OK &&
 			   out_obj.type == ACPI_TYPE_INTEGER);
 		if (success && res)
-			*(int *)res = out_obj.integer.value;
+			*res = out_obj.integer.value;
 		break;
 	case 'v':		/* void */
 		success = status == AE_OK;
@@ -7386,17 +7386,18 @@
 	 * Add TPACPI_FAN_RD_ACPI_FANS ? */
 
 	switch (fan_status_access_mode) {
-	case TPACPI_FAN_RD_ACPI_GFAN:
+	case TPACPI_FAN_RD_ACPI_GFAN: {
 		/* 570, 600e/x, 770e, 770x */
+		int res;
 
-		if (unlikely(!acpi_evalf(gfan_handle, &s, NULL, "d")))
+		if (unlikely(!acpi_evalf(gfan_handle, &res, NULL, "d")))
 			return -EIO;
 
 		if (likely(status))
-			*status = s & 0x07;
+			*status = res & 0x07;
 
 		break;
-
+	}
 	case TPACPI_FAN_RD_TPEC:
 		/* all except 570, 600e/x, 770e, 770x */
 		if (unlikely(!acpi_ec_read(fan_status_offset, &s)))
diff --git a/drivers/rtc/rtc-at91sam9.c b/drivers/rtc/rtc-at91sam9.c
index 8318689..1dd61f4 100644
--- a/drivers/rtc/rtc-at91sam9.c
+++ b/drivers/rtc/rtc-at91sam9.c
@@ -58,6 +58,7 @@
 	struct rtc_device	*rtcdev;
 	u32			imr;
 	void __iomem		*gpbr;
+	int 			irq;
 };
 
 #define rtt_readl(rtc, field) \
@@ -292,7 +293,7 @@
 {
 	struct resource	*r, *r_gpbr;
 	struct sam9_rtc	*rtc;
-	int		ret;
+	int		ret, irq;
 	u32		mr;
 
 	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
@@ -302,10 +303,18 @@
 		return -ENODEV;
 	}
 
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(&pdev->dev, "failed to get interrupt resource\n");
+		return irq;
+	}
+
 	rtc = kzalloc(sizeof *rtc, GFP_KERNEL);
 	if (!rtc)
 		return -ENOMEM;
 
+	rtc->irq = irq;
+
 	/* platform setup code should have handled this; sigh */
 	if (!device_can_wakeup(&pdev->dev))
 		device_init_wakeup(&pdev->dev, 1);
@@ -345,11 +354,10 @@
 	}
 
 	/* register irq handler after we know what name we'll use */
-	ret = request_irq(AT91_ID_SYS, at91_rtc_interrupt,
-				IRQF_SHARED,
+	ret = request_irq(rtc->irq, at91_rtc_interrupt, IRQF_SHARED,
 				dev_name(&rtc->rtcdev->dev), rtc);
 	if (ret) {
-		dev_dbg(&pdev->dev, "can't share IRQ %d?\n", AT91_ID_SYS);
+		dev_dbg(&pdev->dev, "can't share IRQ %d?\n", rtc->irq);
 		rtc_device_unregister(rtc->rtcdev);
 		goto fail_register;
 	}
@@ -386,7 +394,7 @@
 
 	/* disable all interrupts */
 	rtt_writel(rtc, MR, mr & ~(AT91_RTT_ALMIEN | AT91_RTT_RTTINCIEN));
-	free_irq(AT91_ID_SYS, rtc);
+	free_irq(rtc->irq, rtc);
 
 	rtc_device_unregister(rtc->rtcdev);
 
@@ -423,7 +431,7 @@
 	rtc->imr = mr & (AT91_RTT_ALMIEN | AT91_RTT_RTTINCIEN);
 	if (rtc->imr) {
 		if (device_may_wakeup(&pdev->dev) && (mr & AT91_RTT_ALMIEN)) {
-			enable_irq_wake(AT91_ID_SYS);
+			enable_irq_wake(rtc->irq);
 			/* don't let RTTINC cause wakeups */
 			if (mr & AT91_RTT_RTTINCIEN)
 				rtt_writel(rtc, MR, mr & ~AT91_RTT_RTTINCIEN);
@@ -441,7 +449,7 @@
 
 	if (rtc->imr) {
 		if (device_may_wakeup(&pdev->dev))
-			disable_irq_wake(AT91_ID_SYS);
+			disable_irq_wake(rtc->irq);
 		mr = rtt_readl(rtc, MR);
 		rtt_writel(rtc, MR, mr | rtc->imr);
 	}
diff --git a/drivers/scsi/megaraid/megaraid_sas_base.c b/drivers/scsi/megaraid/megaraid_sas_base.c
index dc27598..ed38454 100644
--- a/drivers/scsi/megaraid/megaraid_sas_base.c
+++ b/drivers/scsi/megaraid/megaraid_sas_base.c
@@ -4066,7 +4066,6 @@
 	spin_lock_init(&instance->cmd_pool_lock);
 	spin_lock_init(&instance->hba_lock);
 	spin_lock_init(&instance->completion_lock);
-	spin_lock_init(&poll_aen_lock);
 
 	mutex_init(&instance->aen_mutex);
 	mutex_init(&instance->reset_mutex);
@@ -5392,6 +5391,8 @@
 	printk(KERN_INFO "megasas: %s %s\n", MEGASAS_VERSION,
 	       MEGASAS_EXT_VERSION);
 
+	spin_lock_init(&poll_aen_lock);
+
 	support_poll_for_event = 2;
 	support_device_change = 1;
 
diff --git a/drivers/scsi/mpt2sas/mpt2sas_base.c b/drivers/scsi/mpt2sas/mpt2sas_base.c
index 9d46fcb..b25757d 100644
--- a/drivers/scsi/mpt2sas/mpt2sas_base.c
+++ b/drivers/scsi/mpt2sas/mpt2sas_base.c
@@ -2424,10 +2424,13 @@
 	}
 
 	/* command line tunables  for max controller queue depth */
-	if (max_queue_depth != -1)
-		max_request_credit = (max_queue_depth < facts->RequestCredit)
-		    ? max_queue_depth : facts->RequestCredit;
-	else
+	if (max_queue_depth != -1 && max_queue_depth != 0) {
+		max_request_credit = min_t(u16, max_queue_depth +
+			ioc->hi_priority_depth + ioc->internal_depth,
+			facts->RequestCredit);
+		if (max_request_credit > MAX_HBA_QUEUE_DEPTH)
+			max_request_credit =  MAX_HBA_QUEUE_DEPTH;
+	} else
 		max_request_credit = min_t(u16, facts->RequestCredit,
 		    MAX_HBA_QUEUE_DEPTH);
 
@@ -2502,7 +2505,7 @@
 	/* set the scsi host can_queue depth
 	 * with some internal commands that could be outstanding
 	 */
-	ioc->shost->can_queue = ioc->scsiio_depth - (2);
+	ioc->shost->can_queue = ioc->scsiio_depth;
 	dinitprintk(ioc, printk(MPT2SAS_INFO_FMT "scsi host: "
 	    "can_queue depth (%d)\n", ioc->name, ioc->shost->can_queue));
 
diff --git a/drivers/scsi/scsi_error.c b/drivers/scsi/scsi_error.c
index 4a6381c..de2337f 100644
--- a/drivers/scsi/scsi_error.c
+++ b/drivers/scsi/scsi_error.c
@@ -42,6 +42,8 @@
 
 #include <trace/events/scsi.h>
 
+static void scsi_eh_done(struct scsi_cmnd *scmd);
+
 #define SENSE_TIMEOUT		(10*HZ)
 
 /*
@@ -241,6 +243,14 @@
 	if (! scsi_command_normalize_sense(scmd, &sshdr))
 		return FAILED;	/* no valid sense data */
 
+	if (scmd->cmnd[0] == TEST_UNIT_READY && scmd->scsi_done != scsi_eh_done)
+		/*
+		 * nasty: for mid-layer issued TURs, we need to return the
+		 * actual sense data without any recovery attempt.  For eh
+		 * issued ones, we need to try to recover and interpret
+		 */
+		return SUCCESS;
+
 	if (scsi_sense_is_deferred(&sshdr))
 		return NEEDS_RETRY;
 
diff --git a/drivers/scsi/scsi_lib.c b/drivers/scsi/scsi_lib.c
index ffd7773..faa790f 100644
--- a/drivers/scsi/scsi_lib.c
+++ b/drivers/scsi/scsi_lib.c
@@ -776,7 +776,6 @@
 	}
 
 	if (req->cmd_type == REQ_TYPE_BLOCK_PC) { /* SG_IO ioctl from block level */
-		req->errors = result;
 		if (result) {
 			if (sense_valid && req->sense) {
 				/*
@@ -792,6 +791,10 @@
 			if (!sense_deferred)
 				error = __scsi_error_from_host_byte(cmd, result);
 		}
+		/*
+		 * __scsi_error_from_host_byte may have reset the host_byte
+		 */
+		req->errors = cmd->result;
 
 		req->resid_len = scsi_get_resid(cmd);
 
diff --git a/drivers/scsi/scsi_scan.c b/drivers/scsi/scsi_scan.c
index 56a9379..d947ffc 100644
--- a/drivers/scsi/scsi_scan.c
+++ b/drivers/scsi/scsi_scan.c
@@ -764,6 +764,16 @@
 	sdev->model = (char *) (sdev->inquiry + 16);
 	sdev->rev = (char *) (sdev->inquiry + 32);
 
+	if (strncmp(sdev->vendor, "ATA     ", 8) == 0) {
+		/*
+		 * sata emulation layer device.  This is a hack to work around
+		 * the SATL power management specifications which state that
+		 * when the SATL detects the device has gone into standby
+		 * mode, it shall respond with NOT READY.
+		 */
+		sdev->allow_restart = 1;
+	}
+
 	if (*bflags & BLIST_ISROM) {
 		sdev->type = TYPE_ROM;
 		sdev->removable = 1;
diff --git a/drivers/staging/android/android_alarm.h b/drivers/staging/android/android_alarm.h
index d0cafd6..f2ffd96 100644
--- a/drivers/staging/android/android_alarm.h
+++ b/drivers/staging/android/android_alarm.h
@@ -51,10 +51,12 @@
 #define ANDROID_ALARM_WAIT                  _IO('a', 1)
 
 #define ALARM_IOW(c, type, size)            _IOW('a', (c) | ((type) << 4), size)
+#define ALARM_IOR(c, type, size)            _IOR('a', (c) | ((type) << 4), size)
+
 /* Set alarm */
 #define ANDROID_ALARM_SET(type)             ALARM_IOW(2, type, struct timespec)
 #define ANDROID_ALARM_SET_AND_WAIT(type)    ALARM_IOW(3, type, struct timespec)
-#define ANDROID_ALARM_GET_TIME(type)        ALARM_IOW(4, type, struct timespec)
+#define ANDROID_ALARM_GET_TIME(type)        ALARM_IOR(4, type, struct timespec)
 #define ANDROID_ALARM_SET_RTC               _IOW('a', 5, struct timespec)
 #define ANDROID_ALARM_BASE_CMD(cmd)         (cmd & ~(_IOC(0, 0, 0xf0, 0)))
 #define ANDROID_ALARM_IOCTL_TO_TYPE(cmd)    (_IOC_NR(cmd) >> 4)
diff --git a/drivers/staging/comedi/drivers/amplc_dio200.c b/drivers/staging/comedi/drivers/amplc_dio200.c
index 6c81e377..cc8931f 100644
--- a/drivers/staging/comedi/drivers/amplc_dio200.c
+++ b/drivers/staging/comedi/drivers/amplc_dio200.c
@@ -1412,6 +1412,13 @@
 		dev_err(dev->class_dev, "BUG! cannot determine board type!\n");
 		return -EINVAL;
 	}
+	/*
+	 * Need to 'get' the PCI device to match the 'put' in dio200_detach().
+	 * TODO: Remove the pci_dev_get() and matching pci_dev_put() once
+	 * support for manual attachment of PCI devices via dio200_attach()
+	 * has been removed.
+	 */
+	pci_dev_get(pci_dev);
 	return dio200_pci_common_attach(dev, pci_dev);
 }
 
diff --git a/drivers/staging/comedi/drivers/amplc_pc236.c b/drivers/staging/comedi/drivers/amplc_pc236.c
index aabba98..f502879 100644
--- a/drivers/staging/comedi/drivers/amplc_pc236.c
+++ b/drivers/staging/comedi/drivers/amplc_pc236.c
@@ -565,6 +565,13 @@
 		dev_err(dev->class_dev, "BUG! cannot determine board type!\n");
 		return -EINVAL;
 	}
+	/*
+	 * Need to 'get' the PCI device to match the 'put' in pc236_detach().
+	 * TODO: Remove the pci_dev_get() and matching pci_dev_put() once
+	 * support for manual attachment of PCI devices via pc236_attach()
+	 * has been removed.
+	 */
+	pci_dev_get(pci_dev);
 	return pc236_pci_common_attach(dev, pci_dev);
 }
 
diff --git a/drivers/staging/comedi/drivers/amplc_pc263.c b/drivers/staging/comedi/drivers/amplc_pc263.c
index 40ec1ff..8191c4e 100644
--- a/drivers/staging/comedi/drivers/amplc_pc263.c
+++ b/drivers/staging/comedi/drivers/amplc_pc263.c
@@ -298,6 +298,13 @@
 		dev_err(dev->class_dev, "BUG! cannot determine board type!\n");
 		return -EINVAL;
 	}
+	/*
+	 * Need to 'get' the PCI device to match the 'put' in pc263_detach().
+	 * TODO: Remove the pci_dev_get() and matching pci_dev_put() once
+	 * support for manual attachment of PCI devices via pc263_attach()
+	 * has been removed.
+	 */
+	pci_dev_get(pci_dev);
 	return pc263_pci_common_attach(dev, pci_dev);
 }
 
diff --git a/drivers/staging/comedi/drivers/amplc_pci224.c b/drivers/staging/comedi/drivers/amplc_pci224.c
index 4e17f13..8bf109e 100644
--- a/drivers/staging/comedi/drivers/amplc_pci224.c
+++ b/drivers/staging/comedi/drivers/amplc_pci224.c
@@ -1503,6 +1503,13 @@
 			DRIVER_NAME ": BUG! cannot determine board type!\n");
 		return -EINVAL;
 	}
+	/*
+	 * Need to 'get' the PCI device to match the 'put' in pci224_detach().
+	 * TODO: Remove the pci_dev_get() and matching pci_dev_put() once
+	 * support for manual attachment of PCI devices via pci224_attach()
+	 * has been removed.
+	 */
+	pci_dev_get(pci_dev);
 	return pci224_attach_common(dev, pci_dev, NULL);
 }
 
diff --git a/drivers/staging/comedi/drivers/amplc_pci230.c b/drivers/staging/comedi/drivers/amplc_pci230.c
index 1b67d0c..66e74bd 100644
--- a/drivers/staging/comedi/drivers/amplc_pci230.c
+++ b/drivers/staging/comedi/drivers/amplc_pci230.c
@@ -2925,6 +2925,13 @@
 			"amplc_pci230: BUG! cannot determine board type!\n");
 		return -EINVAL;
 	}
+	/*
+	 * Need to 'get' the PCI device to match the 'put' in pci230_detach().
+	 * TODO: Remove the pci_dev_get() and matching pci_dev_put() once
+	 * support for manual attachment of PCI devices via pci230_attach()
+	 * has been removed.
+	 */
+	pci_dev_get(pci_dev);
 	return pci230_attach_common(dev, pci_dev);
 }
 
diff --git a/drivers/staging/comedi/drivers/das08.c b/drivers/staging/comedi/drivers/das08.c
index 874e02e..67a914a 100644
--- a/drivers/staging/comedi/drivers/das08.c
+++ b/drivers/staging/comedi/drivers/das08.c
@@ -378,7 +378,7 @@
 	int chan;
 
 	lsb = data[0] & 0xff;
-	msb = (data[0] >> 8) & 0xf;
+	msb = (data[0] >> 8) & 0xff;
 
 	chan = CR_CHAN(insn->chanspec);
 
@@ -623,7 +623,7 @@
 		.ai = das08_ai_rinsn,
 		.ai_nbits = 16,
 		.ai_pg = das08_pg_none,
-		.ai_encoding = das08_encode12,
+		.ai_encoding = das08_encode16,
 		.ao = das08jr_ao_winsn,
 		.ao_nbits = 16,
 		.di = das08jr_di_rbits,
@@ -922,6 +922,13 @@
 		dev_err(dev->class_dev, "BUG! cannot determine board type!\n");
 		return -EINVAL;
 	}
+	/*
+	 * Need to 'get' the PCI device to match the 'put' in das08_detach().
+	 * TODO: Remove the pci_dev_get() and matching pci_dev_put() once
+	 * support for manual attachment of PCI devices via das08_attach()
+	 * has been removed.
+	 */
+	pci_dev_get(pdev);
 	return das08_pci_attach_common(dev, pdev);
 }
 
diff --git a/drivers/staging/iio/accel/lis3l02dq_ring.c b/drivers/staging/iio/accel/lis3l02dq_ring.c
index 18d108f..f3da590 100644
--- a/drivers/staging/iio/accel/lis3l02dq_ring.c
+++ b/drivers/staging/iio/accel/lis3l02dq_ring.c
@@ -121,8 +121,10 @@
 	if (rx_array == NULL)
 		return -ENOMEM;
 	ret = lis3l02dq_read_all(indio_dev, rx_array);
-	if (ret < 0)
+	if (ret < 0) {
+		kfree(rx_array);
 		return ret;
+	}
 	for (i = 0; i < scan_count; i++)
 		data[i] = combine_8_to_16(rx_array[i*4+1],
 					rx_array[i*4+3]);
diff --git a/drivers/staging/iio/adc/ad7192.c b/drivers/staging/iio/adc/ad7192.c
index 0958372..19a064d 100644
--- a/drivers/staging/iio/adc/ad7192.c
+++ b/drivers/staging/iio/adc/ad7192.c
@@ -647,6 +647,8 @@
 	ret = strict_strtoul(buf, 10, &lval);
 	if (ret)
 		return ret;
+	if (lval == 0)
+		return -EINVAL;
 
 	mutex_lock(&indio_dev->mlock);
 	if (iio_buffer_enabled(indio_dev)) {
diff --git a/drivers/staging/iio/gyro/adis16260_core.c b/drivers/staging/iio/gyro/adis16260_core.c
index 93aa431..eb8e9d6 100644
--- a/drivers/staging/iio/gyro/adis16260_core.c
+++ b/drivers/staging/iio/gyro/adis16260_core.c
@@ -195,6 +195,8 @@
 	ret = strict_strtol(buf, 10, &val);
 	if (ret)
 		return ret;
+	if (val == 0)
+		return -EINVAL;
 
 	mutex_lock(&indio_dev->mlock);
 	if (spi_get_device_id(st->us)) {
diff --git a/drivers/staging/iio/imu/adis16400_core.c b/drivers/staging/iio/imu/adis16400_core.c
index 1f4c177..a618327 100644
--- a/drivers/staging/iio/imu/adis16400_core.c
+++ b/drivers/staging/iio/imu/adis16400_core.c
@@ -234,6 +234,8 @@
 	ret = strict_strtol(buf, 10, &val);
 	if (ret)
 		return ret;
+	if (val == 0)
+		return -EINVAL;
 
 	mutex_lock(&indio_dev->mlock);
 
diff --git a/drivers/staging/iio/meter/ade7753.c b/drivers/staging/iio/meter/ade7753.c
index f04ece7..3ccff18 100644
--- a/drivers/staging/iio/meter/ade7753.c
+++ b/drivers/staging/iio/meter/ade7753.c
@@ -425,6 +425,8 @@
 	ret = strict_strtol(buf, 10, &val);
 	if (ret)
 		return ret;
+	if (val == 0)
+		return -EINVAL;
 
 	mutex_lock(&indio_dev->mlock);
 
diff --git a/drivers/staging/iio/meter/ade7754.c b/drivers/staging/iio/meter/ade7754.c
index 6cee28a..abb1e9c 100644
--- a/drivers/staging/iio/meter/ade7754.c
+++ b/drivers/staging/iio/meter/ade7754.c
@@ -445,6 +445,8 @@
 	ret = strict_strtol(buf, 10, &val);
 	if (ret)
 		return ret;
+	if (val == 0)
+		return -EINVAL;
 
 	mutex_lock(&indio_dev->mlock);
 
diff --git a/drivers/staging/iio/meter/ade7759.c b/drivers/staging/iio/meter/ade7759.c
index b3f7e0fa9..eb0a2a9 100644
--- a/drivers/staging/iio/meter/ade7759.c
+++ b/drivers/staging/iio/meter/ade7759.c
@@ -385,6 +385,8 @@
 	ret = strict_strtol(buf, 10, &val);
 	if (ret)
 		return ret;
+	if (val == 0)
+		return -EINVAL;
 
 	mutex_lock(&indio_dev->mlock);
 
diff --git a/drivers/staging/omapdrm/omap_connector.c b/drivers/staging/omapdrm/omap_connector.c
index 5e2856c..55e9c86 100644
--- a/drivers/staging/omapdrm/omap_connector.c
+++ b/drivers/staging/omapdrm/omap_connector.c
@@ -48,13 +48,20 @@
 	mode->vsync_end = mode->vsync_start + timings->vsw;
 	mode->vtotal = mode->vsync_end + timings->vbp;
 
-	/* note: whether or not it is interlaced, +/- h/vsync, etc,
-	 * which should be set in the mode flags, is not exposed in
-	 * the omap_video_timings struct.. but hdmi driver tracks
-	 * those separately so all we have to have to set the mode
-	 * is the way to recover these timings values, and the
-	 * omap_dss_driver would do the rest.
-	 */
+	mode->flags = 0;
+
+	if (timings->interlace)
+		mode->flags |= DRM_MODE_FLAG_INTERLACE;
+
+	if (timings->hsync_level == OMAPDSS_SIG_ACTIVE_HIGH)
+		mode->flags |= DRM_MODE_FLAG_PHSYNC;
+	else
+		mode->flags |= DRM_MODE_FLAG_NHSYNC;
+
+	if (timings->vsync_level == OMAPDSS_SIG_ACTIVE_HIGH)
+		mode->flags |= DRM_MODE_FLAG_PVSYNC;
+	else
+		mode->flags |= DRM_MODE_FLAG_NVSYNC;
 }
 
 static inline void copy_timings_drm_to_omap(struct omap_video_timings *timings,
@@ -71,6 +78,22 @@
 	timings->vfp = mode->vsync_start - mode->vdisplay;
 	timings->vsw = mode->vsync_end - mode->vsync_start;
 	timings->vbp = mode->vtotal - mode->vsync_end;
+
+	timings->interlace = !!(mode->flags & DRM_MODE_FLAG_INTERLACE);
+
+	if (mode->flags & DRM_MODE_FLAG_PHSYNC)
+		timings->hsync_level = OMAPDSS_SIG_ACTIVE_HIGH;
+	else
+		timings->hsync_level = OMAPDSS_SIG_ACTIVE_LOW;
+
+	if (mode->flags & DRM_MODE_FLAG_PVSYNC)
+		timings->vsync_level = OMAPDSS_SIG_ACTIVE_HIGH;
+	else
+		timings->vsync_level = OMAPDSS_SIG_ACTIVE_LOW;
+
+	timings->data_pclk_edge = OMAPDSS_DRIVE_SIG_RISING_EDGE;
+	timings->de_level = OMAPDSS_SIG_ACTIVE_HIGH;
+	timings->sync_pclk_edge = OMAPDSS_DRIVE_SIG_OPPOSITE_EDGES;
 }
 
 static void omap_connector_dpms(struct drm_connector *connector, int mode)
@@ -187,7 +210,7 @@
 		}
 	} else {
 		struct drm_display_mode *mode = drm_mode_create(dev);
-		struct omap_video_timings timings;
+		struct omap_video_timings timings = {0};
 
 		dssdrv->get_timings(dssdev, &timings);
 
@@ -291,7 +314,7 @@
 	struct omap_connector *omap_connector = to_omap_connector(connector);
 	struct omap_dss_device *dssdev = omap_connector->dssdev;
 	struct omap_dss_driver *dssdrv = dssdev->driver;
-	struct omap_video_timings timings;
+	struct omap_video_timings timings = {0};
 
 	copy_timings_drm_to_omap(&timings, mode);
 
diff --git a/drivers/staging/ozwpan/ozcdev.c b/drivers/staging/ozwpan/ozcdev.c
index d983219..758ce0a 100644
--- a/drivers/staging/ozwpan/ozcdev.c
+++ b/drivers/staging/ozwpan/ozcdev.c
@@ -8,6 +8,7 @@
 #include <linux/cdev.h>
 #include <linux/uaccess.h>
 #include <linux/netdevice.h>
+#include <linux/etherdevice.h>
 #include <linux/poll.h>
 #include <linux/sched.h>
 #include "ozconfig.h"
@@ -213,7 +214,7 @@
 		if (old_pd)
 			oz_pd_put(old_pd);
 	} else {
-		if (!memcmp(addr, "\0\0\0\0\0\0", sizeof(addr))) {
+		if (is_zero_ether_addr(addr)) {
 			spin_lock_bh(&g_cdev.lock);
 			pd = g_cdev.active_pd;
 			g_cdev.active_pd = 0;
diff --git a/drivers/staging/rtl8712/recv_linux.c b/drivers/staging/rtl8712/recv_linux.c
index 0e26d5f..495ee12 100644
--- a/drivers/staging/rtl8712/recv_linux.c
+++ b/drivers/staging/rtl8712/recv_linux.c
@@ -117,13 +117,8 @@
 	if (skb == NULL)
 		goto _recv_indicatepkt_drop;
 	skb->data = precv_frame->u.hdr.rx_data;
-#ifdef NET_SKBUFF_DATA_USES_OFFSET
-	skb->tail = (sk_buff_data_t)(precv_frame->u.hdr.rx_tail -
-		     precv_frame->u.hdr.rx_head);
-#else
-	skb->tail = (sk_buff_data_t)precv_frame->u.hdr.rx_tail;
-#endif
 	skb->len = precv_frame->u.hdr.len;
+	skb_set_tail_pointer(skb, skb->len);
 	if ((pattrib->tcpchk_valid == 1) && (pattrib->tcp_chkrpt == 1))
 		skb->ip_summed = CHECKSUM_UNNECESSARY;
 	else
diff --git a/drivers/staging/vt6656/dpc.c b/drivers/staging/vt6656/dpc.c
index e4bdf2a..3aa895e 100644
--- a/drivers/staging/vt6656/dpc.c
+++ b/drivers/staging/vt6656/dpc.c
@@ -200,7 +200,7 @@
     } else if (!compare_ether_addr(pbyRxBuffer, &pDevice->abySNAP_RFC1042[0])) {
         cbHeaderSize += 6;
         pwType = (PWORD) (pbyRxBufferAddr + cbHeaderSize);
-	if ((*pwType == cpu_to_le16(ETH_P_IPX)) ||
+	if ((*pwType == cpu_to_be16(ETH_P_IPX)) ||
 	    (*pwType == cpu_to_le16(0xF380))) {
 		cbHeaderSize -= 8;
             pwType = (PWORD) (pbyRxBufferAddr + cbHeaderSize);
diff --git a/drivers/staging/vt6656/rxtx.c b/drivers/staging/vt6656/rxtx.c
index bb464527..b6e04e7 100644
--- a/drivers/staging/vt6656/rxtx.c
+++ b/drivers/staging/vt6656/rxtx.c
@@ -1699,7 +1699,7 @@
     // 802.1H
     if (ntohs(psEthHeader->wType) > ETH_DATA_LEN) {
 	if (pDevice->dwDiagRefCount == 0) {
-		if ((psEthHeader->wType == cpu_to_le16(ETH_P_IPX)) ||
+		if ((psEthHeader->wType == cpu_to_be16(ETH_P_IPX)) ||
 		    (psEthHeader->wType == cpu_to_le16(0xF380))) {
 			memcpy((PBYTE) (pbyPayloadHead),
 			       abySNAP_Bridgetunnel, 6);
@@ -2838,10 +2838,10 @@
     Packet_Type = skb->data[ETH_HLEN+1];
     Descriptor_type = skb->data[ETH_HLEN+1+1+2];
     Key_info = (skb->data[ETH_HLEN+1+1+2+1] << 8)|(skb->data[ETH_HLEN+1+1+2+2]);
-    if (pDevice->sTxEthHeader.wType == cpu_to_le16(ETH_P_PAE)) {
-	/* 802.1x OR eapol-key challenge frame transfer */
-	if (((Protocol_Version == 1) || (Protocol_Version == 2)) &&
-		(Packet_Type == 3)) {
+	if (pDevice->sTxEthHeader.wType == cpu_to_be16(ETH_P_PAE)) {
+		/* 802.1x OR eapol-key challenge frame transfer */
+		if (((Protocol_Version == 1) || (Protocol_Version == 2)) &&
+			(Packet_Type == 3)) {
                         bTxeapol_key = TRUE;
                        if(!(Key_info & BIT3) &&  //WPA or RSN group-key challenge
 			   (Key_info & BIT8) && (Key_info & BIT9)) {    //send 2/2 key
@@ -2987,19 +2987,19 @@
         }
     }
 
-    if (pDevice->sTxEthHeader.wType == cpu_to_le16(ETH_P_PAE)) {
-        if (pDevice->byBBType != BB_TYPE_11A) {
-            pDevice->wCurrentRate = RATE_1M;
-            pDevice->byACKRate = RATE_1M;
-            pDevice->byTopCCKBasicRate = RATE_1M;
-            pDevice->byTopOFDMBasicRate = RATE_6M;
-        } else {
-            pDevice->wCurrentRate = RATE_6M;
-            pDevice->byACKRate = RATE_6M;
-            pDevice->byTopCCKBasicRate = RATE_1M;
-            pDevice->byTopOFDMBasicRate = RATE_6M;
-        }
-    }
+	if (pDevice->sTxEthHeader.wType == cpu_to_be16(ETH_P_PAE)) {
+		if (pDevice->byBBType != BB_TYPE_11A) {
+			pDevice->wCurrentRate = RATE_1M;
+			pDevice->byACKRate = RATE_1M;
+			pDevice->byTopCCKBasicRate = RATE_1M;
+			pDevice->byTopOFDMBasicRate = RATE_6M;
+		} else {
+			pDevice->wCurrentRate = RATE_6M;
+			pDevice->byACKRate = RATE_6M;
+			pDevice->byTopCCKBasicRate = RATE_1M;
+			pDevice->byTopOFDMBasicRate = RATE_6M;
+		}
+	}
 
     DBG_PRT(MSG_LEVEL_DEBUG,
 	    KERN_INFO "dma_tx: pDevice->wCurrentRate = %d\n",
@@ -3015,7 +3015,7 @@
 
     if (bNeedEncryption == TRUE) {
         DBG_PRT(MSG_LEVEL_DEBUG, KERN_INFO"ntohs Pkt Type=%04x\n", ntohs(pDevice->sTxEthHeader.wType));
-	if ((pDevice->sTxEthHeader.wType) == cpu_to_le16(ETH_P_PAE)) {
+	if ((pDevice->sTxEthHeader.wType) == cpu_to_be16(ETH_P_PAE)) {
 		bNeedEncryption = FALSE;
             DBG_PRT(MSG_LEVEL_DEBUG, KERN_INFO"Pkt Type=%04x\n", (pDevice->sTxEthHeader.wType));
             if ((pMgmt->eCurrMode == WMAC_MODE_ESS_STA) && (pMgmt->eCurrState == WMAC_STATE_ASSOC)) {
diff --git a/drivers/staging/wlan-ng/cfg80211.c b/drivers/staging/wlan-ng/cfg80211.c
index fabff4d..0970127 100644
--- a/drivers/staging/wlan-ng/cfg80211.c
+++ b/drivers/staging/wlan-ng/cfg80211.c
@@ -327,9 +327,9 @@
 	return result;
 }
 
-int prism2_scan(struct wiphy *wiphy, struct net_device *dev,
-		struct cfg80211_scan_request *request)
+int prism2_scan(struct wiphy *wiphy, struct cfg80211_scan_request *request)
 {
+	struct net_device *dev = request->wdev->netdev;
 	struct prism2_wiphy_private *priv = wiphy_priv(wiphy);
 	wlandevice_t *wlandev = dev->ml_priv;
 	struct p80211msg_dot11req_scan msg1;
diff --git a/drivers/staging/zcache/zcache-main.c b/drivers/staging/zcache/zcache-main.c
index c214977..52b43b7 100644
--- a/drivers/staging/zcache/zcache-main.c
+++ b/drivers/staging/zcache/zcache-main.c
@@ -1251,13 +1251,12 @@
 					void *pampd, struct tmem_pool *pool,
 					struct tmem_oid *oid, uint32_t index)
 {
-	int ret = 0;
-
 	BUG_ON(!is_ephemeral(pool));
-	zbud_decompress((struct page *)(data), pampd);
+	if (zbud_decompress((struct page *)(data), pampd) < 0)
+		return -EINVAL;
 	zbud_free_and_delist((struct zbud_hdr *)pampd);
 	atomic_dec(&zcache_curr_eph_pampd_count);
-	return ret;
+	return 0;
 }
 
 /*
diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index d5c689d6..e309e8b 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -132,6 +132,7 @@
 #define  UCR4_OREN  	 (1<<1)  /* Receiver overrun interrupt enable */
 #define  UCR4_DREN  	 (1<<0)  /* Recv data ready interrupt enable */
 #define  UFCR_RXTL_SHF   0       /* Receiver trigger level shift */
+#define  UFCR_DCEDTE	 (1<<6)  /* DCE/DTE mode select */
 #define  UFCR_RFDIV      (7<<7)  /* Reference freq divider mask */
 #define  UFCR_RFDIV_REG(x)	(((x) < 7 ? 6 - (x) : 6) << 7)
 #define  UFCR_TXTL_SHF   10      /* Transmitter trigger level shift */
@@ -667,22 +668,11 @@
 static int imx_setup_ufcr(struct imx_port *sport, unsigned int mode)
 {
 	unsigned int val;
-	unsigned int ufcr_rfdiv;
 
-	/* set receiver / transmitter trigger level.
-	 * RFDIV is set such way to satisfy requested uartclk value
-	 */
-	val = TXTL << 10 | RXTL;
-	ufcr_rfdiv = (clk_get_rate(sport->clk_per) + sport->port.uartclk / 2)
-			/ sport->port.uartclk;
-
-	if(!ufcr_rfdiv)
-		ufcr_rfdiv = 1;
-
-	val |= UFCR_RFDIV_REG(ufcr_rfdiv);
-
+	/* set receiver / transmitter trigger level */
+	val = readl(sport->port.membase + UFCR) & (UFCR_RFDIV | UFCR_DCEDTE);
+	val |= TXTL << UFCR_TXTL_SHF | RXTL;
 	writel(val, sport->port.membase + UFCR);
-
 	return 0;
 }
 
@@ -754,6 +744,7 @@
 		}
 	}
 
+	spin_lock_irqsave(&sport->port.lock, flags);
 	/*
 	 * Finally, clear and enable interrupts
 	 */
@@ -807,7 +798,6 @@
 	/*
 	 * Enable modem status interrupts
 	 */
-	spin_lock_irqsave(&sport->port.lock,flags);
 	imx_enable_ms(&sport->port);
 	spin_unlock_irqrestore(&sport->port.lock,flags);
 
@@ -837,10 +827,13 @@
 {
 	struct imx_port *sport = (struct imx_port *)port;
 	unsigned long temp;
+	unsigned long flags;
 
+	spin_lock_irqsave(&sport->port.lock, flags);
 	temp = readl(sport->port.membase + UCR2);
 	temp &= ~(UCR2_TXEN);
 	writel(temp, sport->port.membase + UCR2);
+	spin_unlock_irqrestore(&sport->port.lock, flags);
 
 	if (USE_IRDA(sport)) {
 		struct imxuart_platform_data *pdata;
@@ -869,12 +862,14 @@
 	 * Disable all interrupts, port and break condition.
 	 */
 
+	spin_lock_irqsave(&sport->port.lock, flags);
 	temp = readl(sport->port.membase + UCR1);
 	temp &= ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN | UCR1_UARTEN);
 	if (USE_IRDA(sport))
 		temp &= ~(UCR1_IREN);
 
 	writel(temp, sport->port.membase + UCR1);
+	spin_unlock_irqrestore(&sport->port.lock, flags);
 }
 
 static void
@@ -1217,6 +1212,9 @@
 	struct imx_port *sport = imx_ports[co->index];
 	struct imx_port_ucrs old_ucr;
 	unsigned int ucr1;
+	unsigned long flags;
+
+	spin_lock_irqsave(&sport->port.lock, flags);
 
 	/*
 	 *	First, save UCR1/2/3 and then disable interrupts
@@ -1242,6 +1240,8 @@
 	while (!(readl(sport->port.membase + USR2) & USR2_TXDC));
 
 	imx_port_ucrs_restore(&sport->port, &old_ucr);
+
+	spin_unlock_irqrestore(&sport->port.lock, flags);
 }
 
 /*
diff --git a/drivers/usb/chipidea/udc.c b/drivers/usb/chipidea/udc.c
index c7a032a..d214448 100644
--- a/drivers/usb/chipidea/udc.c
+++ b/drivers/usb/chipidea/udc.c
@@ -78,8 +78,7 @@
 }
 
 /**
- * hw_device_state: enables/disables interrupts & starts/stops device (execute
- *                  without interruption)
+ * hw_device_state: enables/disables interrupts (execute without interruption)
  * @dma: 0 => disable, !0 => enable and set dma engine
  *
  * This function returns an error code
@@ -91,9 +90,7 @@
 		/* interrupt, error, port change, reset, sleep/suspend */
 		hw_write(ci, OP_USBINTR, ~0,
 			     USBi_UI|USBi_UEI|USBi_PCI|USBi_URI|USBi_SLI);
-		hw_write(ci, OP_USBCMD, USBCMD_RS, USBCMD_RS);
 	} else {
-		hw_write(ci, OP_USBCMD, USBCMD_RS, 0);
 		hw_write(ci, OP_USBINTR, ~0, 0);
 	}
 	return 0;
@@ -774,10 +771,7 @@
 {
 	struct ci13xxx_req *mReq, *mReqTemp;
 	struct ci13xxx_ep *mEpTemp = mEp;
-	int uninitialized_var(retval);
-
-	if (list_empty(&mEp->qh.queue))
-		return -EINVAL;
+	int retval = 0;
 
 	list_for_each_entry_safe(mReq, mReqTemp, &mEp->qh.queue,
 			queue) {
@@ -1420,6 +1414,21 @@
 	return -ENOTSUPP;
 }
 
+/* Change Data+ pullup status
+ * this func is used by usb_gadget_connect/disconnet
+ */
+static int ci13xxx_pullup(struct usb_gadget *_gadget, int is_on)
+{
+	struct ci13xxx *ci = container_of(_gadget, struct ci13xxx, gadget);
+
+	if (is_on)
+		hw_write(ci, OP_USBCMD, USBCMD_RS, USBCMD_RS);
+	else
+		hw_write(ci, OP_USBCMD, USBCMD_RS, 0);
+
+	return 0;
+}
+
 static int ci13xxx_start(struct usb_gadget *gadget,
 			 struct usb_gadget_driver *driver);
 static int ci13xxx_stop(struct usb_gadget *gadget,
@@ -1432,6 +1441,7 @@
 static const struct usb_gadget_ops usb_gadget_ops = {
 	.vbus_session	= ci13xxx_vbus_session,
 	.wakeup		= ci13xxx_wakeup,
+	.pullup		= ci13xxx_pullup,
 	.vbus_draw	= ci13xxx_vbus_draw,
 	.udc_start	= ci13xxx_start,
 	.udc_stop	= ci13xxx_stop,
@@ -1455,7 +1465,12 @@
 
 			mEp->ep.name      = mEp->name;
 			mEp->ep.ops       = &usb_ep_ops;
-			mEp->ep.maxpacket = CTRL_PAYLOAD_MAX;
+			/*
+			 * for ep0: maxP defined in desc, for other
+			 * eps, maxP is set by epautoconfig() called
+			 * by gadget layer
+			 */
+			mEp->ep.maxpacket = (unsigned short)~0;
 
 			INIT_LIST_HEAD(&mEp->qh.queue);
 			mEp->qh.ptr = dma_pool_alloc(ci->qh_pool, GFP_KERNEL,
@@ -1475,6 +1490,7 @@
 				else
 					ci->ep0in = mEp;
 
+				mEp->ep.maxpacket = CTRL_PAYLOAD_MAX;
 				continue;
 			}
 
@@ -1484,6 +1500,17 @@
 	return retval;
 }
 
+static void destroy_eps(struct ci13xxx *ci)
+{
+	int i;
+
+	for (i = 0; i < ci->hw_ep_max; i++) {
+		struct ci13xxx_ep *mEp = &ci->ci13xxx_ep[i];
+
+		dma_pool_free(ci->qh_pool, mEp->qh.ptr, mEp->qh.dma);
+	}
+}
+
 /**
  * ci13xxx_start: register a gadget driver
  * @gadget: our gadget
@@ -1691,7 +1718,7 @@
 	if (ci->platdata->flags & CI13XXX_REQUIRE_TRANSCEIVER) {
 		if (ci->transceiver == NULL) {
 			retval = -ENODEV;
-			goto free_pools;
+			goto destroy_eps;
 		}
 	}
 
@@ -1729,7 +1756,7 @@
 
 remove_trans:
 	if (!IS_ERR_OR_NULL(ci->transceiver)) {
-		otg_set_peripheral(ci->transceiver->otg, &ci->gadget);
+		otg_set_peripheral(ci->transceiver->otg, NULL);
 		if (ci->global_phy)
 			usb_put_phy(ci->transceiver);
 	}
@@ -1742,6 +1769,8 @@
 put_transceiver:
 	if (!IS_ERR_OR_NULL(ci->transceiver) && ci->global_phy)
 		usb_put_phy(ci->transceiver);
+destroy_eps:
+	destroy_eps(ci);
 free_pools:
 	dma_pool_destroy(ci->td_pool);
 free_qh_pool:
@@ -1756,18 +1785,12 @@
  */
 static void udc_stop(struct ci13xxx *ci)
 {
-	int i;
-
 	if (ci == NULL)
 		return;
 
 	usb_del_gadget_udc(&ci->gadget);
 
-	for (i = 0; i < ci->hw_ep_max; i++) {
-		struct ci13xxx_ep *mEp = &ci->ci13xxx_ep[i];
-
-		dma_pool_free(ci->qh_pool, mEp->qh.ptr, mEp->qh.dma);
-	}
+	destroy_eps(ci);
 
 	dma_pool_destroy(ci->td_pool);
 	dma_pool_destroy(ci->qh_pool);
diff --git a/drivers/usb/class/cdc-wdm.c b/drivers/usb/class/cdc-wdm.c
index 65a55ab..5f0cb41 100644
--- a/drivers/usb/class/cdc-wdm.c
+++ b/drivers/usb/class/cdc-wdm.c
@@ -109,12 +109,14 @@
 /* return intfdata if we own the interface, else look up intf in the list */
 static struct wdm_device *wdm_find_device(struct usb_interface *intf)
 {
-	struct wdm_device *desc = NULL;
+	struct wdm_device *desc;
 
 	spin_lock(&wdm_device_list_lock);
 	list_for_each_entry(desc, &wdm_device_list, device_list)
 		if (desc->intf == intf)
-			break;
+			goto found;
+	desc = NULL;
+found:
 	spin_unlock(&wdm_device_list_lock);
 
 	return desc;
@@ -122,12 +124,14 @@
 
 static struct wdm_device *wdm_find_device_by_minor(int minor)
 {
-	struct wdm_device *desc = NULL;
+	struct wdm_device *desc;
 
 	spin_lock(&wdm_device_list_lock);
 	list_for_each_entry(desc, &wdm_device_list, device_list)
 		if (desc->intf->minor == minor)
-			break;
+			goto found;
+	desc = NULL;
+found:
 	spin_unlock(&wdm_device_list_lock);
 
 	return desc;
diff --git a/drivers/usb/core/quirks.c b/drivers/usb/core/quirks.c
index f15501f4c..e77a8e8 100644
--- a/drivers/usb/core/quirks.c
+++ b/drivers/usb/core/quirks.c
@@ -71,6 +71,10 @@
 	{ USB_DEVICE(0x04b4, 0x0526), .driver_info =
 			USB_QUIRK_CONFIG_INTF_STRINGS },
 
+	/* Microchip Joss Optical infrared touchboard device */
+	{ USB_DEVICE(0x04d8, 0x000c), .driver_info =
+			USB_QUIRK_CONFIG_INTF_STRINGS },
+
 	/* Samsung Android phone modem - ID conflict with SPH-I500 */
 	{ USB_DEVICE(0x04e8, 0x6601), .driver_info =
 			USB_QUIRK_CONFIG_INTF_STRINGS },
diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
index c34452a..a68ff53 100644
--- a/drivers/usb/dwc3/core.c
+++ b/drivers/usb/dwc3/core.c
@@ -436,16 +436,21 @@
 		dev_err(dev, "missing IRQ\n");
 		return -ENODEV;
 	}
-	dwc->xhci_resources[1] = *res;
+	dwc->xhci_resources[1].start = res->start;
+	dwc->xhci_resources[1].end = res->end;
+	dwc->xhci_resources[1].flags = res->flags;
+	dwc->xhci_resources[1].name = res->name;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (!res) {
 		dev_err(dev, "missing memory resource\n");
 		return -ENODEV;
 	}
-	dwc->xhci_resources[0] = *res;
+	dwc->xhci_resources[0].start = res->start;
 	dwc->xhci_resources[0].end = dwc->xhci_resources[0].start +
 					DWC3_XHCI_REGS_END;
+	dwc->xhci_resources[0].flags = res->flags;
+	dwc->xhci_resources[0].name = res->name;
 
 	 /*
 	  * Request memory region but exclude xHCI regs,
diff --git a/drivers/usb/dwc3/ep0.c b/drivers/usb/dwc3/ep0.c
index 9b94886..e4d5ca8 100644
--- a/drivers/usb/dwc3/ep0.c
+++ b/drivers/usb/dwc3/ep0.c
@@ -720,7 +720,6 @@
 		transferred = min_t(u32, ur->length,
 				transfer_size - length);
 		memcpy(ur->buf, dwc->ep0_bounce, transferred);
-		dwc->ep0_bounced = false;
 	} else {
 		transferred = ur->length - length;
 	}
diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
index 58fdfad..c2813c2b 100644
--- a/drivers/usb/dwc3/gadget.c
+++ b/drivers/usb/dwc3/gadget.c
@@ -263,8 +263,11 @@
 	if (req->request.status == -EINPROGRESS)
 		req->request.status = status;
 
-	usb_gadget_unmap_request(&dwc->gadget, &req->request,
-			req->direction);
+	if (dwc->ep0_bounced && dep->number == 0)
+		dwc->ep0_bounced = false;
+	else
+		usb_gadget_unmap_request(&dwc->gadget, &req->request,
+				req->direction);
 
 	dev_dbg(dwc->dev, "request %p from %s completed %d/%d ===> %d\n",
 			req, dep->name, req->request.actual,
@@ -1026,6 +1029,7 @@
 	if (list_empty(&dep->request_list)) {
 		dev_vdbg(dwc->dev, "ISOC ep %s run out for requests.\n",
 			dep->name);
+		dep->flags |= DWC3_EP_PENDING_REQUEST;
 		return;
 	}
 
@@ -1089,6 +1093,17 @@
 	if (dep->flags & DWC3_EP_PENDING_REQUEST) {
 		int	ret;
 
+		/*
+		 * If xfernotready is already elapsed and it is a case
+		 * of isoc transfer, then issue END TRANSFER, so that
+		 * you can receive xfernotready again and can have
+		 * notion of current microframe.
+		 */
+		if (usb_endpoint_xfer_isoc(dep->endpoint.desc)) {
+			dwc3_stop_active_transfer(dwc, dep->number);
+			return 0;
+		}
+
 		ret = __dwc3_gadget_kick_transfer(dep, 0, true);
 		if (ret && ret != -EBUSY) {
 			struct dwc3	*dwc = dep->dwc;
diff --git a/drivers/usb/gadget/at91_udc.c b/drivers/usb/gadget/at91_udc.c
index c9e66df..1e35963 100644
--- a/drivers/usb/gadget/at91_udc.c
+++ b/drivers/usb/gadget/at91_udc.c
@@ -475,8 +475,7 @@
 	unsigned long	flags;
 
 	if (!_ep || !ep
-			|| !desc || ep->ep.desc
-			|| _ep->name == ep0name
+			|| !desc || _ep->name == ep0name
 			|| desc->bDescriptorType != USB_DT_ENDPOINT
 			|| (maxpacket = usb_endpoint_maxp(desc)) == 0
 			|| maxpacket > ep->maxpacket) {
@@ -530,7 +529,6 @@
 	tmp |= AT91_UDP_EPEDS;
 	__raw_writel(tmp, ep->creg);
 
-	ep->ep.desc = desc;
 	ep->ep.maxpacket = maxpacket;
 
 	/*
@@ -1635,7 +1633,6 @@
 	udc->driver = driver;
 	udc->gadget.dev.driver = &driver->driver;
 	udc->gadget.dev.of_node = udc->pdev->dev.of_node;
-	dev_set_drvdata(&udc->gadget.dev, &driver->driver);
 	udc->enabled = 1;
 	udc->selfpowered = 1;
 
@@ -1656,7 +1653,6 @@
 	spin_unlock_irqrestore(&udc->lock, flags);
 
 	udc->gadget.dev.driver = NULL;
-	dev_set_drvdata(&udc->gadget.dev, NULL);
 	udc->driver = NULL;
 
 	DBG("unbound from %s\n", driver->driver.name);
diff --git a/drivers/usb/gadget/dummy_hcd.c b/drivers/usb/gadget/dummy_hcd.c
index b799106..afdbb1c 100644
--- a/drivers/usb/gadget/dummy_hcd.c
+++ b/drivers/usb/gadget/dummy_hcd.c
@@ -1916,6 +1916,27 @@
 	return retval;
 }
 
+/* usb 3.0 root hub device descriptor */
+struct {
+	struct usb_bos_descriptor bos;
+	struct usb_ss_cap_descriptor ss_cap;
+} __packed usb3_bos_desc = {
+
+	.bos = {
+		.bLength		= USB_DT_BOS_SIZE,
+		.bDescriptorType	= USB_DT_BOS,
+		.wTotalLength		= cpu_to_le16(sizeof(usb3_bos_desc)),
+		.bNumDeviceCaps		= 1,
+	},
+	.ss_cap = {
+		.bLength		= USB_DT_USB_SS_CAP_SIZE,
+		.bDescriptorType	= USB_DT_DEVICE_CAPABILITY,
+		.bDevCapabilityType	= USB_SS_CAP_TYPE,
+		.wSpeedSupported	= cpu_to_le16(USB_5GBPS_OPERATION),
+		.bFunctionalitySupport	= ilog2(USB_5GBPS_OPERATION),
+	},
+};
+
 static inline void
 ss_hub_descriptor(struct usb_hub_descriptor *desc)
 {
@@ -2006,6 +2027,18 @@
 		else
 			hub_descriptor((struct usb_hub_descriptor *) buf);
 		break;
+
+	case DeviceRequest | USB_REQ_GET_DESCRIPTOR:
+		if (hcd->speed != HCD_USB3)
+			goto error;
+
+		if ((wValue >> 8) != USB_DT_BOS)
+			goto error;
+
+		memcpy(buf, &usb3_bos_desc, sizeof(usb3_bos_desc));
+		retval = sizeof(usb3_bos_desc);
+		break;
+
 	case GetHubStatus:
 		*(__le32 *) buf = cpu_to_le32(0);
 		break;
@@ -2503,10 +2536,8 @@
 	hs_hcd->has_tt = 1;
 
 	retval = usb_add_hcd(hs_hcd, 0, 0);
-	if (retval != 0) {
-		usb_put_hcd(hs_hcd);
-		return retval;
-	}
+	if (retval)
+		goto put_usb2_hcd;
 
 	if (mod_data.is_super_speed) {
 		ss_hcd = usb_create_shared_hcd(&dummy_hcd, &pdev->dev,
@@ -2525,6 +2556,8 @@
 put_usb3_hcd:
 	usb_put_hcd(ss_hcd);
 dealloc_usb2_hcd:
+	usb_remove_hcd(hs_hcd);
+put_usb2_hcd:
 	usb_put_hcd(hs_hcd);
 	the_controller.hs_hcd = the_controller.ss_hcd = NULL;
 	return retval;
diff --git a/drivers/usb/gadget/f_fs.c b/drivers/usb/gadget/f_fs.c
index 8adc79d..829aba7 100644
--- a/drivers/usb/gadget/f_fs.c
+++ b/drivers/usb/gadget/f_fs.c
@@ -34,11 +34,15 @@
 /* Debugging ****************************************************************/
 
 #ifdef VERBOSE_DEBUG
+#ifndef pr_vdebug
 #  define pr_vdebug pr_debug
+#endif /* pr_vdebug */
 #  define ffs_dump_mem(prefix, ptr, len) \
 	print_hex_dump_bytes(pr_fmt(prefix ": "), DUMP_PREFIX_NONE, ptr, len)
 #else
+#ifndef pr_vdebug
 #  define pr_vdebug(...)                 do { } while (0)
+#endif /* pr_vdebug */
 #  define ffs_dump_mem(prefix, ptr, len) do { } while (0)
 #endif /* VERBOSE_DEBUG */
 
diff --git a/drivers/usb/gadget/s3c-hsotg.c b/drivers/usb/gadget/s3c-hsotg.c
index b13e0bb..0bb617e 100644
--- a/drivers/usb/gadget/s3c-hsotg.c
+++ b/drivers/usb/gadget/s3c-hsotg.c
@@ -3599,6 +3599,7 @@
 
 	if (hsotg->num_of_eps == 0) {
 		dev_err(dev, "wrong number of EPs (zero)\n");
+		ret = -EINVAL;
 		goto err_supplies;
 	}
 
@@ -3606,6 +3607,7 @@
 		      GFP_KERNEL);
 	if (!eps) {
 		dev_err(dev, "cannot get memory\n");
+		ret = -ENOMEM;
 		goto err_supplies;
 	}
 
@@ -3622,6 +3624,7 @@
 						     GFP_KERNEL);
 	if (!hsotg->ctrl_req) {
 		dev_err(dev, "failed to allocate ctrl req\n");
+		ret = -ENOMEM;
 		goto err_ep_mem;
 	}
 
diff --git a/drivers/usb/gadget/u_serial.c b/drivers/usb/gadget/u_serial.c
index 5b3f5ff..da6d479 100644
--- a/drivers/usb/gadget/u_serial.c
+++ b/drivers/usb/gadget/u_serial.c
@@ -132,11 +132,15 @@
 
 
 #ifdef VERBOSE_DEBUG
+#ifndef pr_vdebug
 #define pr_vdebug(fmt, arg...) \
 	pr_debug(fmt, ##arg)
+#endif /* pr_vdebug */
 #else
+#ifndef pr_vdebig
 #define pr_vdebug(fmt, arg...) \
 	({ if (0) pr_debug(fmt, ##arg); })
+#endif /* pr_vdebug */
 #endif
 
 /*-------------------------------------------------------------------------*/
diff --git a/drivers/usb/host/ehci-q.c b/drivers/usb/host/ehci-q.c
index 9bc39ca..4b66374 100644
--- a/drivers/usb/host/ehci-q.c
+++ b/drivers/usb/host/ehci-q.c
@@ -128,9 +128,17 @@
 	else {
 		qtd = list_entry (qh->qtd_list.next,
 				struct ehci_qtd, qtd_list);
-		/* first qtd may already be partially processed */
-		if (cpu_to_hc32(ehci, qtd->qtd_dma) == qh->hw->hw_current)
+		/*
+		 * first qtd may already be partially processed.
+		 * If we come here during unlink, the QH overlay region
+		 * might have reference to the just unlinked qtd. The
+		 * qtd is updated in qh_completions(). Update the QH
+		 * overlay here.
+		 */
+		if (cpu_to_hc32(ehci, qtd->qtd_dma) == qh->hw->hw_current) {
+			qh->hw->hw_qtd_next = qtd->hw_next;
 			qtd = NULL;
+		}
 	}
 
 	if (qtd)
diff --git a/drivers/usb/host/ohci-at91.c b/drivers/usb/host/ohci-at91.c
index a665b3e..aaa8d2b 100644
--- a/drivers/usb/host/ohci-at91.c
+++ b/drivers/usb/host/ohci-at91.c
@@ -570,6 +570,16 @@
 
 	if (pdata) {
 		at91_for_each_port(i) {
+			/*
+			 * do not configure PIO if not in relation with
+			 * real USB port on board
+			 */
+			if (i >= pdata->ports) {
+				pdata->vbus_pin[i] = -EINVAL;
+				pdata->overcurrent_pin[i] = -EINVAL;
+				break;
+			}
+
 			if (!gpio_is_valid(pdata->vbus_pin[i]))
 				continue;
 			gpio = pdata->vbus_pin[i];
diff --git a/drivers/usb/host/pci-quirks.c b/drivers/usb/host/pci-quirks.c
index c5e9e4a..966d148 100644
--- a/drivers/usb/host/pci-quirks.c
+++ b/drivers/usb/host/pci-quirks.c
@@ -75,7 +75,9 @@
 #define	NB_PIF0_PWRDOWN_1	0x01100013
 
 #define USB_INTEL_XUSB2PR      0xD0
+#define USB_INTEL_USB2PRM      0xD4
 #define USB_INTEL_USB3_PSSEN   0xD8
+#define USB_INTEL_USB3PRM      0xDC
 
 static struct amd_chipset_info {
 	struct pci_dev	*nb_dev;
@@ -772,10 +774,18 @@
 		return;
 	}
 
-	ports_available = 0xffffffff;
+	/* Read USB3PRM, the USB 3.0 Port Routing Mask Register
+	 * Indicate the ports that can be changed from OS.
+	 */
+	pci_read_config_dword(xhci_pdev, USB_INTEL_USB3PRM,
+			&ports_available);
+
+	dev_dbg(&xhci_pdev->dev, "Configurable ports to enable SuperSpeed: 0x%x\n",
+			ports_available);
+
 	/* Write USB3_PSSEN, the USB 3.0 Port SuperSpeed Enable
-	 * Register, to turn on SuperSpeed terminations for all
-	 * available ports.
+	 * Register, to turn on SuperSpeed terminations for the
+	 * switchable ports.
 	 */
 	pci_write_config_dword(xhci_pdev, USB_INTEL_USB3_PSSEN,
 			cpu_to_le32(ports_available));
@@ -785,7 +795,16 @@
 	dev_dbg(&xhci_pdev->dev, "USB 3.0 ports that are now enabled "
 			"under xHCI: 0x%x\n", ports_available);
 
-	ports_available = 0xffffffff;
+	/* Read XUSB2PRM, xHCI USB 2.0 Port Routing Mask Register
+	 * Indicate the USB 2.0 ports to be controlled by the xHCI host.
+	 */
+
+	pci_read_config_dword(xhci_pdev, USB_INTEL_USB2PRM,
+			&ports_available);
+
+	dev_dbg(&xhci_pdev->dev, "Configurable USB 2.0 ports to hand over to xCHI: 0x%x\n",
+			ports_available);
+
 	/* Write XUSB2PR, the xHC USB 2.0 Port Routing Register, to
 	 * switch the USB 2.0 power and data lines over to the xHCI
 	 * host.
@@ -822,12 +841,12 @@
 	void __iomem *op_reg_base;
 	u32 val;
 	int timeout;
+	int len = pci_resource_len(pdev, 0);
 
 	if (!mmio_resource_enabled(pdev, 0))
 		return;
 
-	base = ioremap_nocache(pci_resource_start(pdev, 0),
-				pci_resource_len(pdev, 0));
+	base = ioremap_nocache(pci_resource_start(pdev, 0), len);
 	if (base == NULL)
 		return;
 
@@ -837,9 +856,17 @@
 	 */
 	ext_cap_offset = xhci_find_next_cap_offset(base, XHCI_HCC_PARAMS_OFFSET);
 	do {
+		if ((ext_cap_offset + sizeof(val)) > len) {
+			/* We're reading garbage from the controller */
+			dev_warn(&pdev->dev,
+				 "xHCI controller failing to respond");
+			return;
+		}
+
 		if (!ext_cap_offset)
 			/* We've reached the end of the extended capabilities */
 			goto hc_init;
+
 		val = readl(base + ext_cap_offset);
 		if (XHCI_EXT_CAPS_ID(val) == XHCI_EXT_CAPS_LEGACY)
 			break;
@@ -870,9 +897,10 @@
 	/* Disable any BIOS SMIs and clear all SMI events*/
 	writel(val, base + ext_cap_offset + XHCI_LEGACY_CONTROL_OFFSET);
 
+hc_init:
 	if (usb_is_intel_switchable_xhci(pdev))
 		usb_enable_xhci_ports(pdev);
-hc_init:
+
 	op_reg_base = base + XHCI_HC_LENGTH(readl(base));
 
 	/* Wait for the host controller to be ready before writing any
diff --git a/drivers/usb/host/pci-quirks.h b/drivers/usb/host/pci-quirks.h
index ef004a5..7f69a39 100644
--- a/drivers/usb/host/pci-quirks.h
+++ b/drivers/usb/host/pci-quirks.h
@@ -15,6 +15,7 @@
 static inline void usb_amd_quirk_pll_disable(void) {}
 static inline void usb_amd_quirk_pll_enable(void) {}
 static inline void usb_amd_dev_put(void) {}
+static inline void usb_disable_xhci_ports(struct pci_dev *xhci_pdev) {}
 #endif  /* CONFIG_PCI */
 
 #endif  /*  __LINUX_USB_PCI_QUIRKS_H  */
diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c
index 74bfc86..d5eb357 100644
--- a/drivers/usb/host/xhci-hub.c
+++ b/drivers/usb/host/xhci-hub.c
@@ -493,11 +493,48 @@
 		 * when this bit is set.
 		 */
 		pls |= USB_PORT_STAT_CONNECTION;
+	} else {
+		/*
+		 * If CAS bit isn't set but the Port is already at
+		 * Compliance Mode, fake a connection so the USB core
+		 * notices the Compliance state and resets the port.
+		 * This resolves an issue generated by the SN65LVPE502CP
+		 * in which sometimes the port enters compliance mode
+		 * caused by a delay on the host-device negotiation.
+		 */
+		if (pls == USB_SS_PORT_LS_COMP_MOD)
+			pls |= USB_PORT_STAT_CONNECTION;
 	}
+
 	/* update status field */
 	*status |= pls;
 }
 
+/*
+ * Function for Compliance Mode Quirk.
+ *
+ * This Function verifies if all xhc USB3 ports have entered U0, if so,
+ * the compliance mode timer is deleted. A port won't enter
+ * compliance mode if it has previously entered U0.
+ */
+void xhci_del_comp_mod_timer(struct xhci_hcd *xhci, u32 status, u16 wIndex)
+{
+	u32 all_ports_seen_u0 = ((1 << xhci->num_usb3_ports)-1);
+	bool port_in_u0 = ((status & PORT_PLS_MASK) == XDEV_U0);
+
+	if (!(xhci->quirks & XHCI_COMP_MODE_QUIRK))
+		return;
+
+	if ((xhci->port_status_u0 != all_ports_seen_u0) && port_in_u0) {
+		xhci->port_status_u0 |= 1 << wIndex;
+		if (xhci->port_status_u0 == all_ports_seen_u0) {
+			del_timer_sync(&xhci->comp_mode_recovery_timer);
+			xhci_dbg(xhci, "All USB3 ports have entered U0 already!\n");
+			xhci_dbg(xhci, "Compliance Mode Recovery Timer Deleted.\n");
+		}
+	}
+}
+
 int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
 		u16 wIndex, char *buf, u16 wLength)
 {
@@ -651,6 +688,11 @@
 		/* Update Port Link State for super speed ports*/
 		if (hcd->speed == HCD_USB3) {
 			xhci_hub_report_link_state(&status, temp);
+			/*
+			 * Verify if all USB3 Ports Have entered U0 already.
+			 * Delete Compliance Mode Timer if so.
+			 */
+			xhci_del_comp_mod_timer(xhci, temp, wIndex);
 		}
 		if (bus_state->port_c_suspend & (1 << wIndex))
 			status |= 1 << USB_PORT_FEAT_C_SUSPEND;
diff --git a/drivers/usb/host/xhci-plat.c b/drivers/usb/host/xhci-plat.c
index 689bc18..df90fe5 100644
--- a/drivers/usb/host/xhci-plat.c
+++ b/drivers/usb/host/xhci-plat.c
@@ -118,7 +118,7 @@
 		goto put_hcd;
 	}
 
-	hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
+	hcd->regs = ioremap_nocache(hcd->rsrc_start, hcd->rsrc_len);
 	if (!hcd->regs) {
 		dev_dbg(&pdev->dev, "error mapping memory\n");
 		ret = -EFAULT;
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index c59d5b5..6ece0ed 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -26,6 +26,7 @@
 #include <linux/module.h>
 #include <linux/moduleparam.h>
 #include <linux/slab.h>
+#include <linux/dmi.h>
 
 #include "xhci.h"
 
@@ -398,6 +399,95 @@
 
 #endif
 
+static void compliance_mode_recovery(unsigned long arg)
+{
+	struct xhci_hcd *xhci;
+	struct usb_hcd *hcd;
+	u32 temp;
+	int i;
+
+	xhci = (struct xhci_hcd *)arg;
+
+	for (i = 0; i < xhci->num_usb3_ports; i++) {
+		temp = xhci_readl(xhci, xhci->usb3_ports[i]);
+		if ((temp & PORT_PLS_MASK) == USB_SS_PORT_LS_COMP_MOD) {
+			/*
+			 * Compliance Mode Detected. Letting USB Core
+			 * handle the Warm Reset
+			 */
+			xhci_dbg(xhci, "Compliance Mode Detected->Port %d!\n",
+					i + 1);
+			xhci_dbg(xhci, "Attempting Recovery routine!\n");
+			hcd = xhci->shared_hcd;
+
+			if (hcd->state == HC_STATE_SUSPENDED)
+				usb_hcd_resume_root_hub(hcd);
+
+			usb_hcd_poll_rh_status(hcd);
+		}
+	}
+
+	if (xhci->port_status_u0 != ((1 << xhci->num_usb3_ports)-1))
+		mod_timer(&xhci->comp_mode_recovery_timer,
+			jiffies + msecs_to_jiffies(COMP_MODE_RCVRY_MSECS));
+}
+
+/*
+ * Quirk to work around issue generated by the SN65LVPE502CP USB3.0 re-driver
+ * that causes ports behind that hardware to enter compliance mode sometimes.
+ * The quirk creates a timer that polls every 2 seconds the link state of
+ * each host controller's port and recovers it by issuing a Warm reset
+ * if Compliance mode is detected, otherwise the port will become "dead" (no
+ * device connections or disconnections will be detected anymore). Becasue no
+ * status event is generated when entering compliance mode (per xhci spec),
+ * this quirk is needed on systems that have the failing hardware installed.
+ */
+static void compliance_mode_recovery_timer_init(struct xhci_hcd *xhci)
+{
+	xhci->port_status_u0 = 0;
+	init_timer(&xhci->comp_mode_recovery_timer);
+
+	xhci->comp_mode_recovery_timer.data = (unsigned long) xhci;
+	xhci->comp_mode_recovery_timer.function = compliance_mode_recovery;
+	xhci->comp_mode_recovery_timer.expires = jiffies +
+			msecs_to_jiffies(COMP_MODE_RCVRY_MSECS);
+
+	set_timer_slack(&xhci->comp_mode_recovery_timer,
+			msecs_to_jiffies(COMP_MODE_RCVRY_MSECS));
+	add_timer(&xhci->comp_mode_recovery_timer);
+	xhci_dbg(xhci, "Compliance Mode Recovery Timer Initialized.\n");
+}
+
+/*
+ * This function identifies the systems that have installed the SN65LVPE502CP
+ * USB3.0 re-driver and that need the Compliance Mode Quirk.
+ * Systems:
+ * Vendor: Hewlett-Packard -> System Models: Z420, Z620 and Z820
+ */
+static bool compliance_mode_recovery_timer_quirk_check(void)
+{
+	const char *dmi_product_name, *dmi_sys_vendor;
+
+	dmi_product_name = dmi_get_system_info(DMI_PRODUCT_NAME);
+	dmi_sys_vendor = dmi_get_system_info(DMI_SYS_VENDOR);
+
+	if (!(strstr(dmi_sys_vendor, "Hewlett-Packard")))
+		return false;
+
+	if (strstr(dmi_product_name, "Z420") ||
+			strstr(dmi_product_name, "Z620") ||
+			strstr(dmi_product_name, "Z820"))
+		return true;
+
+	return false;
+}
+
+static int xhci_all_ports_seen_u0(struct xhci_hcd *xhci)
+{
+	return (xhci->port_status_u0 == ((1 << xhci->num_usb3_ports)-1));
+}
+
+
 /*
  * Initialize memory for HCD and xHC (one-time init).
  *
@@ -421,6 +511,12 @@
 	retval = xhci_mem_init(xhci, GFP_KERNEL);
 	xhci_dbg(xhci, "Finished xhci_init\n");
 
+	/* Initializing Compliance Mode Recovery Data If Needed */
+	if (compliance_mode_recovery_timer_quirk_check()) {
+		xhci->quirks |= XHCI_COMP_MODE_QUIRK;
+		compliance_mode_recovery_timer_init(xhci);
+	}
+
 	return retval;
 }
 
@@ -629,6 +725,11 @@
 	del_timer_sync(&xhci->event_ring_timer);
 #endif
 
+	/* Deleting Compliance Mode Recovery Timer */
+	if ((xhci->quirks & XHCI_COMP_MODE_QUIRK) &&
+			(!(xhci_all_ports_seen_u0(xhci))))
+		del_timer_sync(&xhci->comp_mode_recovery_timer);
+
 	if (xhci->quirks & XHCI_AMD_PLL_FIX)
 		usb_amd_dev_put();
 
@@ -659,7 +760,7 @@
 {
 	struct xhci_hcd *xhci = hcd_to_xhci(hcd);
 
-	if (xhci->quirks && XHCI_SPURIOUS_REBOOT)
+	if (xhci->quirks & XHCI_SPURIOUS_REBOOT)
 		usb_disable_xhci_ports(to_pci_dev(hcd->self.controller));
 
 	spin_lock_irq(&xhci->lock);
@@ -806,6 +907,16 @@
 	}
 	spin_unlock_irq(&xhci->lock);
 
+	/*
+	 * Deleting Compliance Mode Recovery Timer because the xHCI Host
+	 * is about to be suspended.
+	 */
+	if ((xhci->quirks & XHCI_COMP_MODE_QUIRK) &&
+			(!(xhci_all_ports_seen_u0(xhci)))) {
+		del_timer_sync(&xhci->comp_mode_recovery_timer);
+		xhci_dbg(xhci, "Compliance Mode Recovery Timer Deleted!\n");
+	}
+
 	/* step 5: remove core well power */
 	/* synchronize irq when using MSI-X */
 	xhci_msix_sync_irqs(xhci);
@@ -938,6 +1049,16 @@
 		usb_hcd_resume_root_hub(hcd);
 		usb_hcd_resume_root_hub(xhci->shared_hcd);
 	}
+
+	/*
+	 * If system is subject to the Quirk, Compliance Mode Timer needs to
+	 * be re-initialized Always after a system resume. Ports are subject
+	 * to suffer the Compliance Mode issue again. It doesn't matter if
+	 * ports have entered previously to U0 before system's suspension.
+	 */
+	if (xhci->quirks & XHCI_COMP_MODE_QUIRK)
+		compliance_mode_recovery_timer_init(xhci);
+
 	return retval;
 }
 #endif	/* CONFIG_PM */
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index c713256..1a05908 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -1495,6 +1495,7 @@
 #define XHCI_LPM_SUPPORT	(1 << 11)
 #define XHCI_INTEL_HOST		(1 << 12)
 #define XHCI_SPURIOUS_REBOOT	(1 << 13)
+#define XHCI_COMP_MODE_QUIRK	(1 << 14)
 	unsigned int		num_active_eps;
 	unsigned int		limit_active_eps;
 	/* There are two roothubs to keep track of bus suspend info for */
@@ -1511,6 +1512,11 @@
 	unsigned		sw_lpm_support:1;
 	/* support xHCI 1.0 spec USB2 hardware LPM */
 	unsigned		hw_lpm_support:1;
+	/* Compliance Mode Recovery Data */
+	struct timer_list	comp_mode_recovery_timer;
+	u32			port_status_u0;
+/* Compliance Mode Timer Triggered every 2 seconds */
+#define COMP_MODE_RCVRY_MSECS 2000
 };
 
 /* convert between an HCD pointer and the corresponding EHCI_HCD */
diff --git a/drivers/usb/musb/musb_host.c b/drivers/usb/musb/musb_host.c
index 4bb717d..1ae378d5 100644
--- a/drivers/usb/musb/musb_host.c
+++ b/drivers/usb/musb/musb_host.c
@@ -2049,7 +2049,7 @@
 	 * we only have work to do in the former case.
 	 */
 	spin_lock_irqsave(&musb->lock, flags);
-	if (hep->hcpriv) {
+	if (hep->hcpriv || !next_urb(qh)) {
 		/* some concurrent activity submitted another urb to hep...
 		 * odd, rare, error prone, but legal.
 		 */
diff --git a/drivers/usb/musb/musbhsdma.c b/drivers/usb/musb/musbhsdma.c
index 57a6085..c1be687 100644
--- a/drivers/usb/musb/musbhsdma.c
+++ b/drivers/usb/musb/musbhsdma.c
@@ -388,7 +388,7 @@
 	struct platform_device *pdev = to_platform_device(dev);
 	int irq = platform_get_irq_byname(pdev, "dma");
 
-	if (irq == 0) {
+	if (irq <= 0) {
 		dev_err(dev, "No DMA interrupt line!\n");
 		return NULL;
 	}
diff --git a/drivers/usb/musb/tusb6010.c b/drivers/usb/musb/tusb6010.c
index 1a1bd9c..3416254 100644
--- a/drivers/usb/musb/tusb6010.c
+++ b/drivers/usb/musb/tusb6010.c
@@ -1215,7 +1215,7 @@
 	ret = platform_device_add(musb);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to register musb device\n");
-		goto err1;
+		goto err2;
 	}
 
 	return 0;
diff --git a/drivers/usb/renesas_usbhs/fifo.c b/drivers/usb/renesas_usbhs/fifo.c
index ecd1730..143c4e9 100644
--- a/drivers/usb/renesas_usbhs/fifo.c
+++ b/drivers/usb/renesas_usbhs/fifo.c
@@ -818,7 +818,7 @@
 	    usbhs_pipe_is_dcp(pipe))
 		goto usbhsf_pio_prepare_push;
 
-	if (len % 4) /* 32bit alignment */
+	if (len & 0x7) /* 8byte alignment */
 		goto usbhsf_pio_prepare_push;
 
 	if ((uintptr_t)(pkt->buf + pkt->actual) & 0x7) /* 8byte alignment */
@@ -905,7 +905,7 @@
 	/* use PIO if packet is less than pio_dma_border */
 	len = usbhsf_fifo_rcv_len(priv, fifo);
 	len = min(pkt->length - pkt->actual, len);
-	if (len % 4) /* 32bit alignment */
+	if (len & 0x7) /* 8byte alignment */
 		goto usbhsf_pio_prepare_pop_unselect;
 
 	if (len < usbhs_get_dparam(priv, pio_dma_border))
diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index 5620db6..f906b3a 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -704,6 +704,7 @@
 	{ USB_DEVICE(FTDI_VID, FTDI_PCDJ_DAC2_PID) },
 	{ USB_DEVICE(FTDI_VID, FTDI_RRCIRKITS_LOCOBUFFER_PID) },
 	{ USB_DEVICE(FTDI_VID, FTDI_ASK_RDR400_PID) },
+	{ USB_DEVICE(FTDI_VID, FTDI_NZR_SEM_USB_PID) },
 	{ USB_DEVICE(ICOM_VID, ICOM_ID_1_PID) },
 	{ USB_DEVICE(ICOM_VID, ICOM_OPC_U_UC_PID) },
 	{ USB_DEVICE(ICOM_VID, ICOM_ID_RP2C1_PID) },
@@ -804,13 +805,32 @@
 		.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
 	{ USB_DEVICE(ADI_VID, ADI_GNICEPLUS_PID),
 		.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
-	{ USB_DEVICE(MICROCHIP_VID, MICROCHIP_USB_BOARD_PID) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(MICROCHIP_VID, MICROCHIP_USB_BOARD_PID,
+					USB_CLASS_VENDOR_SPEC,
+					USB_SUBCLASS_VENDOR_SPEC, 0x00) },
 	{ USB_DEVICE(JETI_VID, JETI_SPC1201_PID) },
 	{ USB_DEVICE(MARVELL_VID, MARVELL_SHEEVAPLUG_PID),
 		.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
 	{ USB_DEVICE(LARSENBRUSGAARD_VID, LB_ALTITRACK_PID) },
 	{ USB_DEVICE(GN_OTOMETRICS_VID, AURICAL_USB_PID) },
+	{ USB_DEVICE(FTDI_VID, PI_C865_PID) },
+	{ USB_DEVICE(FTDI_VID, PI_C857_PID) },
+	{ USB_DEVICE(PI_VID, PI_C866_PID) },
+	{ USB_DEVICE(PI_VID, PI_C663_PID) },
+	{ USB_DEVICE(PI_VID, PI_C725_PID) },
+	{ USB_DEVICE(PI_VID, PI_E517_PID) },
+	{ USB_DEVICE(PI_VID, PI_C863_PID) },
 	{ USB_DEVICE(PI_VID, PI_E861_PID) },
+	{ USB_DEVICE(PI_VID, PI_C867_PID) },
+	{ USB_DEVICE(PI_VID, PI_E609_PID) },
+	{ USB_DEVICE(PI_VID, PI_E709_PID) },
+	{ USB_DEVICE(PI_VID, PI_100F_PID) },
+	{ USB_DEVICE(PI_VID, PI_1011_PID) },
+	{ USB_DEVICE(PI_VID, PI_1012_PID) },
+	{ USB_DEVICE(PI_VID, PI_1013_PID) },
+	{ USB_DEVICE(PI_VID, PI_1014_PID) },
+	{ USB_DEVICE(PI_VID, PI_1015_PID) },
+	{ USB_DEVICE(PI_VID, PI_1016_PID) },
 	{ USB_DEVICE(KONDO_VID, KONDO_USB_SERIAL_PID) },
 	{ USB_DEVICE(BAYER_VID, BAYER_CONTOUR_CABLE_PID) },
 	{ USB_DEVICE(FTDI_VID, MARVELL_OPENRD_PID),
diff --git a/drivers/usb/serial/ftdi_sio_ids.h b/drivers/usb/serial/ftdi_sio_ids.h
index 5dd96ca..41fe582 100644
--- a/drivers/usb/serial/ftdi_sio_ids.h
+++ b/drivers/usb/serial/ftdi_sio_ids.h
@@ -75,6 +75,9 @@
 #define FTDI_OPENDCC_GATEWAY_PID	0xBFDB
 #define FTDI_OPENDCC_GBM_PID	0xBFDC
 
+/* NZR SEM 16+ USB (http://www.nzr.de) */
+#define FTDI_NZR_SEM_USB_PID	0xC1E0	/* NZR SEM-LOG16+ */
+
 /*
  * RR-CirKits LocoBuffer USB (http://www.rr-cirkits.com)
  */
@@ -539,7 +542,10 @@
 /*
  * Microchip Technology, Inc.
  *
- * MICROCHIP_VID (0x04D8) and MICROCHIP_USB_BOARD_PID (0x000A) are also used by:
+ * MICROCHIP_VID (0x04D8) and MICROCHIP_USB_BOARD_PID (0x000A) are
+ * used by single function CDC ACM class based firmware demo
+ * applications.  The VID/PID has also been used in firmware
+ * emulating FTDI serial chips by:
  * Hornby Elite - Digital Command Control Console
  * http://www.hornby.com/hornby-dcc/controllers/
  */
@@ -791,8 +797,27 @@
  * Physik Instrumente
  * http://www.physikinstrumente.com/en/products/
  */
+/* These two devices use the VID of FTDI */
+#define PI_C865_PID	0xe0a0  /* PI C-865 Piezomotor Controller */
+#define PI_C857_PID	0xe0a1  /* PI Encoder Trigger Box */
+
 #define PI_VID              0x1a72  /* Vendor ID */
-#define PI_E861_PID         0x1008  /* E-861 piezo controller USB connection */
+#define PI_C866_PID	0x1000  /* PI C-866 Piezomotor Controller */
+#define PI_C663_PID	0x1001  /* PI C-663 Mercury-Step */
+#define PI_C725_PID	0x1002  /* PI C-725 Piezomotor Controller */
+#define PI_E517_PID	0x1005  /* PI E-517 Digital Piezo Controller Operation Module */
+#define PI_C863_PID	0x1007  /* PI C-863 */
+#define PI_E861_PID	0x1008  /* PI E-861 Piezomotor Controller */
+#define PI_C867_PID	0x1009  /* PI C-867 Piezomotor Controller */
+#define PI_E609_PID	0x100D  /* PI E-609 Digital Piezo Controller */
+#define PI_E709_PID	0x100E  /* PI E-709 Digital Piezo Controller */
+#define PI_100F_PID	0x100F  /* PI Digital Piezo Controller */
+#define PI_1011_PID	0x1011  /* PI Digital Piezo Controller */
+#define PI_1012_PID	0x1012  /* PI Motion Controller */
+#define PI_1013_PID	0x1013  /* PI Motion Controller */
+#define PI_1014_PID	0x1014  /* PI Device */
+#define PI_1015_PID	0x1015  /* PI Device */
+#define PI_1016_PID	0x1016  /* PI Digital Servo Module */
 
 /*
  * Kondo Kagaku Co.Ltd.
diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index cc40f47..5ce88d1 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -886,8 +886,6 @@
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1010, 0xff, 0xff, 0xff),
 	  .driver_info = (kernel_ulong_t)&net_intf4_blacklist },
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1012, 0xff, 0xff, 0xff) },
-	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1018, 0xff, 0xff, 0xff),
-	  .driver_info = (kernel_ulong_t)&net_intf3_blacklist },
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1057, 0xff, 0xff, 0xff) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1058, 0xff, 0xff, 0xff) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0x1059, 0xff, 0xff, 0xff) },
@@ -1092,6 +1090,10 @@
 	 .driver_info = (kernel_ulong_t)&zte_ad3812_z_blacklist },
 	{ USB_DEVICE_AND_INTERFACE_INFO(ZTE_VENDOR_ID, ZTE_PRODUCT_MC2716, 0xff, 0xff, 0xff),
 	 .driver_info = (kernel_ulong_t)&zte_mc2716_z_blacklist },
+	{ USB_VENDOR_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff, 0x02, 0x01) },
+	{ USB_VENDOR_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff, 0x02, 0x05) },
+	{ USB_VENDOR_AND_INTERFACE_INFO(ZTE_VENDOR_ID, 0xff, 0x86, 0x10) },
+
 	{ USB_DEVICE(BENQ_VENDOR_ID, BENQ_PRODUCT_H10) },
 	{ USB_DEVICE(DLINK_VENDOR_ID, DLINK_PRODUCT_DWM_652) },
 	{ USB_DEVICE(ALINK_VENDOR_ID, DLINK_PRODUCT_DWM_652_U5) }, /* Yes, ALINK_VENDOR_ID */
diff --git a/drivers/video/auo_k190x.c b/drivers/video/auo_k190x.c
index 77da6a2..c03ecdd 100644
--- a/drivers/video/auo_k190x.c
+++ b/drivers/video/auo_k190x.c
@@ -987,7 +987,6 @@
 	fb_dealloc_cmap(&info->cmap);
 err_cmap:
 	fb_deferred_io_cleanup(info);
-	kfree(info->fbdefio);
 err_defio:
 	vfree((void *)info->screen_base);
 err_irq:
@@ -1022,7 +1021,6 @@
 	fb_dealloc_cmap(&info->cmap);
 
 	fb_deferred_io_cleanup(info);
-	kfree(info->fbdefio);
 
 	vfree((void *)info->screen_base);
 
diff --git a/drivers/video/console/bitblit.c b/drivers/video/console/bitblit.c
index 28b1a83..61b182b 100644
--- a/drivers/video/console/bitblit.c
+++ b/drivers/video/console/bitblit.c
@@ -162,7 +162,7 @@
 	image.depth = 1;
 
 	if (attribute) {
-		buf = kmalloc(cellsize, GFP_KERNEL);
+		buf = kmalloc(cellsize, GFP_ATOMIC);
 		if (!buf)
 			return;
 	}
diff --git a/drivers/video/console/fbcon.c b/drivers/video/console/fbcon.c
index 88e9204..fdefa8f 100644
--- a/drivers/video/console/fbcon.c
+++ b/drivers/video/console/fbcon.c
@@ -449,7 +449,7 @@
 
 	while ((options = strsep(&this_opt, ",")) != NULL) {
 		if (!strncmp(options, "font:", 5))
-			strcpy(fontname, options + 5);
+			strlcpy(fontname, options + 5, sizeof(fontname));
 		
 		if (!strncmp(options, "scrollback:", 11)) {
 			options += 11;
diff --git a/drivers/video/mb862xx/mb862xxfbdrv.c b/drivers/video/mb862xx/mb862xxfbdrv.c
index 00ce1f3..57d940b 100644
--- a/drivers/video/mb862xx/mb862xxfbdrv.c
+++ b/drivers/video/mb862xx/mb862xxfbdrv.c
@@ -328,6 +328,8 @@
 	case MB862XX_L1_SET_CFG:
 		if (copy_from_user(l1_cfg, argp, sizeof(*l1_cfg)))
 			return -EFAULT;
+		if (l1_cfg->dh == 0 || l1_cfg->dw == 0)
+			return -EINVAL;
 		if ((l1_cfg->sw >= l1_cfg->dw) && (l1_cfg->sh >= l1_cfg->dh)) {
 			/* downscaling */
 			outreg(cap, GC_CAP_CSC,
diff --git a/drivers/video/omap2/dss/sdi.c b/drivers/video/omap2/dss/sdi.c
index 5d31699..f43bfe1 100644
--- a/drivers/video/omap2/dss/sdi.c
+++ b/drivers/video/omap2/dss/sdi.c
@@ -105,6 +105,20 @@
 
 	sdi_config_lcd_manager(dssdev);
 
+	/*
+	 * LCLK and PCLK divisors are located in shadow registers, and we
+	 * normally write them to DISPC registers when enabling the output.
+	 * However, SDI uses pck-free as source clock for its PLL, and pck-free
+	 * is affected by the divisors. And as we need the PLL before enabling
+	 * the output, we need to write the divisors early.
+	 *
+	 * It seems just writing to the DISPC register is enough, and we don't
+	 * need to care about the shadow register mechanism for pck-free. The
+	 * exact reason for this is unknown.
+	 */
+	dispc_mgr_set_clock_div(dssdev->manager->id,
+			&sdi.mgr_config.clock_info);
+
 	dss_sdi_init(dssdev->phy.sdi.datapairs);
 	r = dss_sdi_enable();
 	if (r)
diff --git a/drivers/video/omap2/omapfb/omapfb-main.c b/drivers/video/omap2/omapfb/omapfb-main.c
index 08ec1a7..fc671d3 100644
--- a/drivers/video/omap2/omapfb/omapfb-main.c
+++ b/drivers/video/omap2/omapfb/omapfb-main.c
@@ -1192,7 +1192,7 @@
 			break;
 
 		if (regno < 16) {
-			u16 pal;
+			u32 pal;
 			pal = ((red >> (16 - var->red.length)) <<
 					var->red.offset) |
 				((green >> (16 - var->green.length)) <<
diff --git a/drivers/xen/swiotlb-xen.c b/drivers/xen/swiotlb-xen.c
index 1afb4fb..4d51948 100644
--- a/drivers/xen/swiotlb-xen.c
+++ b/drivers/xen/swiotlb-xen.c
@@ -232,7 +232,7 @@
 		return ret;
 
 	if (hwdev && hwdev->coherent_dma_mask)
-		dma_mask = hwdev->coherent_dma_mask;
+		dma_mask = dma_alloc_coherent_mask(hwdev, flags);
 
 	phys = virt_to_phys(ret);
 	dev_addr = xen_phys_to_bus(phys);
diff --git a/drivers/xen/xen-pciback/pci_stub.c b/drivers/xen/xen-pciback/pci_stub.c
index 097e536..0334272 100644
--- a/drivers/xen/xen-pciback/pci_stub.c
+++ b/drivers/xen/xen-pciback/pci_stub.c
@@ -353,16 +353,16 @@
 	if (err)
 		goto config_release;
 
-	dev_dbg(&dev->dev, "reseting (FLR, D3, etc) the device\n");
-	__pci_reset_function_locked(dev);
-
 	/* We need the device active to save the state. */
 	dev_dbg(&dev->dev, "save state of device\n");
 	pci_save_state(dev);
 	dev_data->pci_saved_state = pci_store_saved_state(dev);
 	if (!dev_data->pci_saved_state)
 		dev_err(&dev->dev, "Could not store PCI conf saved state!\n");
-
+	else {
+		dev_dbg(&dev->dev, "reseting (FLR, D3, etc) the device\n");
+		__pci_reset_function_locked(dev);
+	}
 	/* Now disable the device (this also ensures some private device
 	 * data is setup before we export)
 	 */
diff --git a/fs/cifs/file.c b/fs/cifs/file.c
index 9154192..71e9ad9 100644
--- a/fs/cifs/file.c
+++ b/fs/cifs/file.c
@@ -917,7 +917,7 @@
 	if (!buf) {
 		mutex_unlock(&cinode->lock_mutex);
 		free_xid(xid);
-		return rc;
+		return -ENOMEM;
 	}
 
 	for (i = 0; i < 2; i++) {
diff --git a/fs/cifs/smb2pdu.h b/fs/cifs/smb2pdu.h
index c5fbfac..15dc8ee 100644
--- a/fs/cifs/smb2pdu.h
+++ b/fs/cifs/smb2pdu.h
@@ -96,7 +96,7 @@
  *
  */
 
-#define SMB2_HEADER_STRUCTURE_SIZE __constant_le16_to_cpu(64)
+#define SMB2_HEADER_STRUCTURE_SIZE __constant_cpu_to_le16(64)
 
 struct smb2_hdr {
 	__be32 smb2_buf_length;	/* big endian on wire */
@@ -140,7 +140,7 @@
  *
  */
 
-#define SMB2_ERROR_STRUCTURE_SIZE2 __constant_le16_to_cpu(9)
+#define SMB2_ERROR_STRUCTURE_SIZE2 __constant_cpu_to_le16(9)
 
 struct smb2_err_rsp {
 	struct smb2_hdr hdr;
diff --git a/fs/ecryptfs/file.c b/fs/ecryptfs/file.c
index 44ce5c6..d45ba45 100644
--- a/fs/ecryptfs/file.c
+++ b/fs/ecryptfs/file.c
@@ -275,8 +275,14 @@
 
 static int ecryptfs_flush(struct file *file, fl_owner_t td)
 {
-	return file->f_mode & FMODE_WRITE
-	       ? filemap_write_and_wait(file->f_mapping) : 0;
+	struct file *lower_file = ecryptfs_file_to_lower(file);
+
+	if (lower_file->f_op && lower_file->f_op->flush) {
+		filemap_write_and_wait(file->f_mapping);
+		return lower_file->f_op->flush(lower_file, td);
+	}
+
+	return 0;
 }
 
 static int ecryptfs_release(struct inode *inode, struct file *file)
diff --git a/fs/ecryptfs/inode.c b/fs/ecryptfs/inode.c
index 534b129..cc7709e7 100644
--- a/fs/ecryptfs/inode.c
+++ b/fs/ecryptfs/inode.c
@@ -619,6 +619,7 @@
 	struct dentry *lower_old_dir_dentry;
 	struct dentry *lower_new_dir_dentry;
 	struct dentry *trap = NULL;
+	struct inode *target_inode;
 
 	lower_old_dentry = ecryptfs_dentry_to_lower(old_dentry);
 	lower_new_dentry = ecryptfs_dentry_to_lower(new_dentry);
@@ -626,6 +627,7 @@
 	dget(lower_new_dentry);
 	lower_old_dir_dentry = dget_parent(lower_old_dentry);
 	lower_new_dir_dentry = dget_parent(lower_new_dentry);
+	target_inode = new_dentry->d_inode;
 	trap = lock_rename(lower_old_dir_dentry, lower_new_dir_dentry);
 	/* source should not be ancestor of target */
 	if (trap == lower_old_dentry) {
@@ -641,6 +643,9 @@
 			lower_new_dir_dentry->d_inode, lower_new_dentry);
 	if (rc)
 		goto out_lock;
+	if (target_inode)
+		fsstack_copy_attr_all(target_inode,
+				      ecryptfs_inode_to_lower(target_inode));
 	fsstack_copy_attr_all(new_dir, lower_new_dir_dentry->d_inode);
 	if (new_dir != old_dir)
 		fsstack_copy_attr_all(old_dir, lower_old_dir_dentry->d_inode);
diff --git a/fs/ecryptfs/main.c b/fs/ecryptfs/main.c
index 2768138..9b627c1 100644
--- a/fs/ecryptfs/main.c
+++ b/fs/ecryptfs/main.c
@@ -162,6 +162,7 @@
 	inode_info = ecryptfs_inode_to_private(inode);
 	if (atomic_dec_and_mutex_lock(&inode_info->lower_file_count,
 				      &inode_info->lower_file_mutex)) {
+		filemap_write_and_wait(inode->i_mapping);
 		fput(inode_info->lower_file);
 		inode_info->lower_file = NULL;
 		mutex_unlock(&inode_info->lower_file_mutex);
diff --git a/fs/ext3/inode.c b/fs/ext3/inode.c
index a075973..ff574b4 100644
--- a/fs/ext3/inode.c
+++ b/fs/ext3/inode.c
@@ -3072,6 +3072,8 @@
 	struct ext3_inode_info *ei = EXT3_I(inode);
 	struct buffer_head *bh = iloc->bh;
 	int err = 0, rc, block;
+	int need_datasync = 0;
+	__le32 disksize;
 	uid_t i_uid;
 	gid_t i_gid;
 
@@ -3113,7 +3115,11 @@
 		raw_inode->i_gid_high = 0;
 	}
 	raw_inode->i_links_count = cpu_to_le16(inode->i_nlink);
-	raw_inode->i_size = cpu_to_le32(ei->i_disksize);
+	disksize = cpu_to_le32(ei->i_disksize);
+	if (disksize != raw_inode->i_size) {
+		need_datasync = 1;
+		raw_inode->i_size = disksize;
+	}
 	raw_inode->i_atime = cpu_to_le32(inode->i_atime.tv_sec);
 	raw_inode->i_ctime = cpu_to_le32(inode->i_ctime.tv_sec);
 	raw_inode->i_mtime = cpu_to_le32(inode->i_mtime.tv_sec);
@@ -3129,8 +3135,11 @@
 	if (!S_ISREG(inode->i_mode)) {
 		raw_inode->i_dir_acl = cpu_to_le32(ei->i_dir_acl);
 	} else {
-		raw_inode->i_size_high =
-			cpu_to_le32(ei->i_disksize >> 32);
+		disksize = cpu_to_le32(ei->i_disksize >> 32);
+		if (disksize != raw_inode->i_size_high) {
+			raw_inode->i_size_high = disksize;
+			need_datasync = 1;
+		}
 		if (ei->i_disksize > 0x7fffffffULL) {
 			struct super_block *sb = inode->i_sb;
 			if (!EXT3_HAS_RO_COMPAT_FEATURE(sb,
@@ -3183,6 +3192,8 @@
 	ext3_clear_inode_state(inode, EXT3_STATE_NEW);
 
 	atomic_set(&ei->i_sync_tid, handle->h_transaction->t_tid);
+	if (need_datasync)
+		atomic_set(&ei->i_datasync_tid, handle->h_transaction->t_tid);
 out_brelse:
 	brelse (bh);
 	ext3_std_error(inode->i_sb, err);
diff --git a/fs/fuse/control.c b/fs/fuse/control.c
index 03ff5b1..75a20c0 100644
--- a/fs/fuse/control.c
+++ b/fs/fuse/control.c
@@ -117,7 +117,7 @@
 					      const char __user *buf,
 					      size_t count, loff_t *ppos)
 {
-	unsigned val;
+	unsigned uninitialized_var(val);
 	ssize_t ret;
 
 	ret = fuse_conn_limit_write(file, buf, count, ppos, &val,
@@ -154,7 +154,7 @@
 						    const char __user *buf,
 						    size_t count, loff_t *ppos)
 {
-	unsigned val;
+	unsigned uninitialized_var(val);
 	ssize_t ret;
 
 	ret = fuse_conn_limit_write(file, buf, count, ppos, &val,
diff --git a/fs/fuse/cuse.c b/fs/fuse/cuse.c
index 3426521..ee8d550 100644
--- a/fs/fuse/cuse.c
+++ b/fs/fuse/cuse.c
@@ -396,7 +396,7 @@
 err_region:
 	unregister_chrdev_region(devt, 1);
 err:
-	fc->conn_error = 1;
+	fuse_conn_kill(fc);
 	goto out;
 }
 
@@ -532,8 +532,6 @@
 		cdev_del(cc->cdev);
 	}
 
-	/* kill connection and shutdown channel */
-	fuse_conn_kill(&cc->fc);
 	rc = fuse_dev_release(inode, file);	/* puts the base reference */
 
 	return rc;
diff --git a/fs/fuse/dev.c b/fs/fuse/dev.c
index 7df2b5e..f4246cf 100644
--- a/fs/fuse/dev.c
+++ b/fs/fuse/dev.c
@@ -1576,6 +1576,7 @@
 		req->pages[req->num_pages] = page;
 		req->num_pages++;
 
+		offset = 0;
 		num -= this_num;
 		total_len += this_num;
 		index++;
diff --git a/fs/fuse/inode.c b/fs/fuse/inode.c
index ce0a283..fca222d 100644
--- a/fs/fuse/inode.c
+++ b/fs/fuse/inode.c
@@ -367,11 +367,6 @@
 	wake_up_all(&fc->waitq);
 	wake_up_all(&fc->blocked_waitq);
 	wake_up_all(&fc->reserved_req_waitq);
-	mutex_lock(&fuse_mutex);
-	list_del(&fc->entry);
-	fuse_ctl_remove_conn(fc);
-	mutex_unlock(&fuse_mutex);
-	fuse_bdi_destroy(fc);
 }
 EXPORT_SYMBOL_GPL(fuse_conn_kill);
 
@@ -380,7 +375,14 @@
 	struct fuse_conn *fc = get_fuse_conn_super(sb);
 
 	fuse_send_destroy(fc);
+
 	fuse_conn_kill(fc);
+	mutex_lock(&fuse_mutex);
+	list_del(&fc->entry);
+	fuse_ctl_remove_conn(fc);
+	mutex_unlock(&fuse_mutex);
+	fuse_bdi_destroy(fc);
+
 	fuse_conn_put(fc);
 }
 
diff --git a/fs/gfs2/file.c b/fs/gfs2/file.c
index d1d791e..382000f 100644
--- a/fs/gfs2/file.c
+++ b/fs/gfs2/file.c
@@ -323,6 +323,29 @@
 }
 
 /**
+ * gfs2_size_hint - Give a hint to the size of a write request
+ * @file: The struct file
+ * @offset: The file offset of the write
+ * @size: The length of the write
+ *
+ * When we are about to do a write, this function records the total
+ * write size in order to provide a suitable hint to the lower layers
+ * about how many blocks will be required.
+ *
+ */
+
+static void gfs2_size_hint(struct file *filep, loff_t offset, size_t size)
+{
+	struct inode *inode = filep->f_dentry->d_inode;
+	struct gfs2_sbd *sdp = GFS2_SB(inode);
+	struct gfs2_inode *ip = GFS2_I(inode);
+	size_t blks = (size + sdp->sd_sb.sb_bsize - 1) >> sdp->sd_sb.sb_bsize_shift;
+	int hint = min_t(size_t, INT_MAX, blks);
+
+	atomic_set(&ip->i_res->rs_sizehint, hint);
+}
+
+/**
  * gfs2_allocate_page_backing - Use bmap to allocate blocks
  * @page: The (locked) page to allocate backing for
  *
@@ -382,8 +405,7 @@
 	if (ret)
 		return ret;
 
-	atomic_set(&ip->i_res->rs_sizehint,
-		   PAGE_CACHE_SIZE >> sdp->sd_sb.sb_bsize_shift);
+	gfs2_size_hint(vma->vm_file, pos, PAGE_CACHE_SIZE);
 
 	gfs2_holder_init(ip->i_gl, LM_ST_EXCLUSIVE, 0, &gh);
 	ret = gfs2_glock_nq(&gh);
@@ -663,7 +685,8 @@
 	if (ret)
 		return ret;
 
-	atomic_set(&ip->i_res->rs_sizehint, writesize >> sdp->sd_sb.sb_bsize_shift);
+	gfs2_size_hint(file, pos, writesize);
+
 	if (file->f_flags & O_APPEND) {
 		struct gfs2_holder gh;
 
@@ -789,7 +812,7 @@
 	if (unlikely(error))
 		goto out_uninit;
 
-	atomic_set(&ip->i_res->rs_sizehint, len >> sdp->sd_sb.sb_bsize_shift);
+	gfs2_size_hint(file, offset, len);
 
 	while (len > 0) {
 		if (len < bytes)
diff --git a/fs/gfs2/inode.c b/fs/gfs2/inode.c
index 4ce22e5..753af3d 100644
--- a/fs/gfs2/inode.c
+++ b/fs/gfs2/inode.c
@@ -1722,7 +1722,9 @@
 	gfs2_holder_init(ip->i_gl, LM_ST_EXCLUSIVE, 0, &gh);
 	ret = gfs2_glock_nq(&gh);
 	if (ret == 0) {
-		ret = generic_setxattr(dentry, name, data, size, flags);
+		ret = gfs2_rs_alloc(ip);
+		if (ret == 0)
+			ret = generic_setxattr(dentry, name, data, size, flags);
 		gfs2_glock_dq(&gh);
 	}
 	gfs2_holder_uninit(&gh);
@@ -1757,7 +1759,9 @@
 	gfs2_holder_init(ip->i_gl, LM_ST_EXCLUSIVE, 0, &gh);
 	ret = gfs2_glock_nq(&gh);
 	if (ret == 0) {
-		ret = generic_removexattr(dentry, name);
+		ret = gfs2_rs_alloc(ip);
+		if (ret == 0)
+			ret = generic_removexattr(dentry, name);
 		gfs2_glock_dq(&gh);
 	}
 	gfs2_holder_uninit(&gh);
diff --git a/fs/gfs2/rgrp.c b/fs/gfs2/rgrp.c
index 4d34887..c9ed814 100644
--- a/fs/gfs2/rgrp.c
+++ b/fs/gfs2/rgrp.c
@@ -1961,7 +1961,7 @@
  * @dinode: 1 if this block is a dinode block, otherwise data block
  * @nblocks: desired extent length
  *
- * Lay claim to previously allocated block reservation blocks.
+ * Lay claim to previously reserved blocks.
  * Returns: Starting block number of the blocks claimed.
  * Sets *nblocks to the actual extent length allocated.
  */
@@ -1970,19 +1970,17 @@
 {
 	struct gfs2_blkreserv *rs = ip->i_res;
 	struct gfs2_rgrpd *rgd = rs->rs_rgd;
-	struct gfs2_sbd *sdp = GFS2_SB(&ip->i_inode);
 	struct gfs2_bitmap *bi;
 	u64 start_block = gfs2_rs_startblk(rs);
 	const unsigned int elen = *nblocks;
 
-	/*BUG_ON(!gfs2_glock_is_locked_by_me(ip->i_gl));*/
-	gfs2_assert_withdraw(sdp, rgd);
-	/*BUG_ON(!gfs2_glock_is_locked_by_me(rgd->rd_gl));*/
 	bi = rs->rs_bi;
 	gfs2_trans_add_bh(rgd->rd_gl, bi->bi_bh, 1);
 
 	for (*nblocks = 0; *nblocks < elen && rs->rs_free; (*nblocks)++) {
-		/* Make sure the bitmap hasn't changed */
+		if (gfs2_testbit(rgd, bi->bi_bh->b_data + bi->bi_offset,
+				 bi->bi_len, rs->rs_biblk) != GFS2_BLKST_FREE)
+			break;
 		gfs2_setbit(rgd, bi->bi_clone, bi, rs->rs_biblk,
 			    dinode ? GFS2_BLKST_DINODE : GFS2_BLKST_USED);
 		rs->rs_biblk++;
@@ -1991,20 +1989,12 @@
 		BUG_ON(!rgd->rd_reserved);
 		rgd->rd_reserved--;
 		dinode = false;
-		trace_gfs2_rs(ip, rs, TRACE_RS_CLAIM);
 	}
 
-	if (!rs->rs_free) {
-		struct gfs2_rgrpd *rgd = ip->i_res->rs_rgd;
-
+	trace_gfs2_rs(ip, rs, TRACE_RS_CLAIM);
+	if (!rs->rs_free || *nblocks != elen)
 		gfs2_rs_deltree(rs);
-		/* -nblocks because we haven't returned to do the math yet.
-		   I'm doing the math backwards to prevent negative numbers,
-		   but think of it as:
-		   if (unclaimed_blocks(rgd) - *nblocks >= RGRP_RSRV_MINBLKS */
-		if (unclaimed_blocks(rgd) >= RGRP_RSRV_MINBLKS + *nblocks)
-			rg_mblk_search(rgd, ip);
-	}
+
 	return start_block;
 }
 
@@ -2037,34 +2027,34 @@
 	if (ip->i_res->rs_requested == 0)
 		return -ECANCELED;
 
-	/* Check if we have a multi-block reservation, and if so, claim the
-	   next free block from it. */
+	/* If we have a reservation, claim blocks from it. */
 	if (gfs2_rs_active(ip->i_res)) {
 		BUG_ON(!ip->i_res->rs_free);
 		rgd = ip->i_res->rs_rgd;
 		block = claim_reserved_blks(ip, dinode, nblocks);
-	} else {
-		rgd = ip->i_rgd;
-
-		if (!dinode && rgrp_contains_block(rgd, ip->i_goal))
-			goal = ip->i_goal - rgd->rd_data0;
-		else
-			goal = rgd->rd_last_alloc;
-
-		blk = rgblk_search(rgd, goal, GFS2_BLKST_FREE, &bi);
-
-		/* Since all blocks are reserved in advance, this shouldn't
-		   happen */
-		if (blk == BFITNOENT) {
-			printk(KERN_WARNING "BFITNOENT, nblocks=%u\n",
-			       *nblocks);
-			printk(KERN_WARNING "FULL=%d\n",
-			       test_bit(GBF_FULL, &rgd->rd_bits->bi_flags));
-			goto rgrp_error;
-		}
-
-		block = gfs2_alloc_extent(rgd, bi, blk, dinode, nblocks);
+		if (*nblocks)
+			goto found_blocks;
 	}
+
+	rgd = ip->i_rgd;
+
+	if (!dinode && rgrp_contains_block(rgd, ip->i_goal))
+		goal = ip->i_goal - rgd->rd_data0;
+	else
+		goal = rgd->rd_last_alloc;
+
+	blk = rgblk_search(rgd, goal, GFS2_BLKST_FREE, &bi);
+
+	/* Since all blocks are reserved in advance, this shouldn't happen */
+	if (blk == BFITNOENT) {
+		printk(KERN_WARNING "BFITNOENT, nblocks=%u\n", *nblocks);
+		printk(KERN_WARNING "FULL=%d\n",
+		       test_bit(GBF_FULL, &rgd->rd_bits->bi_flags));
+		goto rgrp_error;
+	}
+
+	block = gfs2_alloc_extent(rgd, bi, blk, dinode, nblocks);
+found_blocks:
 	ndata = *nblocks;
 	if (dinode)
 		ndata--;
diff --git a/fs/nfs/file.c b/fs/nfs/file.c
index 75d6d0a..6a7fcab 100644
--- a/fs/nfs/file.c
+++ b/fs/nfs/file.c
@@ -287,10 +287,12 @@
 	struct inode *inode = file->f_path.dentry->d_inode;
 
 	ret = filemap_write_and_wait_range(inode->i_mapping, start, end);
+	if (ret != 0)
+		goto out;
 	mutex_lock(&inode->i_mutex);
 	ret = nfs_file_fsync_commit(file, start, end, datasync);
 	mutex_unlock(&inode->i_mutex);
-
+out:
 	return ret;
 }
 
diff --git a/fs/nfs/inode.c b/fs/nfs/inode.c
index c6e895f..9b47610 100644
--- a/fs/nfs/inode.c
+++ b/fs/nfs/inode.c
@@ -154,7 +154,7 @@
 	nfsi->attrtimeo = NFS_MINATTRTIMEO(inode);
 	nfsi->attrtimeo_timestamp = jiffies;
 
-	memset(NFS_COOKIEVERF(inode), 0, sizeof(NFS_COOKIEVERF(inode)));
+	memset(NFS_I(inode)->cookieverf, 0, sizeof(NFS_I(inode)->cookieverf));
 	if (S_ISREG(mode) || S_ISDIR(mode) || S_ISLNK(mode))
 		nfsi->cache_validity |= NFS_INO_INVALID_ATTR|NFS_INO_INVALID_DATA|NFS_INO_INVALID_ACCESS|NFS_INO_INVALID_ACL|NFS_INO_REVAL_PAGECACHE;
 	else
diff --git a/fs/nfs/nfs3proc.c b/fs/nfs/nfs3proc.c
index d6b3b5f..6932209 100644
--- a/fs/nfs/nfs3proc.c
+++ b/fs/nfs/nfs3proc.c
@@ -643,7 +643,7 @@
 		  u64 cookie, struct page **pages, unsigned int count, int plus)
 {
 	struct inode		*dir = dentry->d_inode;
-	__be32			*verf = NFS_COOKIEVERF(dir);
+	__be32			*verf = NFS_I(dir)->cookieverf;
 	struct nfs3_readdirargs	arg = {
 		.fh		= NFS_FH(dir),
 		.cookie		= cookie,
diff --git a/fs/nfs/nfs4file.c b/fs/nfs/nfs4file.c
index acb65e7..eb5eb8e 100644
--- a/fs/nfs/nfs4file.c
+++ b/fs/nfs/nfs4file.c
@@ -96,13 +96,15 @@
 	struct inode *inode = file->f_path.dentry->d_inode;
 
 	ret = filemap_write_and_wait_range(inode->i_mapping, start, end);
+	if (ret != 0)
+		goto out;
 	mutex_lock(&inode->i_mutex);
 	ret = nfs_file_fsync_commit(file, start, end, datasync);
 	if (!ret && !datasync)
 		/* application has asked for meta-data sync */
 		ret = pnfs_layoutcommit_inode(inode, true);
 	mutex_unlock(&inode->i_mutex);
-
+out:
 	return ret;
 }
 
diff --git a/fs/nfs/nfs4proc.c b/fs/nfs/nfs4proc.c
index 6352741..1e50326 100644
--- a/fs/nfs/nfs4proc.c
+++ b/fs/nfs/nfs4proc.c
@@ -3215,11 +3215,11 @@
 			dentry->d_parent->d_name.name,
 			dentry->d_name.name,
 			(unsigned long long)cookie);
-	nfs4_setup_readdir(cookie, NFS_COOKIEVERF(dir), dentry, &args);
+	nfs4_setup_readdir(cookie, NFS_I(dir)->cookieverf, dentry, &args);
 	res.pgbase = args.pgbase;
 	status = nfs4_call_sync(NFS_SERVER(dir)->client, NFS_SERVER(dir), &msg, &args.seq_args, &res.seq_res, 0);
 	if (status >= 0) {
-		memcpy(NFS_COOKIEVERF(dir), res.verifier.data, NFS4_VERIFIER_SIZE);
+		memcpy(NFS_I(dir)->cookieverf, res.verifier.data, NFS4_VERIFIER_SIZE);
 		status += args.pgbase;
 	}
 
@@ -3653,11 +3653,11 @@
 		&& (server->acl_bitmask & ACL4_SUPPORT_DENY_ACL);
 }
 
-/* Assuming that XATTR_SIZE_MAX is a multiple of PAGE_CACHE_SIZE, and that
- * it's OK to put sizeof(void) * (XATTR_SIZE_MAX/PAGE_CACHE_SIZE) bytes on
+/* Assuming that XATTR_SIZE_MAX is a multiple of PAGE_SIZE, and that
+ * it's OK to put sizeof(void) * (XATTR_SIZE_MAX/PAGE_SIZE) bytes on
  * the stack.
  */
-#define NFS4ACL_MAXPAGES (XATTR_SIZE_MAX >> PAGE_CACHE_SHIFT)
+#define NFS4ACL_MAXPAGES DIV_ROUND_UP(XATTR_SIZE_MAX, PAGE_SIZE)
 
 static int buf_to_pages_noslab(const void *buf, size_t buflen,
 		struct page **pages, unsigned int *pgbase)
@@ -3668,7 +3668,7 @@
 	spages = pages;
 
 	do {
-		len = min_t(size_t, PAGE_CACHE_SIZE, buflen);
+		len = min_t(size_t, PAGE_SIZE, buflen);
 		newpage = alloc_page(GFP_KERNEL);
 
 		if (newpage == NULL)
@@ -3739,7 +3739,7 @@
 	struct nfs4_cached_acl *acl;
 	size_t buflen = sizeof(*acl) + acl_len;
 
-	if (pages && buflen <= PAGE_SIZE) {
+	if (buflen <= PAGE_SIZE) {
 		acl = kmalloc(buflen, GFP_KERNEL);
 		if (acl == NULL)
 			goto out;
@@ -3782,17 +3782,15 @@
 		.rpc_argp = &args,
 		.rpc_resp = &res,
 	};
-	int ret = -ENOMEM, npages, i;
-	size_t acl_len = 0;
+	unsigned int npages = DIV_ROUND_UP(buflen, PAGE_SIZE);
+	int ret = -ENOMEM, i;
 
-	npages = (buflen + PAGE_SIZE - 1) >> PAGE_SHIFT;
 	/* As long as we're doing a round trip to the server anyway,
 	 * let's be prepared for a page of acl data. */
 	if (npages == 0)
 		npages = 1;
-
-	/* Add an extra page to handle the bitmap returned */
-	npages++;
+	if (npages > ARRAY_SIZE(pages))
+		return -ERANGE;
 
 	for (i = 0; i < npages; i++) {
 		pages[i] = alloc_page(GFP_KERNEL);
@@ -3808,11 +3806,6 @@
 	args.acl_len = npages * PAGE_SIZE;
 	args.acl_pgbase = 0;
 
-	/* Let decode_getfacl know not to fail if the ACL data is larger than
-	 * the page we send as a guess */
-	if (buf == NULL)
-		res.acl_flags |= NFS4_ACL_LEN_REQUEST;
-
 	dprintk("%s  buf %p buflen %zu npages %d args.acl_len %zu\n",
 		__func__, buf, buflen, npages, args.acl_len);
 	ret = nfs4_call_sync(NFS_SERVER(inode)->client, NFS_SERVER(inode),
@@ -3820,20 +3813,19 @@
 	if (ret)
 		goto out_free;
 
-	acl_len = res.acl_len;
-	if (acl_len > args.acl_len)
-		nfs4_write_cached_acl(inode, NULL, 0, acl_len);
-	else
-		nfs4_write_cached_acl(inode, pages, res.acl_data_offset,
-				      acl_len);
-	if (buf) {
+	/* Handle the case where the passed-in buffer is too short */
+	if (res.acl_flags & NFS4_ACL_TRUNC) {
+		/* Did the user only issue a request for the acl length? */
+		if (buf == NULL)
+			goto out_ok;
 		ret = -ERANGE;
-		if (acl_len > buflen)
-			goto out_free;
-		_copy_from_pages(buf, pages, res.acl_data_offset,
-				acl_len);
+		goto out_free;
 	}
-	ret = acl_len;
+	nfs4_write_cached_acl(inode, pages, res.acl_data_offset, res.acl_len);
+	if (buf)
+		_copy_from_pages(buf, pages, res.acl_data_offset, res.acl_len);
+out_ok:
+	ret = res.acl_len;
 out_free:
 	for (i = 0; i < npages; i++)
 		if (pages[i])
@@ -3891,10 +3883,13 @@
 		.rpc_argp	= &arg,
 		.rpc_resp	= &res,
 	};
+	unsigned int npages = DIV_ROUND_UP(buflen, PAGE_SIZE);
 	int ret, i;
 
 	if (!nfs4_server_supports_acls(server))
 		return -EOPNOTSUPP;
+	if (npages > ARRAY_SIZE(pages))
+		return -ERANGE;
 	i = buf_to_pages_noslab(buf, buflen, arg.acl_pages, &arg.acl_pgbase);
 	if (i < 0)
 		return i;
diff --git a/fs/nfs/nfs4xdr.c b/fs/nfs/nfs4xdr.c
index 1bfbd67..8dba6bd 100644
--- a/fs/nfs/nfs4xdr.c
+++ b/fs/nfs/nfs4xdr.c
@@ -5072,18 +5072,14 @@
 		 * are stored with the acl data to handle the problem of
 		 * variable length bitmaps.*/
 		res->acl_data_offset = xdr_stream_pos(xdr) - pg_offset;
-
-		/* We ignore &savep and don't do consistency checks on
-		 * the attr length.  Let userspace figure it out.... */
 		res->acl_len = attrlen;
-		if (attrlen > (xdr->nwords << 2)) {
-			if (res->acl_flags & NFS4_ACL_LEN_REQUEST) {
-				/* getxattr interface called with a NULL buf */
-				goto out;
-			}
+
+		/* Check for receive buffer overflow */
+		if (res->acl_len > (xdr->nwords << 2) ||
+		    res->acl_len + res->acl_data_offset > xdr->buf->page_len) {
+			res->acl_flags |= NFS4_ACL_TRUNC;
 			dprintk("NFS: acl reply: attrlen %u > page_len %u\n",
 					attrlen, xdr->nwords << 2);
-			return -EINVAL;
 		}
 	} else
 		status = -EOPNOTSUPP;
@@ -6229,7 +6225,8 @@
 	status = decode_open(xdr, res);
 	if (status)
 		goto out;
-	if (decode_getfh(xdr, &res->fh) != 0)
+	status = decode_getfh(xdr, &res->fh);
+	if (status)
 		goto out;
 	decode_getfattr(xdr, res->f_attr, res->server);
 out:
diff --git a/fs/nfs/super.c b/fs/nfs/super.c
index 239aff7..b8eda70 100644
--- a/fs/nfs/super.c
+++ b/fs/nfs/super.c
@@ -1867,6 +1867,7 @@
 
 		memcpy(sap, &data->addr, sizeof(data->addr));
 		args->nfs_server.addrlen = sizeof(data->addr);
+		args->nfs_server.port = ntohs(data->addr.sin_port);
 		if (!nfs_verify_server_address(sap))
 			goto out_no_address;
 
@@ -2564,6 +2565,7 @@
 			return -EFAULT;
 		if (!nfs_verify_server_address(sap))
 			goto out_no_address;
+		args->nfs_server.port = ntohs(((struct sockaddr_in *)sap)->sin_port);
 
 		if (data->auth_flavourlen) {
 			if (data->auth_flavourlen > 1)
diff --git a/fs/stat.c b/fs/stat.c
index b6ff118..4078022 100644
--- a/fs/stat.c
+++ b/fs/stat.c
@@ -58,7 +58,7 @@
 int vfs_fstat(unsigned int fd, struct kstat *stat)
 {
 	int fput_needed;
-	struct file *f = fget_light(fd, &fput_needed);
+	struct file *f = fget_raw_light(fd, &fput_needed);
 	int error = -EBADF;
 
 	if (f) {
diff --git a/fs/udf/file.c b/fs/udf/file.c
index 7f3f7ba..d1c6093 100644
--- a/fs/udf/file.c
+++ b/fs/udf/file.c
@@ -39,20 +39,24 @@
 #include "udf_i.h"
 #include "udf_sb.h"
 
-static int udf_adinicb_readpage(struct file *file, struct page *page)
+static void __udf_adinicb_readpage(struct page *page)
 {
 	struct inode *inode = page->mapping->host;
 	char *kaddr;
 	struct udf_inode_info *iinfo = UDF_I(inode);
 
-	BUG_ON(!PageLocked(page));
-
 	kaddr = kmap(page);
-	memset(kaddr, 0, PAGE_CACHE_SIZE);
 	memcpy(kaddr, iinfo->i_ext.i_data + iinfo->i_lenEAttr, inode->i_size);
+	memset(kaddr + inode->i_size, 0, PAGE_CACHE_SIZE - inode->i_size);
 	flush_dcache_page(page);
 	SetPageUptodate(page);
 	kunmap(page);
+}
+
+static int udf_adinicb_readpage(struct file *file, struct page *page)
+{
+	BUG_ON(!PageLocked(page));
+	__udf_adinicb_readpage(page);
 	unlock_page(page);
 
 	return 0;
@@ -77,6 +81,25 @@
 	return 0;
 }
 
+static int udf_adinicb_write_begin(struct file *file,
+			struct address_space *mapping, loff_t pos,
+			unsigned len, unsigned flags, struct page **pagep,
+			void **fsdata)
+{
+	struct page *page;
+
+	if (WARN_ON_ONCE(pos >= PAGE_CACHE_SIZE))
+		return -EIO;
+	page = grab_cache_page_write_begin(mapping, 0, flags);
+	if (!page)
+		return -ENOMEM;
+	*pagep = page;
+
+	if (!PageUptodate(page) && len != PAGE_CACHE_SIZE)
+		__udf_adinicb_readpage(page);
+	return 0;
+}
+
 static int udf_adinicb_write_end(struct file *file,
 			struct address_space *mapping,
 			loff_t pos, unsigned len, unsigned copied,
@@ -98,8 +121,8 @@
 const struct address_space_operations udf_adinicb_aops = {
 	.readpage	= udf_adinicb_readpage,
 	.writepage	= udf_adinicb_writepage,
-	.write_begin = simple_write_begin,
-	.write_end = udf_adinicb_write_end,
+	.write_begin	= udf_adinicb_write_begin,
+	.write_end	= udf_adinicb_write_end,
 };
 
 static ssize_t udf_file_aio_write(struct kiocb *iocb, const struct iovec *iov,
diff --git a/include/drm/drm_fourcc.h b/include/drm/drm_fourcc.h
index bdf0152..f462118 100644
--- a/include/drm/drm_fourcc.h
+++ b/include/drm/drm_fourcc.h
@@ -107,8 +107,7 @@
 #define DRM_FORMAT_NV16		fourcc_code('N', 'V', '1', '6') /* 2x1 subsampled Cr:Cb plane */
 #define DRM_FORMAT_NV61		fourcc_code('N', 'V', '6', '1') /* 2x1 subsampled Cb:Cr plane */
 
-/* 2 non contiguous plane YCbCr */
-#define DRM_FORMAT_NV12M	fourcc_code('N', 'M', '1', '2') /* 2x2 subsampled Cr:Cb plane */
+/* special NV12 tiled format */
 #define DRM_FORMAT_NV12MT	fourcc_code('T', 'M', '1', '2') /* 2x2 subsampled Cr:Cb plane 64x32 macroblocks */
 
 /*
@@ -131,7 +130,4 @@
 #define DRM_FORMAT_YUV444	fourcc_code('Y', 'U', '2', '4') /* non-subsampled Cb (1) and Cr (2) planes */
 #define DRM_FORMAT_YVU444	fourcc_code('Y', 'V', '2', '4') /* non-subsampled Cr (1) and Cb (2) planes */
 
-/* 3 non contiguous plane YCbCr */
-#define DRM_FORMAT_YUV420M	fourcc_code('Y', 'M', '1', '2') /* 2x2 subsampled Cb (1) and Cr (2) planes */
-
 #endif /* DRM_FOURCC_H */
diff --git a/include/linux/i2c-pnx.h b/include/linux/i2c-pnx.h
index 1bc74af..49ed17f 100644
--- a/include/linux/i2c-pnx.h
+++ b/include/linux/i2c-pnx.h
@@ -22,6 +22,7 @@
 	struct timer_list	timer;		/* Timeout */
 	u8 *			buf;		/* Data buffer */
 	int			len;		/* Length of data buffer */
+	int			order;		/* RX Bytes to order via TX */
 };
 
 struct i2c_pnx_algo_data {
diff --git a/include/linux/kernel.h b/include/linux/kernel.h
index 6043821..594b419 100644
--- a/include/linux/kernel.h
+++ b/include/linux/kernel.h
@@ -82,10 +82,18 @@
 	__x - (__x % (y));				\
 }							\
 )
+
+/*
+ * Divide positive or negative dividend by positive divisor and round
+ * to closest integer. Result is undefined for negative divisors.
+ */
 #define DIV_ROUND_CLOSEST(x, divisor)(			\
 {							\
-	typeof(divisor) __divisor = divisor;		\
-	(((x) + ((__divisor) / 2)) / (__divisor));	\
+	typeof(x) __x = x;				\
+	typeof(divisor) __d = divisor;			\
+	(((typeof(x))-1) >= 0 || (__x) >= 0) ?		\
+		(((__x) + ((__d) / 2)) / (__d)) :	\
+		(((__x) - ((__d) / 2)) / (__d));	\
 }							\
 )
 
diff --git a/include/linux/kobject.h b/include/linux/kobject.h
index fc615a9..1e57449 100644
--- a/include/linux/kobject.h
+++ b/include/linux/kobject.h
@@ -224,7 +224,7 @@
 
 static inline __printf(2, 3)
 int add_uevent_var(struct kobj_uevent_env *env, const char *format, ...)
-{ return 0; }
+{ return -ENOMEM; }
 
 static inline int kobject_action_type(const char *buf, size_t count,
 				      enum kobject_action *type)
diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h
index 111aca5..4b27f9f 100644
--- a/include/linux/mmc/card.h
+++ b/include/linux/mmc/card.h
@@ -239,6 +239,7 @@
 #define MMC_QUIRK_BLK_NO_CMD23	(1<<7)		/* Avoid CMD23 for regular multiblock */
 #define MMC_QUIRK_BROKEN_BYTE_MODE_512 (1<<8)	/* Avoid sending 512 bytes in */
 #define MMC_QUIRK_LONG_READ_TIME (1<<9)		/* Data read time > CSD says */
+#define MMC_QUIRK_SEC_ERASE_TRIM_BROKEN (1<<10)	/* Skip secure for erase/trim */
 						/* byte mode */
 	unsigned int    poweroff_notify_state;	/* eMMC4.5 notify feature */
 #define MMC_NO_POWER_NOTIFICATION	0
diff --git a/include/linux/nfs_fs.h b/include/linux/nfs_fs.h
index 1f8fc7f..4b03f56 100644
--- a/include/linux/nfs_fs.h
+++ b/include/linux/nfs_fs.h
@@ -265,11 +265,6 @@
 	return NFS_SERVER(inode)->nfs_client->rpc_ops;
 }
 
-static inline __be32 *NFS_COOKIEVERF(const struct inode *inode)
-{
-	return NFS_I(inode)->cookieverf;
-}
-
 static inline unsigned NFS_MINATTRTIMEO(const struct inode *inode)
 {
 	struct nfs_server *nfss = NFS_SERVER(inode);
diff --git a/include/linux/nfs_xdr.h b/include/linux/nfs_xdr.h
index ac7c8ae2..be9cf3c 100644
--- a/include/linux/nfs_xdr.h
+++ b/include/linux/nfs_xdr.h
@@ -652,7 +652,7 @@
 };
 
 /* getxattr ACL interface flags */
-#define NFS4_ACL_LEN_REQUEST	0x0001	/* zero length getxattr buffer */
+#define NFS4_ACL_TRUNC		0x0001	/* ACL was truncated */
 struct nfs_getaclres {
 	size_t				acl_len;
 	size_t				acl_data_offset;
diff --git a/include/linux/perf_event.h b/include/linux/perf_event.h
index 7602ccb..33ed9d6 100644
--- a/include/linux/perf_event.h
+++ b/include/linux/perf_event.h
@@ -926,7 +926,7 @@
 	struct hw_perf_event		hw;
 
 	struct perf_event_context	*ctx;
-	struct file			*filp;
+	atomic_long_t			refcount;
 
 	/*
 	 * These accumulate total time (in nanoseconds) that children
@@ -1296,6 +1296,7 @@
 extern void perf_swevent_put_recursion_context(int rctx);
 extern void perf_event_enable(struct perf_event *event);
 extern void perf_event_disable(struct perf_event *event);
+extern int __perf_event_disable(void *info);
 extern void perf_event_task_tick(void);
 #else
 static inline void
@@ -1334,6 +1335,7 @@
 static inline void perf_swevent_put_recursion_context(int rctx)		{ }
 static inline void perf_event_enable(struct perf_event *event)		{ }
 static inline void perf_event_disable(struct perf_event *event)		{ }
+static inline int __perf_event_disable(void *info)			{ return -1; }
 static inline void perf_event_task_tick(void)				{ }
 #endif
 
diff --git a/include/linux/sunrpc/xprt.h b/include/linux/sunrpc/xprt.h
index cff40aa..bf8c49f 100644
--- a/include/linux/sunrpc/xprt.h
+++ b/include/linux/sunrpc/xprt.h
@@ -114,6 +114,7 @@
 	void		(*set_buffer_size)(struct rpc_xprt *xprt, size_t sndsize, size_t rcvsize);
 	int		(*reserve_xprt)(struct rpc_xprt *xprt, struct rpc_task *task);
 	void		(*release_xprt)(struct rpc_xprt *xprt, struct rpc_task *task);
+	void		(*alloc_slot)(struct rpc_xprt *xprt, struct rpc_task *task);
 	void		(*rpcbind)(struct rpc_task *task);
 	void		(*set_port)(struct rpc_xprt *xprt, unsigned short port);
 	void		(*connect)(struct rpc_task *task);
@@ -281,6 +282,8 @@
 void			xprt_reserve(struct rpc_task *task);
 int			xprt_reserve_xprt(struct rpc_xprt *xprt, struct rpc_task *task);
 int			xprt_reserve_xprt_cong(struct rpc_xprt *xprt, struct rpc_task *task);
+void			xprt_alloc_slot(struct rpc_xprt *xprt, struct rpc_task *task);
+void			xprt_lock_and_alloc_slot(struct rpc_xprt *xprt, struct rpc_task *task);
 int			xprt_prepare_transmit(struct rpc_task *task);
 void			xprt_transmit(struct rpc_task *task);
 void			xprt_end_transmit(struct rpc_task *task);
diff --git a/kernel/events/core.c b/kernel/events/core.c
index b7935fc..7fee567 100644
--- a/kernel/events/core.c
+++ b/kernel/events/core.c
@@ -1253,7 +1253,7 @@
 /*
  * Cross CPU call to disable a performance event
  */
-static int __perf_event_disable(void *info)
+int __perf_event_disable(void *info)
 {
 	struct perf_event *event = info;
 	struct perf_event_context *ctx = event->ctx;
@@ -2935,12 +2935,12 @@
 /*
  * Called when the last reference to the file is gone.
  */
-static int perf_release(struct inode *inode, struct file *file)
+static void put_event(struct perf_event *event)
 {
-	struct perf_event *event = file->private_data;
 	struct task_struct *owner;
 
-	file->private_data = NULL;
+	if (!atomic_long_dec_and_test(&event->refcount))
+		return;
 
 	rcu_read_lock();
 	owner = ACCESS_ONCE(event->owner);
@@ -2975,7 +2975,13 @@
 		put_task_struct(owner);
 	}
 
-	return perf_event_release_kernel(event);
+	perf_event_release_kernel(event);
+}
+
+static int perf_release(struct inode *inode, struct file *file)
+{
+	put_event(file->private_data);
+	return 0;
 }
 
 u64 perf_event_read_value(struct perf_event *event, u64 *enabled, u64 *running)
@@ -3227,7 +3233,7 @@
 
 static const struct file_operations perf_fops;
 
-static struct perf_event *perf_fget_light(int fd, int *fput_needed)
+static struct file *perf_fget_light(int fd, int *fput_needed)
 {
 	struct file *file;
 
@@ -3241,7 +3247,7 @@
 		return ERR_PTR(-EBADF);
 	}
 
-	return file->private_data;
+	return file;
 }
 
 static int perf_event_set_output(struct perf_event *event,
@@ -3273,19 +3279,21 @@
 
 	case PERF_EVENT_IOC_SET_OUTPUT:
 	{
+		struct file *output_file = NULL;
 		struct perf_event *output_event = NULL;
 		int fput_needed = 0;
 		int ret;
 
 		if (arg != -1) {
-			output_event = perf_fget_light(arg, &fput_needed);
-			if (IS_ERR(output_event))
-				return PTR_ERR(output_event);
+			output_file = perf_fget_light(arg, &fput_needed);
+			if (IS_ERR(output_file))
+				return PTR_ERR(output_file);
+			output_event = output_file->private_data;
 		}
 
 		ret = perf_event_set_output(event, output_event);
 		if (output_event)
-			fput_light(output_event->filp, fput_needed);
+			fput_light(output_file, fput_needed);
 
 		return ret;
 	}
@@ -5950,6 +5958,7 @@
 
 	mutex_init(&event->mmap_mutex);
 
+	atomic_long_set(&event->refcount, 1);
 	event->cpu		= cpu;
 	event->attr		= *attr;
 	event->group_leader	= group_leader;
@@ -6260,12 +6269,12 @@
 		return event_fd;
 
 	if (group_fd != -1) {
-		group_leader = perf_fget_light(group_fd, &fput_needed);
-		if (IS_ERR(group_leader)) {
-			err = PTR_ERR(group_leader);
+		group_file = perf_fget_light(group_fd, &fput_needed);
+		if (IS_ERR(group_file)) {
+			err = PTR_ERR(group_file);
 			goto err_fd;
 		}
-		group_file = group_leader->filp;
+		group_leader = group_file->private_data;
 		if (flags & PERF_FLAG_FD_OUTPUT)
 			output_event = group_leader;
 		if (flags & PERF_FLAG_FD_NO_GROUP)
@@ -6402,7 +6411,6 @@
 		put_ctx(gctx);
 	}
 
-	event->filp = event_file;
 	WARN_ON_ONCE(ctx->parent_ctx);
 	mutex_lock(&ctx->mutex);
 
@@ -6496,7 +6504,6 @@
 		goto err_free;
 	}
 
-	event->filp = NULL;
 	WARN_ON_ONCE(ctx->parent_ctx);
 	mutex_lock(&ctx->mutex);
 	perf_install_in_context(ctx, event, cpu);
@@ -6578,7 +6585,7 @@
 	 * Release the parent event, if this was the last
 	 * reference to it.
 	 */
-	fput(parent_event->filp);
+	put_event(parent_event);
 }
 
 static void
@@ -6654,9 +6661,8 @@
 	 *
 	 *   __perf_event_exit_task()
 	 *     sync_child_event()
-	 *       fput(parent_event->filp)
-	 *         perf_release()
-	 *           mutex_lock(&ctx->mutex)
+	 *       put_event()
+	 *         mutex_lock(&ctx->mutex)
 	 *
 	 * But since its the parent context it won't be the same instance.
 	 */
@@ -6724,7 +6730,7 @@
 	list_del_init(&event->child_list);
 	mutex_unlock(&parent->child_mutex);
 
-	fput(parent->filp);
+	put_event(parent);
 
 	perf_group_detach(event);
 	list_del_event(event, ctx);
@@ -6804,6 +6810,12 @@
 				           NULL, NULL);
 	if (IS_ERR(child_event))
 		return child_event;
+
+	if (!atomic_long_inc_not_zero(&parent_event->refcount)) {
+		free_event(child_event);
+		return NULL;
+	}
+
 	get_ctx(child_ctx);
 
 	/*
@@ -6845,14 +6857,6 @@
 	raw_spin_unlock_irqrestore(&child_ctx->lock, flags);
 
 	/*
-	 * Get a reference to the parent filp - we will fput it
-	 * when the child event exits. This is safe to do because
-	 * we are in the parent and we know that the filp still
-	 * exists and has a nonzero count:
-	 */
-	atomic_long_inc(&parent_event->filp->f_count);
-
-	/*
 	 * Link this into the parent event's child list
 	 */
 	WARN_ON_ONCE(parent_event->ctx->parent_ctx);
diff --git a/kernel/events/hw_breakpoint.c b/kernel/events/hw_breakpoint.c
index bb38c4d..9a7b487 100644
--- a/kernel/events/hw_breakpoint.c
+++ b/kernel/events/hw_breakpoint.c
@@ -453,7 +453,16 @@
 	int old_type = bp->attr.bp_type;
 	int err = 0;
 
-	perf_event_disable(bp);
+	/*
+	 * modify_user_hw_breakpoint can be invoked with IRQs disabled and hence it
+	 * will not be possible to raise IPIs that invoke __perf_event_disable.
+	 * So call the function directly after making sure we are targeting the
+	 * current task.
+	 */
+	if (irqs_disabled() && bp->ctx && bp->ctx->task == current)
+		__perf_event_disable(bp);
+	else
+		perf_event_disable(bp);
 
 	bp->attr.bp_addr = attr->bp_addr;
 	bp->attr.bp_type = attr->bp_type;
diff --git a/kernel/sched/core.c b/kernel/sched/core.c
index fbf1fd0..a4ea245 100644
--- a/kernel/sched/core.c
+++ b/kernel/sched/core.c
@@ -5304,27 +5304,17 @@
 }
 
 /*
- * While a dead CPU has no uninterruptible tasks queued at this point,
- * it might still have a nonzero ->nr_uninterruptible counter, because
- * for performance reasons the counter is not stricly tracking tasks to
- * their home CPUs. So we just add the counter to another CPU's counter,
- * to keep the global sum constant after CPU-down:
+ * Since this CPU is going 'away' for a while, fold any nr_active delta
+ * we might have. Assumes we're called after migrate_tasks() so that the
+ * nr_active count is stable.
+ *
+ * Also see the comment "Global load-average calculations".
  */
-static void migrate_nr_uninterruptible(struct rq *rq_src)
+static void calc_load_migrate(struct rq *rq)
 {
-	struct rq *rq_dest = cpu_rq(cpumask_any(cpu_active_mask));
-
-	rq_dest->nr_uninterruptible += rq_src->nr_uninterruptible;
-	rq_src->nr_uninterruptible = 0;
-}
-
-/*
- * remove the tasks which were accounted by rq from calc_load_tasks.
- */
-static void calc_global_load_remove(struct rq *rq)
-{
-	atomic_long_sub(rq->calc_load_active, &calc_load_tasks);
-	rq->calc_load_active = 0;
+	long delta = calc_load_fold_active(rq);
+	if (delta)
+		atomic_long_add(delta, &calc_load_tasks);
 }
 
 /*
@@ -5352,9 +5342,6 @@
 	 */
 	rq->stop = NULL;
 
-	/* Ensure any throttled groups are reachable by pick_next_task */
-	unthrottle_offline_cfs_rqs(rq);
-
 	for ( ; ; ) {
 		/*
 		 * There's this thread running, bail when that's the only
@@ -5618,8 +5605,7 @@
 		BUG_ON(rq->nr_running != 1); /* the migration thread */
 		raw_spin_unlock_irqrestore(&rq->lock, flags);
 
-		migrate_nr_uninterruptible(rq);
-		calc_global_load_remove(rq);
+		calc_load_migrate(rq);
 		break;
 #endif
 	}
diff --git a/kernel/sched/fair.c b/kernel/sched/fair.c
index c219bf8..42d9df6 100644
--- a/kernel/sched/fair.c
+++ b/kernel/sched/fair.c
@@ -2052,7 +2052,7 @@
 	hrtimer_cancel(&cfs_b->slack_timer);
 }
 
-void unthrottle_offline_cfs_rqs(struct rq *rq)
+static void unthrottle_offline_cfs_rqs(struct rq *rq)
 {
 	struct cfs_rq *cfs_rq;
 
@@ -2106,7 +2106,7 @@
 	return NULL;
 }
 static inline void destroy_cfs_bandwidth(struct cfs_bandwidth *cfs_b) {}
-void unthrottle_offline_cfs_rqs(struct rq *rq) {}
+static inline void unthrottle_offline_cfs_rqs(struct rq *rq) {}
 
 #endif /* CONFIG_CFS_BANDWIDTH */
 
@@ -3658,7 +3658,6 @@
  * @group: sched_group whose statistics are to be updated.
  * @load_idx: Load index of sched_domain of this_cpu for load calc.
  * @local_group: Does group contain this_cpu.
- * @cpus: Set of cpus considered for load balancing.
  * @balance: Should we balance.
  * @sgs: variable to hold the statistics for this group.
  */
@@ -3805,7 +3804,6 @@
 /**
  * update_sd_lb_stats - Update sched_domain's statistics for load balancing.
  * @env: The load balancing environment.
- * @cpus: Set of cpus considered for load balancing.
  * @balance: Should we balance.
  * @sds: variable to hold the statistics for this sched_domain.
  */
@@ -4956,6 +4954,9 @@
 static void rq_offline_fair(struct rq *rq)
 {
 	update_sysctl();
+
+	/* Ensure any throttled groups are reachable by pick_next_task */
+	unthrottle_offline_cfs_rqs(rq);
 }
 
 #endif /* CONFIG_SMP */
diff --git a/kernel/sched/rt.c b/kernel/sched/rt.c
index 944cb68..e0b7ba9 100644
--- a/kernel/sched/rt.c
+++ b/kernel/sched/rt.c
@@ -691,6 +691,7 @@
 		 * runtime - in which case borrowing doesn't make sense.
 		 */
 		rt_rq->rt_runtime = RUNTIME_INF;
+		rt_rq->rt_throttled = 0;
 		raw_spin_unlock(&rt_rq->rt_runtime_lock);
 		raw_spin_unlock(&rt_b->rt_runtime_lock);
 	}
diff --git a/kernel/sched/sched.h b/kernel/sched/sched.h
index f6714d0..0848fa3 100644
--- a/kernel/sched/sched.h
+++ b/kernel/sched/sched.h
@@ -1144,7 +1144,6 @@
 
 extern void init_cfs_rq(struct cfs_rq *cfs_rq);
 extern void init_rt_rq(struct rt_rq *rt_rq, struct rq *rq);
-extern void unthrottle_offline_cfs_rqs(struct rq *rq);
 
 extern void account_cfs_bandwidth_used(int enabled, int was_enabled);
 
diff --git a/kernel/time/tick-sched.c b/kernel/time/tick-sched.c
index 024540f..3a9e5d5 100644
--- a/kernel/time/tick-sched.c
+++ b/kernel/time/tick-sched.c
@@ -573,6 +573,7 @@
 	tick_do_update_jiffies64(now);
 	update_cpu_load_nohz();
 
+	calc_load_exit_idle();
 	touch_softlockup_watchdog();
 	/*
 	 * Cancel the scheduled timer and restore the tick
diff --git a/kernel/workqueue.c b/kernel/workqueue.c
index 692d976..1e1373b 100644
--- a/kernel/workqueue.c
+++ b/kernel/workqueue.c
@@ -66,6 +66,7 @@
 
 	/* pool flags */
 	POOL_MANAGE_WORKERS	= 1 << 0,	/* need to manage workers */
+	POOL_MANAGING_WORKERS   = 1 << 1,       /* managing workers */
 
 	/* worker flags */
 	WORKER_STARTED		= 1 << 0,	/* started */
@@ -652,7 +653,7 @@
 /* Do we have too many workers and should some go away? */
 static bool too_many_workers(struct worker_pool *pool)
 {
-	bool managing = mutex_is_locked(&pool->manager_mutex);
+	bool managing = pool->flags & POOL_MANAGING_WORKERS;
 	int nr_idle = pool->nr_idle + managing; /* manager is considered idle */
 	int nr_busy = pool->nr_workers - nr_idle;
 
@@ -1326,6 +1327,15 @@
 
 	/* we did our part, wait for rebind_workers() to finish up */
 	wait_event(gcwq->rebind_hold, !(worker->flags & WORKER_REBIND));
+
+	/*
+	 * rebind_workers() shouldn't finish until all workers passed the
+	 * above WORKER_REBIND wait.  Tell it when done.
+	 */
+	spin_lock_irq(&worker->pool->gcwq->lock);
+	if (!--worker->idle_rebind->cnt)
+		complete(&worker->idle_rebind->done);
+	spin_unlock_irq(&worker->pool->gcwq->lock);
 }
 
 /*
@@ -1396,12 +1406,15 @@
 	/* set REBIND and kick idle ones, we'll wait for these later */
 	for_each_worker_pool(pool, gcwq) {
 		list_for_each_entry(worker, &pool->idle_list, entry) {
+			unsigned long worker_flags = worker->flags;
+
 			if (worker->flags & WORKER_REBIND)
 				continue;
 
-			/* morph UNBOUND to REBIND */
-			worker->flags &= ~WORKER_UNBOUND;
-			worker->flags |= WORKER_REBIND;
+			/* morph UNBOUND to REBIND atomically */
+			worker_flags &= ~WORKER_UNBOUND;
+			worker_flags |= WORKER_REBIND;
+			ACCESS_ONCE(worker->flags) = worker_flags;
 
 			idle_rebind.cnt++;
 			worker->idle_rebind = &idle_rebind;
@@ -1419,25 +1432,15 @@
 		goto retry;
 	}
 
-	/*
-	 * All idle workers are rebound and waiting for %WORKER_REBIND to
-	 * be cleared inside idle_worker_rebind().  Clear and release.
-	 * Clearing %WORKER_REBIND from this foreign context is safe
-	 * because these workers are still guaranteed to be idle.
-	 */
-	for_each_worker_pool(pool, gcwq)
-		list_for_each_entry(worker, &pool->idle_list, entry)
-			worker->flags &= ~WORKER_REBIND;
-
-	wake_up_all(&gcwq->rebind_hold);
-
-	/* rebind busy workers */
+	/* all idle workers are rebound, rebind busy workers */
 	for_each_busy_worker(worker, i, pos, gcwq) {
 		struct work_struct *rebind_work = &worker->rebind_work;
+		unsigned long worker_flags = worker->flags;
 
-		/* morph UNBOUND to REBIND */
-		worker->flags &= ~WORKER_UNBOUND;
-		worker->flags |= WORKER_REBIND;
+		/* morph UNBOUND to REBIND atomically */
+		worker_flags &= ~WORKER_UNBOUND;
+		worker_flags |= WORKER_REBIND;
+		ACCESS_ONCE(worker->flags) = worker_flags;
 
 		if (test_and_set_bit(WORK_STRUCT_PENDING_BIT,
 				     work_data_bits(rebind_work)))
@@ -1449,6 +1452,34 @@
 			    worker->scheduled.next,
 			    work_color_to_flags(WORK_NO_COLOR));
 	}
+
+	/*
+	 * All idle workers are rebound and waiting for %WORKER_REBIND to
+	 * be cleared inside idle_worker_rebind().  Clear and release.
+	 * Clearing %WORKER_REBIND from this foreign context is safe
+	 * because these workers are still guaranteed to be idle.
+	 *
+	 * We need to make sure all idle workers passed WORKER_REBIND wait
+	 * in idle_worker_rebind() before returning; otherwise, workers can
+	 * get stuck at the wait if hotplug cycle repeats.
+	 */
+	idle_rebind.cnt = 1;
+	INIT_COMPLETION(idle_rebind.done);
+
+	for_each_worker_pool(pool, gcwq) {
+		list_for_each_entry(worker, &pool->idle_list, entry) {
+			worker->flags &= ~WORKER_REBIND;
+			idle_rebind.cnt++;
+		}
+	}
+
+	wake_up_all(&gcwq->rebind_hold);
+
+	if (--idle_rebind.cnt) {
+		spin_unlock_irq(&gcwq->lock);
+		wait_for_completion(&idle_rebind.done);
+		spin_lock_irq(&gcwq->lock);
+	}
 }
 
 static struct worker *alloc_worker(void)
@@ -1794,9 +1825,45 @@
 	struct worker_pool *pool = worker->pool;
 	bool ret = false;
 
-	if (!mutex_trylock(&pool->manager_mutex))
+	if (pool->flags & POOL_MANAGING_WORKERS)
 		return ret;
 
+	pool->flags |= POOL_MANAGING_WORKERS;
+
+	/*
+	 * To simplify both worker management and CPU hotplug, hold off
+	 * management while hotplug is in progress.  CPU hotplug path can't
+	 * grab %POOL_MANAGING_WORKERS to achieve this because that can
+	 * lead to idle worker depletion (all become busy thinking someone
+	 * else is managing) which in turn can result in deadlock under
+	 * extreme circumstances.  Use @pool->manager_mutex to synchronize
+	 * manager against CPU hotplug.
+	 *
+	 * manager_mutex would always be free unless CPU hotplug is in
+	 * progress.  trylock first without dropping @gcwq->lock.
+	 */
+	if (unlikely(!mutex_trylock(&pool->manager_mutex))) {
+		spin_unlock_irq(&pool->gcwq->lock);
+		mutex_lock(&pool->manager_mutex);
+		/*
+		 * CPU hotplug could have happened while we were waiting
+		 * for manager_mutex.  Hotplug itself can't handle us
+		 * because manager isn't either on idle or busy list, and
+		 * @gcwq's state and ours could have deviated.
+		 *
+		 * As hotplug is now excluded via manager_mutex, we can
+		 * simply try to bind.  It will succeed or fail depending
+		 * on @gcwq's current state.  Try it and adjust
+		 * %WORKER_UNBOUND accordingly.
+		 */
+		if (worker_maybe_bind_and_lock(worker))
+			worker->flags &= ~WORKER_UNBOUND;
+		else
+			worker->flags |= WORKER_UNBOUND;
+
+		ret = true;
+	}
+
 	pool->flags &= ~POOL_MANAGE_WORKERS;
 
 	/*
@@ -1806,6 +1873,7 @@
 	ret |= maybe_destroy_workers(pool);
 	ret |= maybe_create_worker(pool);
 
+	pool->flags &= ~POOL_MANAGING_WORKERS;
 	mutex_unlock(&pool->manager_mutex);
 	return ret;
 }
diff --git a/lib/digsig.c b/lib/digsig.c
index 286d558..8c0e629 100644
--- a/lib/digsig.c
+++ b/lib/digsig.c
@@ -163,9 +163,11 @@
 	memcpy(out1 + head, p, l);
 
 	err = pkcs_1_v1_5_decode_emsa(out1, len, mblen, out2, &len);
+	if (err)
+		goto err;
 
-	if (!err && len == hlen)
-		err = memcmp(out2, h, hlen);
+	if (len != hlen || memcmp(out2, h, hlen))
+		err = -EINVAL;
 
 err:
 	mpi_free(in);
diff --git a/mm/memblock.c b/mm/memblock.c
index 4d9393c..82aa349 100644
--- a/mm/memblock.c
+++ b/mm/memblock.c
@@ -246,7 +246,7 @@
 				min(new_area_start, memblock.current_limit),
 				new_alloc_size, PAGE_SIZE);
 
-		new_array = addr ? __va(addr) : 0;
+		new_array = addr ? __va(addr) : NULL;
 	}
 	if (!addr) {
 		pr_err("memblock: Failed to double %s array from %ld to %ld entries !\n",
diff --git a/mm/mempolicy.c b/mm/mempolicy.c
index bd92431..4ada3be 100644
--- a/mm/mempolicy.c
+++ b/mm/mempolicy.c
@@ -2562,7 +2562,7 @@
 		break;
 
 	default:
-		BUG();
+		return -EINVAL;
 	}
 
 	l = strlen(policy_modes[mode]);
diff --git a/net/socket.c b/net/socket.c
index a5471f8..edc3c4a 100644
--- a/net/socket.c
+++ b/net/socket.c
@@ -2604,7 +2604,7 @@
 	err = sock_do_ioctl(net, sock, cmd, (unsigned long)&ktv);
 	set_fs(old_fs);
 	if (!err)
-		err = compat_put_timeval(up, &ktv);
+		err = compat_put_timeval(&ktv, up);
 
 	return err;
 }
@@ -2620,7 +2620,7 @@
 	err = sock_do_ioctl(net, sock, cmd, (unsigned long)&kts);
 	set_fs(old_fs);
 	if (!err)
-		err = compat_put_timespec(up, &kts);
+		err = compat_put_timespec(&kts, up);
 
 	return err;
 }
diff --git a/net/sunrpc/xprt.c b/net/sunrpc/xprt.c
index a5a402a..5d7f61d 100644
--- a/net/sunrpc/xprt.c
+++ b/net/sunrpc/xprt.c
@@ -969,11 +969,11 @@
 	return false;
 }
 
-static void xprt_alloc_slot(struct rpc_task *task)
+void xprt_alloc_slot(struct rpc_xprt *xprt, struct rpc_task *task)
 {
-	struct rpc_xprt	*xprt = task->tk_xprt;
 	struct rpc_rqst *req;
 
+	spin_lock(&xprt->reserve_lock);
 	if (!list_empty(&xprt->free)) {
 		req = list_entry(xprt->free.next, struct rpc_rqst, rq_list);
 		list_del(&req->rq_list);
@@ -994,12 +994,29 @@
 	default:
 		task->tk_status = -EAGAIN;
 	}
+	spin_unlock(&xprt->reserve_lock);
 	return;
 out_init_req:
 	task->tk_status = 0;
 	task->tk_rqstp = req;
 	xprt_request_init(task, xprt);
+	spin_unlock(&xprt->reserve_lock);
 }
+EXPORT_SYMBOL_GPL(xprt_alloc_slot);
+
+void xprt_lock_and_alloc_slot(struct rpc_xprt *xprt, struct rpc_task *task)
+{
+	/* Note: grabbing the xprt_lock_write() ensures that we throttle
+	 * new slot allocation if the transport is congested (i.e. when
+	 * reconnecting a stream transport or when out of socket write
+	 * buffer space).
+	 */
+	if (xprt_lock_write(xprt, task)) {
+		xprt_alloc_slot(xprt, task);
+		xprt_release_write(xprt, task);
+	}
+}
+EXPORT_SYMBOL_GPL(xprt_lock_and_alloc_slot);
 
 static void xprt_free_slot(struct rpc_xprt *xprt, struct rpc_rqst *req)
 {
@@ -1083,20 +1100,9 @@
 	if (task->tk_rqstp != NULL)
 		return;
 
-	/* Note: grabbing the xprt_lock_write() here is not strictly needed,
-	 * but ensures that we throttle new slot allocation if the transport
-	 * is congested (e.g. if reconnecting or if we're out of socket
-	 * write buffer space).
-	 */
 	task->tk_timeout = 0;
 	task->tk_status = -EAGAIN;
-	if (!xprt_lock_write(xprt, task))
-		return;
-
-	spin_lock(&xprt->reserve_lock);
-	xprt_alloc_slot(task);
-	spin_unlock(&xprt->reserve_lock);
-	xprt_release_write(xprt, task);
+	xprt->ops->alloc_slot(xprt, task);
 }
 
 static inline __be32 xprt_alloc_xid(struct rpc_xprt *xprt)
diff --git a/net/sunrpc/xprtrdma/transport.c b/net/sunrpc/xprtrdma/transport.c
index 06cdbff..5d9202d 100644
--- a/net/sunrpc/xprtrdma/transport.c
+++ b/net/sunrpc/xprtrdma/transport.c
@@ -713,6 +713,7 @@
 static struct rpc_xprt_ops xprt_rdma_procs = {
 	.reserve_xprt		= xprt_rdma_reserve_xprt,
 	.release_xprt		= xprt_release_xprt_cong, /* sunrpc/xprt.c */
+	.alloc_slot		= xprt_alloc_slot,
 	.release_request	= xprt_release_rqst_cong,       /* ditto */
 	.set_retrans_timeout	= xprt_set_retrans_timeout_def, /* ditto */
 	.rpcbind		= rpcb_getport_async,	/* sunrpc/rpcb_clnt.c */
diff --git a/net/sunrpc/xprtsock.c b/net/sunrpc/xprtsock.c
index 4005672..a35b8e5 100644
--- a/net/sunrpc/xprtsock.c
+++ b/net/sunrpc/xprtsock.c
@@ -2473,6 +2473,7 @@
 static struct rpc_xprt_ops xs_local_ops = {
 	.reserve_xprt		= xprt_reserve_xprt,
 	.release_xprt		= xs_tcp_release_xprt,
+	.alloc_slot		= xprt_alloc_slot,
 	.rpcbind		= xs_local_rpcbind,
 	.set_port		= xs_local_set_port,
 	.connect		= xs_connect,
@@ -2489,6 +2490,7 @@
 	.set_buffer_size	= xs_udp_set_buffer_size,
 	.reserve_xprt		= xprt_reserve_xprt_cong,
 	.release_xprt		= xprt_release_xprt_cong,
+	.alloc_slot		= xprt_alloc_slot,
 	.rpcbind		= rpcb_getport_async,
 	.set_port		= xs_set_port,
 	.connect		= xs_connect,
@@ -2506,6 +2508,7 @@
 static struct rpc_xprt_ops xs_tcp_ops = {
 	.reserve_xprt		= xprt_reserve_xprt,
 	.release_xprt		= xs_tcp_release_xprt,
+	.alloc_slot		= xprt_lock_and_alloc_slot,
 	.rpcbind		= rpcb_getport_async,
 	.set_port		= xs_set_port,
 	.connect		= xs_connect,
diff --git a/scripts/Makefile.fwinst b/scripts/Makefile.fwinst
index 6bf8e87..c3f69ae2 100644
--- a/scripts/Makefile.fwinst
+++ b/scripts/Makefile.fwinst
@@ -42,7 +42,7 @@
 $(installed-fw-dirs):
 	$(call cmd,mkdir)
 
-$(installed-fw): $(INSTALL_FW_PATH)/%: $(obj)/% | $(INSTALL_FW_PATH)/$$(dir %)
+$(installed-fw): $(INSTALL_FW_PATH)/%: $(obj)/% | $$(dir $(INSTALL_FW_PATH)/%)
 	$(call cmd,install)
 
 PHONY +=  __fw_install __fw_modinst FORCE
diff --git a/scripts/link-vmlinux.sh b/scripts/link-vmlinux.sh
index 4629038c..b3d907e 100644
--- a/scripts/link-vmlinux.sh
+++ b/scripts/link-vmlinux.sh
@@ -74,8 +74,13 @@
 	info KSYM ${2}
 	local kallsymopt;
 
+	if [ -n "${CONFIG_SYMBOL_PREFIX}" ]; then
+		kallsymopt="${kallsymopt} \
+			    --symbol-prefix=${CONFIG_SYMBOL_PREFIX}"
+	fi
+
 	if [ -n "${CONFIG_KALLSYMS_ALL}" ]; then
-		kallsymopt=--all-symbols
+		kallsymopt="${kallsymopt} --all-symbols"
 	fi
 
 	local aflags="${KBUILD_AFLAGS} ${KBUILD_AFLAGS_KERNEL}               \
@@ -211,7 +216,7 @@
 
 	if ! cmp -s System.map .tmp_System.map; then
 		echo >&2 Inconsistent kallsyms data
-		echo >&2 echo Try "make KALLSYMS_EXTRA_PASS=1" as a workaround
+		echo >&2 Try "make KALLSYMS_EXTRA_PASS=1" as a workaround
 		cleanup
 		exit 1
 	fi
diff --git a/sound/core/compress_offload.c b/sound/core/compress_offload.c
index ec2118d..eb60cb8 100644
--- a/sound/core/compress_offload.c
+++ b/sound/core/compress_offload.c
@@ -80,14 +80,12 @@
 	int maj = imajor(inode);
 	int ret;
 
-	if (f->f_flags & O_WRONLY)
+	if ((f->f_flags & O_ACCMODE) == O_WRONLY)
 		dirn = SND_COMPRESS_PLAYBACK;
-	else if (f->f_flags & O_RDONLY)
+	else if ((f->f_flags & O_ACCMODE) == O_RDONLY)
 		dirn = SND_COMPRESS_CAPTURE;
-	else {
-		pr_err("invalid direction\n");
+	else
 		return -EINVAL;
-	}
 
 	if (maj == snd_major)
 		compr = snd_lookup_minor_data(iminor(inode),
diff --git a/sound/pci/hda/hda_codec.c b/sound/pci/hda/hda_codec.c
index f560051..1c65cc5e 100644
--- a/sound/pci/hda/hda_codec.c
+++ b/sound/pci/hda/hda_codec.c
@@ -1209,6 +1209,9 @@
 	kfree(codec);
 }
 
+static bool snd_hda_codec_get_supported_ps(struct hda_codec *codec,
+				hda_nid_t fg, unsigned int power_state);
+
 static void hda_set_power_state(struct hda_codec *codec, hda_nid_t fg,
 				unsigned int power_state);
 
@@ -1317,6 +1320,10 @@
 					   AC_VERB_GET_SUBSYSTEM_ID, 0);
 	}
 
+	codec->epss = snd_hda_codec_get_supported_ps(codec,
+					codec->afg ? codec->afg : codec->mfg,
+					AC_PWRST_EPSS);
+
 	/* power-up all before initialization */
 	hda_set_power_state(codec,
 			    codec->afg ? codec->afg : codec->mfg,
@@ -2346,6 +2353,7 @@
 	}
 	if (codec->patch_ops.free)
 		codec->patch_ops.free(codec);
+	memset(&codec->patch_ops, 0, sizeof(codec->patch_ops));
 	snd_hda_jack_tbl_clear(codec);
 	codec->proc_widget_hook = NULL;
 	codec->spec = NULL;
@@ -2361,7 +2369,6 @@
 	codec->num_pcms = 0;
 	codec->pcm_info = NULL;
 	codec->preset = NULL;
-	memset(&codec->patch_ops, 0, sizeof(codec->patch_ops));
 	codec->slave_dig_outs = NULL;
 	codec->spdif_status_reset = 0;
 	module_put(codec->owner);
@@ -3543,8 +3550,7 @@
 	/* this delay seems necessary to avoid click noise at power-down */
 	if (power_state == AC_PWRST_D3) {
 		/* transition time less than 10ms for power down */
-		bool epss = snd_hda_codec_get_supported_ps(codec, fg, AC_PWRST_EPSS);
-		msleep(epss ? 10 : 100);
+		msleep(codec->epss ? 10 : 100);
 	}
 
 	/* repeat power states setting at most 10 times*/
diff --git a/sound/pci/hda/hda_codec.h b/sound/pci/hda/hda_codec.h
index 7fbc1bc..e5a7e19 100644
--- a/sound/pci/hda/hda_codec.h
+++ b/sound/pci/hda/hda_codec.h
@@ -862,6 +862,7 @@
 	unsigned int ignore_misc_bit:1; /* ignore MISC_NO_PRESENCE bit */
 	unsigned int no_jack_detect:1;	/* Machine has no jack-detection */
 	unsigned int pcm_format_first:1; /* PCM format must be set first */
+	unsigned int epss:1;		/* supporting EPSS? */
 #ifdef CONFIG_SND_HDA_POWER_SAVE
 	unsigned int power_on :1;	/* current (global) power-state */
 	int power_transition;	/* power-state in transition */
diff --git a/sound/pci/hda/hda_intel.c b/sound/pci/hda/hda_intel.c
index 60882c6..228cdf9 100644
--- a/sound/pci/hda/hda_intel.c
+++ b/sound/pci/hda/hda_intel.c
@@ -2701,6 +2701,7 @@
 	SND_PCI_QUIRK(0x1043, 0x813d, "ASUS P5AD2", POS_FIX_LPIB),
 	SND_PCI_QUIRK(0x1043, 0x81b3, "ASUS", POS_FIX_LPIB),
 	SND_PCI_QUIRK(0x1043, 0x81e7, "ASUS M2V", POS_FIX_LPIB),
+	SND_PCI_QUIRK(0x1043, 0x1b43, "ASUS K53E", POS_FIX_POSBUF),
 	SND_PCI_QUIRK(0x104d, 0x9069, "Sony VPCS11V9E", POS_FIX_LPIB),
 	SND_PCI_QUIRK(0x10de, 0xcb89, "Macbook Pro 7,1", POS_FIX_LPIB),
 	SND_PCI_QUIRK(0x1297, 0x3166, "Shuttle", POS_FIX_LPIB),
diff --git a/sound/pci/hda/patch_sigmatel.c b/sound/pci/hda/patch_sigmatel.c
index ea5775a..3d4722f 100644
--- a/sound/pci/hda/patch_sigmatel.c
+++ b/sound/pci/hda/patch_sigmatel.c
@@ -1075,7 +1075,7 @@
 
 static const char * const slave_pfxs[] = {
 	"Front", "Surround", "Center", "LFE", "Side",
-	"Headphone", "Speaker", "IEC958",
+	"Headphone", "Speaker", "IEC958", "PCM",
 	NULL
 };
 
@@ -4543,6 +4543,9 @@
 	struct auto_pin_cfg *cfg = &spec->autocfg;
 	int i;
 
+	if (cfg->speaker_outs == 0)
+		return;
+
 	for (i = 0; i < cfg->line_outs; i++) {
 		if (presence)
 			break;
@@ -5531,6 +5534,7 @@
 		snd_hda_codec_set_pincfg(codec, 0xf, 0x2181205e);
 	}
 
+	codec->epss = 0; /* longer delay needed for D3 */
 	codec->no_trigger_sense = 1;
 	codec->spec = spec;
 
diff --git a/sound/pci/ice1712/prodigy_hifi.c b/sound/pci/ice1712/prodigy_hifi.c
index 764cc93d..075d5aa 100644
--- a/sound/pci/ice1712/prodigy_hifi.c
+++ b/sound/pci/ice1712/prodigy_hifi.c
@@ -297,6 +297,7 @@
 }
 
 static const DECLARE_TLV_DB_SCALE(db_scale_wm_dac, -12700, 100, 1);
+static const DECLARE_TLV_DB_LINEAR(ak4396_db_scale, TLV_DB_GAIN_MUTE, 0);
 
 static struct snd_kcontrol_new prodigy_hd2_controls[] __devinitdata = {
     {
@@ -307,7 +308,7 @@
 	.info = ak4396_dac_vol_info,
 	.get = ak4396_dac_vol_get,
 	.put = ak4396_dac_vol_put,
-	.tlv = { .p = db_scale_wm_dac },
+	.tlv = { .p = ak4396_db_scale },
     },
 };
 
diff --git a/sound/usb/card.c b/sound/usb/card.c
index d5b5c33..4a469f0 100644
--- a/sound/usb/card.c
+++ b/sound/usb/card.c
@@ -553,7 +553,7 @@
 				     struct snd_usb_audio *chip)
 {
 	struct snd_card *card;
-	struct list_head *p;
+	struct list_head *p, *n;
 
 	if (chip == (void *)-1L)
 		return;
@@ -570,7 +570,7 @@
 			snd_usb_stream_disconnect(p);
 		}
 		/* release the endpoint resources */
-		list_for_each(p, &chip->ep_list) {
+		list_for_each_safe(p, n, &chip->ep_list) {
 			snd_usb_endpoint_free(p);
 		}
 		/* release the midi resources */
diff --git a/sound/usb/endpoint.c b/sound/usb/endpoint.c
index c411812..d6e2bb4 100644
--- a/sound/usb/endpoint.c
+++ b/sound/usb/endpoint.c
@@ -141,7 +141,7 @@
  *
  * For implicit feedback, next_packet_size() is unused.
  */
-static int next_packet_size(struct snd_usb_endpoint *ep)
+int snd_usb_endpoint_next_packet_size(struct snd_usb_endpoint *ep)
 {
 	unsigned long flags;
 	int ret;
@@ -177,15 +177,6 @@
 		ep->retire_data_urb(ep->data_subs, urb);
 }
 
-static void prepare_outbound_urb_sizes(struct snd_usb_endpoint *ep,
-				       struct snd_urb_ctx *ctx)
-{
-	int i;
-
-	for (i = 0; i < ctx->packets; ++i)
-		ctx->packet_size[i] = next_packet_size(ep);
-}
-
 /*
  * Prepare a PLAYBACK urb for submission to the bus.
  */
@@ -370,7 +361,6 @@
 			goto exit_clear;
 		}
 
-		prepare_outbound_urb_sizes(ep, ctx);
 		prepare_outbound_urb(ep, ctx);
 	} else {
 		retire_inbound_urb(ep, ctx);
@@ -799,7 +789,9 @@
 /**
  * snd_usb_endpoint_start: start an snd_usb_endpoint
  *
- * @ep: the endpoint to start
+ * @ep:		the endpoint to start
+ * @can_sleep:	flag indicating whether the operation is executed in
+ * 		non-atomic context
  *
  * A call to this function will increment the use count of the endpoint.
  * In case it is not already running, the URBs for this endpoint will be
@@ -809,7 +801,7 @@
  *
  * Returns an error if the URB submission failed, 0 in all other cases.
  */
-int snd_usb_endpoint_start(struct snd_usb_endpoint *ep)
+int snd_usb_endpoint_start(struct snd_usb_endpoint *ep, int can_sleep)
 {
 	int err;
 	unsigned int i;
@@ -821,6 +813,11 @@
 	if (++ep->use_count != 1)
 		return 0;
 
+	/* just to be sure */
+	deactivate_urbs(ep, 0, can_sleep);
+	if (can_sleep)
+		wait_clear_urbs(ep);
+
 	ep->active_mask = 0;
 	ep->unlink_mask = 0;
 	ep->phase = 0;
@@ -850,7 +847,6 @@
 			goto __error;
 
 		if (usb_pipeout(ep->pipe)) {
-			prepare_outbound_urb_sizes(ep, urb->context);
 			prepare_outbound_urb(ep, urb->context);
 		} else {
 			prepare_inbound_urb(ep, urb->context);
diff --git a/sound/usb/endpoint.h b/sound/usb/endpoint.h
index ee2723f..cbbbdf2 100644
--- a/sound/usb/endpoint.h
+++ b/sound/usb/endpoint.h
@@ -13,7 +13,7 @@
 				struct audioformat *fmt,
 				struct snd_usb_endpoint *sync_ep);
 
-int  snd_usb_endpoint_start(struct snd_usb_endpoint *ep);
+int  snd_usb_endpoint_start(struct snd_usb_endpoint *ep, int can_sleep);
 void snd_usb_endpoint_stop(struct snd_usb_endpoint *ep,
 			   int force, int can_sleep, int wait);
 int  snd_usb_endpoint_activate(struct snd_usb_endpoint *ep);
@@ -21,6 +21,7 @@
 void snd_usb_endpoint_free(struct list_head *head);
 
 int snd_usb_endpoint_implict_feedback_sink(struct snd_usb_endpoint *ep);
+int snd_usb_endpoint_next_packet_size(struct snd_usb_endpoint *ep);
 
 void snd_usb_handle_sync_urb(struct snd_usb_endpoint *ep,
 			     struct snd_usb_endpoint *sender,
diff --git a/sound/usb/pcm.c b/sound/usb/pcm.c
index 62ec808..f782ce1 100644
--- a/sound/usb/pcm.c
+++ b/sound/usb/pcm.c
@@ -212,7 +212,7 @@
 	}
 }
 
-static int start_endpoints(struct snd_usb_substream *subs)
+static int start_endpoints(struct snd_usb_substream *subs, int can_sleep)
 {
 	int err;
 
@@ -225,7 +225,7 @@
 		snd_printdd(KERN_DEBUG "Starting data EP @%p\n", ep);
 
 		ep->data_subs = subs;
-		err = snd_usb_endpoint_start(ep);
+		err = snd_usb_endpoint_start(ep, can_sleep);
 		if (err < 0) {
 			clear_bit(SUBSTREAM_FLAG_DATA_EP_STARTED, &subs->flags);
 			return err;
@@ -236,10 +236,25 @@
 	    !test_and_set_bit(SUBSTREAM_FLAG_SYNC_EP_STARTED, &subs->flags)) {
 		struct snd_usb_endpoint *ep = subs->sync_endpoint;
 
+		if (subs->data_endpoint->iface != subs->sync_endpoint->iface ||
+		    subs->data_endpoint->alt_idx != subs->sync_endpoint->alt_idx) {
+			err = usb_set_interface(subs->dev,
+						subs->sync_endpoint->iface,
+						subs->sync_endpoint->alt_idx);
+			if (err < 0) {
+				snd_printk(KERN_ERR
+					   "%d:%d:%d: cannot set interface (%d)\n",
+					   subs->dev->devnum,
+					   subs->sync_endpoint->iface,
+					   subs->sync_endpoint->alt_idx, err);
+				return -EIO;
+			}
+		}
+
 		snd_printdd(KERN_DEBUG "Starting sync EP @%p\n", ep);
 
 		ep->sync_slave = subs->data_endpoint;
-		err = snd_usb_endpoint_start(ep);
+		err = snd_usb_endpoint_start(ep, can_sleep);
 		if (err < 0) {
 			clear_bit(SUBSTREAM_FLAG_SYNC_EP_STARTED, &subs->flags);
 			return err;
@@ -544,13 +559,10 @@
 	subs->last_frame_number = 0;
 	runtime->delay = 0;
 
-	/* clear the pending deactivation on the target EPs */
-	deactivate_endpoints(subs);
-
 	/* for playback, submit the URBs now; otherwise, the first hwptr_done
 	 * updates for all URBs would happen at the same time when starting */
 	if (subs->direction == SNDRV_PCM_STREAM_PLAYBACK)
-		return start_endpoints(subs);
+		return start_endpoints(subs, 1);
 
 	return 0;
 }
@@ -1032,6 +1044,7 @@
 				 struct urb *urb)
 {
 	struct snd_pcm_runtime *runtime = subs->pcm_substream->runtime;
+	struct snd_usb_endpoint *ep = subs->data_endpoint;
 	struct snd_urb_ctx *ctx = urb->context;
 	unsigned int counts, frames, bytes;
 	int i, stride, period_elapsed = 0;
@@ -1043,7 +1056,11 @@
 	urb->number_of_packets = 0;
 	spin_lock_irqsave(&subs->lock, flags);
 	for (i = 0; i < ctx->packets; i++) {
-		counts = ctx->packet_size[i];
+		if (ctx->packet_size[i])
+			counts = ctx->packet_size[i];
+		else
+			counts = snd_usb_endpoint_next_packet_size(ep);
+
 		/* set up descriptor */
 		urb->iso_frame_desc[i].offset = frames * stride;
 		urb->iso_frame_desc[i].length = counts * stride;
@@ -1094,7 +1111,16 @@
 	subs->hwptr_done += bytes;
 	if (subs->hwptr_done >= runtime->buffer_size * stride)
 		subs->hwptr_done -= runtime->buffer_size * stride;
+
+	/* update delay with exact number of samples queued */
+	runtime->delay = subs->last_delay;
 	runtime->delay += frames;
+	subs->last_delay = runtime->delay;
+
+	/* realign last_frame_number */
+	subs->last_frame_number = usb_get_current_frame_number(subs->dev);
+	subs->last_frame_number &= 0xFF; /* keep 8 LSBs */
+
 	spin_unlock_irqrestore(&subs->lock, flags);
 	urb->transfer_buffer_length = bytes;
 	if (period_elapsed)
@@ -1112,12 +1138,32 @@
 	struct snd_pcm_runtime *runtime = subs->pcm_substream->runtime;
 	int stride = runtime->frame_bits >> 3;
 	int processed = urb->transfer_buffer_length / stride;
+	int est_delay;
+
+	/* ignore the delay accounting when procssed=0 is given, i.e.
+	 * silent payloads are procssed before handling the actual data
+	 */
+	if (!processed)
+		return;
 
 	spin_lock_irqsave(&subs->lock, flags);
-	if (processed > runtime->delay)
-		runtime->delay = 0;
+	est_delay = snd_usb_pcm_delay(subs, runtime->rate);
+	/* update delay with exact number of samples played */
+	if (processed > subs->last_delay)
+		subs->last_delay = 0;
 	else
-		runtime->delay -= processed;
+		subs->last_delay -= processed;
+	runtime->delay = subs->last_delay;
+
+	/*
+	 * Report when delay estimate is off by more than 2ms.
+	 * The error should be lower than 2ms since the estimate relies
+	 * on two reads of a counter updated every ms.
+	 */
+	if (abs(est_delay - subs->last_delay) * 1000 > runtime->rate * 2)
+		snd_printk(KERN_DEBUG "delay: estimated %d, actual %d\n",
+			est_delay, subs->last_delay);
+
 	spin_unlock_irqrestore(&subs->lock, flags);
 }
 
@@ -1175,7 +1221,7 @@
 
 	switch (cmd) {
 	case SNDRV_PCM_TRIGGER_START:
-		err = start_endpoints(subs);
+		err = start_endpoints(subs, 0);
 		if (err < 0)
 			return err;