e1000e: add custom set_d[0|3]_lplu_state function pointer for 82574
82574 needs to configure Low Power Link Up (or LPLU) differently than
the other parts in the 8257x family supported by the driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/e1000e/82571.c b/drivers/net/e1000e/82571.c
index 11a273e..cb6c7b1 100644
--- a/drivers/net/e1000e/82571.c
+++ b/drivers/net/e1000e/82571.c
@@ -78,6 +78,8 @@
static void e1000_put_hw_semaphore_82573(struct e1000_hw *hw);
static s32 e1000_get_hw_semaphore_82574(struct e1000_hw *hw);
static void e1000_put_hw_semaphore_82574(struct e1000_hw *hw);
+static s32 e1000_set_d0_lplu_state_82574(struct e1000_hw *hw, bool active);
+static s32 e1000_set_d3_lplu_state_82574(struct e1000_hw *hw, bool active);
/**
* e1000_init_phy_params_82571 - Init PHY func ptrs.
@@ -113,6 +115,8 @@
phy->type = e1000_phy_bm;
phy->ops.acquire = e1000_get_hw_semaphore_82574;
phy->ops.release = e1000_put_hw_semaphore_82574;
+ phy->ops.set_d0_lplu_state = e1000_set_d0_lplu_state_82574;
+ phy->ops.set_d3_lplu_state = e1000_set_d3_lplu_state_82574;
break;
default:
return -E1000_ERR_PHY;
@@ -656,6 +660,58 @@
}
/**
+ * e1000_set_d0_lplu_state_82574 - Set Low Power Linkup D0 state
+ * @hw: pointer to the HW structure
+ * @active: true to enable LPLU, false to disable
+ *
+ * Sets the LPLU D0 state according to the active flag.
+ * LPLU will not be activated unless the
+ * device autonegotiation advertisement meets standards of
+ * either 10 or 10/100 or 10/100/1000 at all duplexes.
+ * This is a function pointer entry point only called by
+ * PHY setup routines.
+ **/
+static s32 e1000_set_d0_lplu_state_82574(struct e1000_hw *hw, bool active)
+{
+ u16 data = er32(POEMB);
+
+ if (active)
+ data |= E1000_PHY_CTRL_D0A_LPLU;
+ else
+ data &= ~E1000_PHY_CTRL_D0A_LPLU;
+
+ ew32(POEMB, data);
+ return 0;
+}
+
+/**
+ * e1000_set_d3_lplu_state_82574 - Sets low power link up state for D3
+ * @hw: pointer to the HW structure
+ * @active: boolean used to enable/disable lplu
+ *
+ * The low power link up (lplu) state is set to the power management level D3
+ * when active is true, else clear lplu for D3. LPLU
+ * is used during Dx states where the power conservation is most important.
+ * During driver activity, SmartSpeed should be enabled so performance is
+ * maintained.
+ **/
+static s32 e1000_set_d3_lplu_state_82574(struct e1000_hw *hw, bool active)
+{
+ u16 data = er32(POEMB);
+
+ if (!active) {
+ data &= ~E1000_PHY_CTRL_NOND0A_LPLU;
+ } else if ((hw->phy.autoneg_advertised == E1000_ALL_SPEED_DUPLEX) ||
+ (hw->phy.autoneg_advertised == E1000_ALL_NOT_GIG) ||
+ (hw->phy.autoneg_advertised == E1000_ALL_10_SPEED)) {
+ data |= E1000_PHY_CTRL_NOND0A_LPLU;
+ }
+
+ ew32(POEMB, data);
+ return 0;
+}
+
+/**
* e1000_acquire_nvm_82571 - Request for access to the EEPROM
* @hw: pointer to the HW structure
*
diff --git a/drivers/net/e1000e/hw.h b/drivers/net/e1000e/hw.h
index ba302a5..e774380 100644
--- a/drivers/net/e1000e/hw.h
+++ b/drivers/net/e1000e/hw.h
@@ -83,6 +83,7 @@
E1000_EXTCNF_CTRL = 0x00F00, /* Extended Configuration Control */
E1000_EXTCNF_SIZE = 0x00F08, /* Extended Configuration Size */
E1000_PHY_CTRL = 0x00F10, /* PHY Control Register in CSR */
+#define E1000_POEMB E1000_PHY_CTRL /* PHY OEM Bits */
E1000_PBA = 0x01000, /* Packet Buffer Allocation - RW */
E1000_PBS = 0x01008, /* Packet Buffer Size */
E1000_EEMNGCTL = 0x01010, /* MNG EEprom Control */