e1000e: concatenate long debug strings which span multiple lines

To ease searching for debug message strings, concatenate strings that span
multiple lines even if the resulting line exceeds 80 columns; these will
not cause checkpatch warnings.

Also, add '\n' and remove unnecessary '\r' from a few debug strings.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
diff --git a/drivers/net/ethernet/intel/e1000e/80003es2lan.c b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
index b3a235c..f323ce5 100644
--- a/drivers/net/ethernet/intel/e1000e/80003es2lan.c
+++ b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
@@ -667,8 +667,7 @@
 	udelay(1);
 
 	if (hw->phy.autoneg_wait_to_complete) {
-		e_dbg("Waiting for forced speed/duplex link "
-			 "on GG82563 phy.\n");
+		e_dbg("Waiting for forced speed/duplex link on GG82563 phy.\n");
 
 		ret_val = e1000e_phy_has_link_generic(hw, PHY_FORCE_LIMIT,
 						     100000, &link);
diff --git a/drivers/net/ethernet/intel/e1000e/ich8lan.c b/drivers/net/ethernet/intel/e1000e/ich8lan.c
index 6a6e6f6..53e5447 100644
--- a/drivers/net/ethernet/intel/e1000e/ich8lan.c
+++ b/drivers/net/ethernet/intel/e1000e/ich8lan.c
@@ -902,8 +902,7 @@
 	}
 
 	if (!timeout) {
-		e_dbg("Failed to acquire the semaphore, FW or HW has it: "
-		      "FWSM=0x%8.8x EXTCNF_CTRL=0x%8.8x)\n",
+		e_dbg("Failed to acquire the semaphore, FW or HW has it: FWSM=0x%8.8x EXTCNF_CTRL=0x%8.8x)\n",
 		      er32(FWSM), extcnf_ctrl);
 		extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG;
 		ew32(EXTCNF_CTRL, extcnf_ctrl);
@@ -2132,8 +2131,7 @@
 
 			return 0;
 		}
-		e_dbg("Unable to determine valid NVM bank via EEC - "
-		       "reading flash signature\n");
+		e_dbg("Unable to determine valid NVM bank via EEC - reading flash signature\n");
 		/* fall-thru */
 	default:
 		/* set bank to 0 in case flash read fails */
@@ -2245,8 +2243,7 @@
 
 	/* Check if the flash descriptor is valid */
 	if (hsfsts.hsf_status.fldesvalid == 0) {
-		e_dbg("Flash descriptor invalid.  "
-			 "SW Sequencing must be used.\n");
+		e_dbg("Flash descriptor invalid.  SW Sequencing must be used.\n");
 		return -E1000_ERR_NVM;
 	}
 
@@ -2446,8 +2443,7 @@
 				/* Repeat for some time before giving up. */
 				continue;
 			} else if (hsfsts.hsf_status.flcdone == 0) {
-				e_dbg("Timeout error - flash cycle "
-					 "did not complete.\n");
+				e_dbg("Timeout error - flash cycle did not complete.\n");
 				break;
 			}
 		}
@@ -2798,8 +2794,7 @@
 			/* Repeat for some time before giving up. */
 			continue;
 		if (hsfsts.hsf_status.flcdone == 0) {
-			e_dbg("Timeout error - flash cycle "
-				 "did not complete.");
+			e_dbg("Timeout error - flash cycle did not complete.\n");
 			break;
 		}
 	} while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT);
diff --git a/drivers/net/ethernet/intel/e1000e/lib.c b/drivers/net/ethernet/intel/e1000e/lib.c
index 78e3f4c..e2678bd 100644
--- a/drivers/net/ethernet/intel/e1000e/lib.c
+++ b/drivers/net/ethernet/intel/e1000e/lib.c
@@ -653,12 +653,10 @@
 			if (rxcw & E1000_RXCW_SYNCH) {
 				if (!(rxcw & E1000_RXCW_IV)) {
 					mac->serdes_has_link = true;
-					e_dbg("SERDES: Link up - autoneg "
-					   "completed successfully.\n");
+					e_dbg("SERDES: Link up - autoneg completed successfully.\n");
 				} else {
 					mac->serdes_has_link = false;
-					e_dbg("SERDES: Link down - invalid"
-					   "codewords detected in autoneg.\n");
+					e_dbg("SERDES: Link down - invalid codewords detected in autoneg.\n");
 				}
 			} else {
 				mac->serdes_has_link = false;
@@ -1118,8 +1116,7 @@
 			return ret_val;
 
 		if (!(mii_status_reg & MII_SR_AUTONEG_COMPLETE)) {
-			e_dbg("Copper PHY and Auto Neg "
-				 "has not completed.\n");
+			e_dbg("Copper PHY and Auto Neg has not completed.\n");
 			return ret_val;
 		}
 
@@ -1183,11 +1180,10 @@
 			 */
 			if (hw->fc.requested_mode == e1000_fc_full) {
 				hw->fc.current_mode = e1000_fc_full;
-				e_dbg("Flow Control = FULL.\r\n");
+				e_dbg("Flow Control = FULL.\n");
 			} else {
 				hw->fc.current_mode = e1000_fc_rx_pause;
-				e_dbg("Flow Control = "
-				      "Rx PAUSE frames only.\r\n");
+				e_dbg("Flow Control = Rx PAUSE frames only.\n");
 			}
 		}
 		/*
@@ -1203,7 +1199,7 @@
 			  (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
 			  (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
 			hw->fc.current_mode = e1000_fc_tx_pause;
-			e_dbg("Flow Control = Tx PAUSE frames only.\r\n");
+			e_dbg("Flow Control = Tx PAUSE frames only.\n");
 		}
 		/*
 		 * For transmitting PAUSE frames ONLY.
@@ -1218,14 +1214,14 @@
 			 !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
 			 (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
 			hw->fc.current_mode = e1000_fc_rx_pause;
-			e_dbg("Flow Control = Rx PAUSE frames only.\r\n");
+			e_dbg("Flow Control = Rx PAUSE frames only.\n");
 		} else {
 			/*
 			 * Per the IEEE spec, at this point flow control
 			 * should be disabled.
 			 */
 			hw->fc.current_mode = e1000_fc_none;
-			e_dbg("Flow Control = NONE.\r\n");
+			e_dbg("Flow Control = NONE.\n");
 		}
 
 		/*
diff --git a/drivers/net/ethernet/intel/e1000e/phy.c b/drivers/net/ethernet/intel/e1000e/phy.c
index 8666476..ed70d08 100644
--- a/drivers/net/ethernet/intel/e1000e/phy.c
+++ b/drivers/net/ethernet/intel/e1000e/phy.c
@@ -1136,8 +1136,7 @@
 	if (phy->autoneg_wait_to_complete) {
 		ret_val = e1000_wait_autoneg(hw);
 		if (ret_val) {
-			e_dbg("Error while waiting for "
-				 "autoneg to complete\n");
+			e_dbg("Error while waiting for autoneg to complete\n");
 			return ret_val;
 		}
 	}