[ARM] 5130/4: Support for the at91sam9g20
Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock
speed.
We created a new board for this device but based the chip support
directly on 9260 files with little updates.
Here is the chip page on Atmel wabsite:
http://atmel.com/dyn/products/product_card.asp?part_id=4337
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index cae5c67..5bad6b9 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -30,6 +30,11 @@
select GENERIC_TIME
select GENERIC_CLOCKEVENTS
+config ARCH_AT91SAM9G20
+ bool "AT91SAM9G20"
+ select GENERIC_TIME
+ select GENERIC_CLOCKEVENTS
+
config ARCH_AT91CAP9
bool "AT91CAP9"
select GENERIC_TIME
@@ -239,6 +244,20 @@
# ----------------------------------------------------------
+if ARCH_AT91SAM9G20
+
+comment "AT91SAM9G20 Board Type"
+
+config MACH_AT91SAM9G20EK
+ bool "Atmel AT91SAM9G20-EK Evaluation Kit"
+ depends on ARCH_AT91SAM9G20
+ help
+ Select this if you are using Atmel's AT91SAM9G20-EK Evaluation Kit.
+
+endif
+
+# ----------------------------------------------------------
+
if ARCH_AT91CAP9
comment "AT91CAP9 Board Type"
@@ -274,13 +293,13 @@
config MTD_AT91_DATAFLASH_CARD
bool "Enable DataFlash Card support"
- depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91CAP9ADK || MACH_SAM9_L9260 || MACH_ECBAT91)
+ depends on (ARCH_AT91RM9200DK || MACH_AT91RM9200EK || MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_ECBAT91 || MACH_SAM9_L9260 || MACH_AT91CAP9ADK)
help
Enable support for the DataFlash card.
config MTD_NAND_AT91_BUSWIDTH_16
bool "Enable 16-bit data bus interface to NAND flash"
- depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91CAP9ADK)
+ depends on (MACH_AT91SAM9260EK || MACH_AT91SAM9261EK || MACH_AT91SAM9263EK || MACH_AT91SAM9G20EK || MACH_AT91CAP9ADK)
help
On AT91SAM926x boards both types of NAND flash can be present
(8 and 16 bit data bus width).
@@ -329,15 +348,15 @@
config AT91_EARLY_USART3
bool "USART3"
- depends on (ARCH_AT91RM9200 || ARCH_AT91SAM9RL || ARCH_AT91SAM9260)
+ depends on (ARCH_AT91RM9200 || ARCH_AT91SAM9RL || ARCH_AT91SAM9260 || ARCH_AT91SAM9G20)
config AT91_EARLY_USART4
bool "USART4"
- depends on ARCH_AT91SAM9260
+ depends on ARCH_AT91SAM9260 || ARCH_AT91SAM9G20
config AT91_EARLY_USART5
bool "USART5"
- depends on ARCH_AT91SAM9260
+ depends on ARCH_AT91SAM9260 || ARCH_AT91SAM9G20
endchoice
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index 932d171..7d641f9 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -15,6 +15,7 @@
obj-$(CONFIG_ARCH_AT91SAM9261) += at91sam9261.o at91sam926x_time.o at91sam9261_devices.o
obj-$(CONFIG_ARCH_AT91SAM9263) += at91sam9263.o at91sam926x_time.o at91sam9263_devices.o
obj-$(CONFIG_ARCH_AT91SAM9RL) += at91sam9rl.o at91sam926x_time.o at91sam9rl_devices.o
+obj-$(CONFIG_ARCH_AT91SAM9G20) += at91sam9260.o at91sam926x_time.o at91sam9260_devices.o
obj-$(CONFIG_ARCH_AT91CAP9) += at91cap9.o at91sam926x_time.o at91cap9_devices.o
obj-$(CONFIG_ARCH_AT91X40) += at91x40.o at91x40_time.o
@@ -49,6 +50,9 @@
# AT91SAM9RL board-specific support
obj-$(CONFIG_MACH_AT91SAM9RLEK) += board-sam9rlek.o
+# AT91SAM9G20 board-specific support
+obj-$(CONFIG_MACH_AT91SAM9G20EK) += board-sam9g20ek.o
+
# AT91CAP9 board-specific support
obj-$(CONFIG_MACH_AT91CAP9ADK) += board-cap9adk.o
diff --git a/arch/arm/mach-at91/at91sam9260.c b/arch/arm/mach-at91/at91sam9260.c
index ee26550..380f12a 100644
--- a/arch/arm/mach-at91/at91sam9260.c
+++ b/arch/arm/mach-at91/at91sam9260.c
@@ -47,6 +47,20 @@
}
};
+static struct map_desc at91sam9g20_sram_desc[] __initdata = {
+ {
+ .virtual = AT91_IO_VIRT_BASE - AT91SAM9G20_SRAM0_SIZE,
+ .pfn = __phys_to_pfn(AT91SAM9G20_SRAM0_BASE),
+ .length = AT91SAM9G20_SRAM0_SIZE,
+ .type = MT_DEVICE,
+ }, {
+ .virtual = AT91_IO_VIRT_BASE - AT91SAM9G20_SRAM0_SIZE - AT91SAM9G20_SRAM1_SIZE,
+ .pfn = __phys_to_pfn(AT91SAM9G20_SRAM1_BASE),
+ .length = AT91SAM9G20_SRAM1_SIZE,
+ .type = MT_DEVICE,
+ }
+};
+
static struct map_desc at91sam9xe_sram_desc[] __initdata = {
{
.pfn = __phys_to_pfn(AT91SAM9XE_SRAM_BASE),
@@ -307,6 +321,8 @@
if (cpu_is_at91sam9xe())
at91sam9xe_initialize();
+ else if (cpu_is_at91sam9g20())
+ iotable_init(at91sam9g20_sram_desc, ARRAY_SIZE(at91sam9g20_sram_desc));
else
iotable_init(at91sam9260_sram_desc, ARRAY_SIZE(at91sam9260_sram_desc));
diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c
index 26f5cac..86cba4a 100644
--- a/arch/arm/mach-at91/at91sam9260_devices.c
+++ b/arch/arm/mach-at91/at91sam9260_devices.c
@@ -18,6 +18,7 @@
#include <asm/arch/board.h>
#include <asm/arch/gpio.h>
+#include <asm/arch/cpu.h>
#include <asm/arch/at91sam9260.h>
#include <asm/arch/at91sam9260_matrix.h>
#include <asm/arch/at91sam9_smc.h>
@@ -320,20 +321,41 @@
csa = at91_sys_read(AT91_MATRIX_EBICSA);
at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
- /* set the bus interface characteristics */
- at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0)
- | AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
+ if (cpu_is_at91sam9260()) {
+ /* Timing for sam9260 */
+ /* set the bus interface characteristics */
+ at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0)
+ | AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
- at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3)
- | AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
+ at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3)
+ | AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
- at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5));
+ at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5));
- if (data->bus_width_16)
- mode = AT91_SMC_DBW_16;
- else
- mode = AT91_SMC_DBW_8;
- at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(2));
+ if (data->bus_width_16)
+ mode = AT91_SMC_DBW_16;
+ else
+ mode = AT91_SMC_DBW_8;
+ at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(2));
+ }
+
+ if (cpu_is_at91sam9g20()) {
+ /* Timing for sam9g20 */
+ /* set the bus interface characteristics */
+ at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0)
+ | AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0));
+
+ at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(4)
+ | AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(4));
+
+ at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(7) | AT91_SMC_NRDCYCLE_(7));
+
+ if (data->bus_width_16)
+ mode = AT91_SMC_DBW_16;
+ else
+ mode = AT91_SMC_DBW_8;
+ at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(3));
+ }
/* enable pin */
if (data->enable_pin)
diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c
new file mode 100644
index 0000000..45617c2
--- /dev/null
+++ b/arch/arm/mach-at91/board-sam9g20ek.c
@@ -0,0 +1,218 @@
+/*
+ * Copyright (C) 2005 SAN People
+ * Copyright (C) 2008 Atmel
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/at73c213.h>
+#include <linux/clk.h>
+
+#include <asm/hardware.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+
+#include "generic.h"
+
+
+static void __init ek_map_io(void)
+{
+ /* Initialize processor: 18.432 MHz crystal */
+ at91sam9260_initialize(18432000);
+
+ /* DGBU on ttyS0. (Rx & Tx only) */
+ at91_register_uart(0, 0, 0);
+
+ /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+ at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+ | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+ | ATMEL_UART_RI);
+
+ /* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+ at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+ /* set serial console to ttyS0 (ie, DBGU) */
+ at91_set_serial_console(0);
+}
+
+static void __init ek_init_irq(void)
+{
+ at91sam9260_init_interrupts(NULL);
+}
+
+
+/*
+ * USB Host port
+ */
+static struct at91_usbh_data __initdata ek_usbh_data = {
+ .ports = 2,
+};
+
+/*
+ * USB Device port
+ */
+static struct at91_udc_data __initdata ek_udc_data = {
+ .vbus_pin = AT91_PIN_PC5,
+ .pullup_pin = 0, /* pull-up driven by UDC */
+};
+
+
+/*
+ * SPI devices.
+ */
+static struct spi_board_info ek_spi_devices[] = {
+#if !defined(CONFIG_MMC_AT91)
+ { /* DataFlash chip */
+ .modalias = "mtd_dataflash",
+ .chip_select = 1,
+ .max_speed_hz = 15 * 1000 * 1000,
+ .bus_num = 0,
+ },
+#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
+ { /* DataFlash card */
+ .modalias = "mtd_dataflash",
+ .chip_select = 0,
+ .max_speed_hz = 15 * 1000 * 1000,
+ .bus_num = 0,
+ },
+#endif
+#endif
+};
+
+
+/*
+ * MACB Ethernet device
+ */
+static struct at91_eth_data __initdata ek_macb_data = {
+ .phy_irq_pin = AT91_PIN_PA7,
+ .is_rmii = 1,
+};
+
+
+/*
+ * NAND flash
+ */
+static struct mtd_partition __initdata ek_nand_partition[] = {
+ {
+ .name = "Bootstrap",
+ .offset = 0,
+ .size = 4 * 1024 * 1024,
+ },
+ {
+ .name = "Partition 1",
+ .offset = 4 * 1024 * 1024,
+ .size = 60 * 1024 * 1024,
+ },
+ {
+ .name = "Partition 2",
+ .offset = 64 * 1024 * 1024,
+ .size = MTDPART_SIZ_FULL,
+ },
+};
+
+static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
+{
+ *num_partitions = ARRAY_SIZE(ek_nand_partition);
+ return ek_nand_partition;
+}
+
+/* det_pin is not connected */
+static struct at91_nand_data __initdata ek_nand_data = {
+ .ale = 21,
+ .cle = 22,
+ .rdy_pin = AT91_PIN_PC13,
+ .enable_pin = AT91_PIN_PC14,
+ .partition_info = nand_partitions,
+#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+ .bus_width_16 = 1,
+#else
+ .bus_width_16 = 0,
+#endif
+};
+
+
+/*
+ * MCI (SD/MMC)
+ * det_pin, wp_pin and vcc_pin are not connected
+ */
+static struct at91_mmc_data __initdata ek_mmc_data = {
+ .slot_b = 1,
+ .wire4 = 1,
+};
+
+
+/*
+ * LEDs
+ */
+static struct gpio_led ek_leds[] = {
+ { /* "bottom" led, green, userled1 to be defined */
+ .name = "ds5",
+ .gpio = AT91_PIN_PA6,
+ .active_low = 1,
+ .default_trigger = "none",
+ },
+ { /* "power" led, yellow */
+ .name = "ds1",
+ .gpio = AT91_PIN_PA9,
+ .default_trigger = "heartbeat",
+ }
+};
+
+static void __init ek_board_init(void)
+{
+ /* Serial */
+ at91_add_device_serial();
+ /* USB Host */
+ at91_add_device_usbh(&ek_usbh_data);
+ /* USB Device */
+ at91_add_device_udc(&ek_udc_data);
+ /* SPI */
+ at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
+ /* NAND */
+ at91_add_device_nand(&ek_nand_data);
+ /* Ethernet */
+ at91_add_device_eth(&ek_macb_data);
+ /* MMC */
+ at91_add_device_mmc(0, &ek_mmc_data);
+ /* I2C */
+ at91_add_device_i2c(NULL, 0);
+ /* LEDs */
+ at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
+}
+
+MACHINE_START(AT91SAM9G20EK, "Atmel AT91SAM9G20-EK")
+ /* Maintainer: Atmel */
+ .phys_io = AT91_BASE_SYS,
+ .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+ .boot_params = AT91_SDRAM_BASE + 0x100,
+ .timer = &at91sam926x_timer,
+ .map_io = ek_map_io,
+ .init_irq = ek_init_irq,
+ .init_machine = ek_board_init,
+MACHINE_END
diff --git a/arch/arm/mach-at91/clock.c b/arch/arm/mach-at91/clock.c
index e8ce8f0..464bdbb 100644
--- a/arch/arm/mach-at91/clock.c
+++ b/arch/arm/mach-at91/clock.c
@@ -515,14 +515,19 @@
/*
* PLL input between 1MHz and 32MHz per spec, but lower
* frequences seem necessary in some cases so allow 100K.
+ * Warning: some newer products need 2MHz min.
*/
input = main_freq / i;
+ if (cpu_is_at91sam9g20() && input < 2000000)
+ continue;
if (input < 100000)
continue;
if (input > 32000000)
continue;
mul1 = out_freq / input;
+ if (cpu_is_at91sam9g20() && mul > 63)
+ continue;
if (mul1 > 2048)
continue;
if (mul1 < 2)
@@ -582,7 +587,8 @@
/* report if PLLA is more than mildly overclocked */
plla.rate_hz = at91_pll_rate(&plla, main_clock, at91_sys_read(AT91_CKGR_PLLAR));
- if (plla.rate_hz > 209000000)
+ if ((!cpu_is_at91sam9g20() && plla.rate_hz > 209000000)
+ || (cpu_is_at91sam9g20() && plla.rate_hz > 800000000))
pr_info("Clocks: PLLA overclocked, %ld MHz\n", plla.rate_hz / 1000000);
/*
@@ -597,7 +603,7 @@
uhpck.pmc_mask = AT91RM9200_PMC_UHP;
udpck.pmc_mask = AT91RM9200_PMC_UDP;
at91_sys_write(AT91_PMC_SCER, AT91RM9200_PMC_MCKUDP);
- } else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263()) {
+ } else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) {
uhpck.pmc_mask = AT91SAM926x_PMC_UHP;
udpck.pmc_mask = AT91SAM926x_PMC_UDP;
} else if (cpu_is_at91cap9()) {
@@ -629,8 +635,13 @@
freq /= (1 << ((mckr & AT91_PMC_PRES) >> 2)); /* prescale */
if (cpu_is_at91rm9200())
mck.rate_hz = freq / (1 + ((mckr & AT91_PMC_MDIV) >> 8)); /* mdiv */
- else
- mck.rate_hz = freq / (1 << ((mckr & AT91_PMC_MDIV) >> 8)); /* mdiv */
+ else if (cpu_is_at91sam9g20()) {
+ mck.rate_hz = (mckr & AT91_PMC_MDIV) ?
+ freq / ((mckr & AT91_PMC_MDIV) >> 7) : freq; /* mdiv ; (x >> 7) = ((x >> 8) * 2) */
+ if (mckr & AT91_PMC_PDIV)
+ freq /= 2; /* processor clock division */
+ } else
+ mck.rate_hz = freq / (1 << ((mckr & AT91_PMC_MDIV) >> 8)); /* mdiv */
/* Register the PMC's standard clocks */
for (i = 0; i < ARRAY_SIZE(standard_pmc_clocks); i++)
diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
index aa863c1..8ab4feb 100644
--- a/arch/arm/mach-at91/pm.c
+++ b/arch/arm/mach-at91/pm.c
@@ -202,7 +202,7 @@
pr_debug("AT91: PM - Suspend-to-RAM with USB still active\n");
return 0;
}
- } else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263()) {
+ } else if (cpu_is_at91sam9260() || cpu_is_at91sam9261() || cpu_is_at91sam9263() || cpu_is_at91sam9g20()) {
if ((scsr & (AT91SAM926x_PMC_UHP | AT91SAM926x_PMC_UDP)) != 0) {
pr_debug("AT91: PM - Suspend-to-RAM with USB still active\n");
return 0;
diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig
index 33ed048..750d895 100644
--- a/arch/arm/mm/Kconfig
+++ b/arch/arm/mm/Kconfig
@@ -180,8 +180,8 @@
# ARM926T
config CPU_ARM926T
bool "Support ARM926T processor"
- depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || MACH_REALVIEW_EB || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91CAP9 || ARCH_NS9XXX || ARCH_DAVINCI
- default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91CAP9 || ARCH_NS9XXX || ARCH_DAVINCI
+ depends on ARCH_INTEGRATOR || ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || MACH_REALVIEW_EB || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91SAM9G20 || ARCH_AT91CAP9 || ARCH_NS9XXX || ARCH_DAVINCI
+ default y if ARCH_VERSATILE_PB || MACH_VERSATILE_AB || ARCH_OMAP730 || ARCH_OMAP16XX || ARCH_PNX4008 || ARCH_NETX || CPU_S3C2412 || ARCH_AT91SAM9260 || ARCH_AT91SAM9261 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91SAM9G20 || ARCH_AT91CAP9 || ARCH_NS9XXX || ARCH_DAVINCI
select CPU_32v5
select CPU_ABRT_EV5TJ
select CPU_PABRT_NOIFAR