Merge branch 'upstream-fixes' into upstream
diff --git a/drivers/scsi/ahci.c b/drivers/scsi/ahci.c
index 904c25f..68fd766 100644
--- a/drivers/scsi/ahci.c
+++ b/drivers/scsi/ahci.c
@@ -92,7 +92,9 @@
HOST_AHCI_EN = (1 << 31), /* AHCI enabled */
/* HOST_CAP bits */
+ HOST_CAP_SSC = (1 << 14), /* Slumber capable */
HOST_CAP_CLO = (1 << 24), /* Command List Override support */
+ HOST_CAP_SSS = (1 << 27), /* Staggered Spin-up */
HOST_CAP_NCQ = (1 << 30), /* Native Command Queueing */
HOST_CAP_64 = (1 << 31), /* PCI DAC (64-bit DMA) support */
@@ -155,6 +157,7 @@
PORT_CMD_SPIN_UP = (1 << 1), /* Spin up device */
PORT_CMD_START = (1 << 0), /* Enable port DMA engine */
+ PORT_CMD_ICC_MASK = (0xf << 28), /* i/f ICC state mask */
PORT_CMD_ICC_ACTIVE = (0x1 << 28), /* Put i/f in active state */
PORT_CMD_ICC_PARTIAL = (0x2 << 28), /* Put i/f in partial state */
PORT_CMD_ICC_SLUMBER = (0x6 << 28), /* Put i/f in slumber state */
@@ -212,6 +215,10 @@
static void ahci_thaw(struct ata_port *ap);
static void ahci_error_handler(struct ata_port *ap);
static void ahci_post_internal_cmd(struct ata_queued_cmd *qc);
+static int ahci_port_suspend(struct ata_port *ap, pm_message_t mesg);
+static int ahci_port_resume(struct ata_port *ap);
+static int ahci_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg);
+static int ahci_pci_device_resume(struct pci_dev *pdev);
static void ahci_remove_one (struct pci_dev *pdev);
static struct scsi_host_template ahci_sht = {
@@ -231,6 +238,8 @@
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
+ .suspend = ata_scsi_device_suspend,
+ .resume = ata_scsi_device_resume,
};
static const struct ata_port_operations ahci_ops = {
@@ -257,6 +266,9 @@
.error_handler = ahci_error_handler,
.post_internal_cmd = ahci_post_internal_cmd,
+ .port_suspend = ahci_port_suspend,
+ .port_resume = ahci_port_resume,
+
.port_start = ahci_port_start,
.port_stop = ahci_port_stop,
};
@@ -350,6 +362,14 @@
{ PCI_VENDOR_ID_NVIDIA, 0x044f, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
board_ahci }, /* MCP65 */
+ /* SiS */
+ { PCI_VENDOR_ID_SI, 0x1184, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ board_ahci }, /* SiS 966 */
+ { PCI_VENDOR_ID_SI, 0x1185, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ board_ahci }, /* SiS 966 */
+ { PCI_VENDOR_ID_SI, 0x0186, PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ board_ahci }, /* SiS 968 */
+
{ } /* terminate list */
};
@@ -358,6 +378,8 @@
.name = DRV_NAME,
.id_table = ahci_pci_tbl,
.probe = ahci_init_one,
+ .suspend = ahci_pci_device_suspend,
+ .resume = ahci_pci_device_resume,
.remove = ahci_remove_one,
};
@@ -372,108 +394,6 @@
return (void __iomem *) ahci_port_base_ul((unsigned long)base, port);
}
-static int ahci_port_start(struct ata_port *ap)
-{
- struct device *dev = ap->host_set->dev;
- struct ahci_host_priv *hpriv = ap->host_set->private_data;
- struct ahci_port_priv *pp;
- void __iomem *mmio = ap->host_set->mmio_base;
- void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
- void *mem;
- dma_addr_t mem_dma;
- int rc;
-
- pp = kmalloc(sizeof(*pp), GFP_KERNEL);
- if (!pp)
- return -ENOMEM;
- memset(pp, 0, sizeof(*pp));
-
- rc = ata_pad_alloc(ap, dev);
- if (rc) {
- kfree(pp);
- return rc;
- }
-
- mem = dma_alloc_coherent(dev, AHCI_PORT_PRIV_DMA_SZ, &mem_dma, GFP_KERNEL);
- if (!mem) {
- ata_pad_free(ap, dev);
- kfree(pp);
- return -ENOMEM;
- }
- memset(mem, 0, AHCI_PORT_PRIV_DMA_SZ);
-
- /*
- * First item in chunk of DMA memory: 32-slot command table,
- * 32 bytes each in size
- */
- pp->cmd_slot = mem;
- pp->cmd_slot_dma = mem_dma;
-
- mem += AHCI_CMD_SLOT_SZ;
- mem_dma += AHCI_CMD_SLOT_SZ;
-
- /*
- * Second item: Received-FIS area
- */
- pp->rx_fis = mem;
- pp->rx_fis_dma = mem_dma;
-
- mem += AHCI_RX_FIS_SZ;
- mem_dma += AHCI_RX_FIS_SZ;
-
- /*
- * Third item: data area for storing a single command
- * and its scatter-gather table
- */
- pp->cmd_tbl = mem;
- pp->cmd_tbl_dma = mem_dma;
-
- ap->private_data = pp;
-
- if (hpriv->cap & HOST_CAP_64)
- writel((pp->cmd_slot_dma >> 16) >> 16, port_mmio + PORT_LST_ADDR_HI);
- writel(pp->cmd_slot_dma & 0xffffffff, port_mmio + PORT_LST_ADDR);
- readl(port_mmio + PORT_LST_ADDR); /* flush */
-
- if (hpriv->cap & HOST_CAP_64)
- writel((pp->rx_fis_dma >> 16) >> 16, port_mmio + PORT_FIS_ADDR_HI);
- writel(pp->rx_fis_dma & 0xffffffff, port_mmio + PORT_FIS_ADDR);
- readl(port_mmio + PORT_FIS_ADDR); /* flush */
-
- writel(PORT_CMD_ICC_ACTIVE | PORT_CMD_FIS_RX |
- PORT_CMD_POWER_ON | PORT_CMD_SPIN_UP |
- PORT_CMD_START, port_mmio + PORT_CMD);
- readl(port_mmio + PORT_CMD); /* flush */
-
- return 0;
-}
-
-
-static void ahci_port_stop(struct ata_port *ap)
-{
- struct device *dev = ap->host_set->dev;
- struct ahci_port_priv *pp = ap->private_data;
- void __iomem *mmio = ap->host_set->mmio_base;
- void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
- u32 tmp;
-
- tmp = readl(port_mmio + PORT_CMD);
- tmp &= ~(PORT_CMD_START | PORT_CMD_FIS_RX);
- writel(tmp, port_mmio + PORT_CMD);
- readl(port_mmio + PORT_CMD); /* flush */
-
- /* spec says 500 msecs for each PORT_CMD_{START,FIS_RX} bit, so
- * this is slightly incorrect.
- */
- msleep(500);
-
- ap->private_data = NULL;
- dma_free_coherent(dev, AHCI_PORT_PRIV_DMA_SZ,
- pp->cmd_slot, pp->cmd_slot_dma);
- ata_pad_free(ap, dev);
- kfree(pp);
-}
-
static u32 ahci_scr_read (struct ata_port *ap, unsigned int sc_reg_in)
{
unsigned int sc_reg;
@@ -508,43 +428,256 @@
writel(val, (void __iomem *) ap->ioaddr.scr_addr + (sc_reg * 4));
}
-static int ahci_stop_engine(struct ata_port *ap)
+static void ahci_start_engine(void __iomem *port_mmio)
{
- void __iomem *mmio = ap->host_set->mmio_base;
- void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
- int work;
u32 tmp;
- tmp = readl(port_mmio + PORT_CMD);
- tmp &= ~PORT_CMD_START;
- writel(tmp, port_mmio + PORT_CMD);
-
- /* wait for engine to stop. TODO: this could be
- * as long as 500 msec
- */
- work = 1000;
- while (work-- > 0) {
- tmp = readl(port_mmio + PORT_CMD);
- if ((tmp & PORT_CMD_LIST_ON) == 0)
- return 0;
- udelay(10);
- }
-
- return -EIO;
-}
-
-static void ahci_start_engine(struct ata_port *ap)
-{
- void __iomem *mmio = ap->host_set->mmio_base;
- void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
- u32 tmp;
-
+ /* start DMA */
tmp = readl(port_mmio + PORT_CMD);
tmp |= PORT_CMD_START;
writel(tmp, port_mmio + PORT_CMD);
readl(port_mmio + PORT_CMD); /* flush */
}
+static int ahci_stop_engine(void __iomem *port_mmio)
+{
+ u32 tmp;
+
+ tmp = readl(port_mmio + PORT_CMD);
+
+ /* check if the HBA is idle */
+ if ((tmp & (PORT_CMD_START | PORT_CMD_LIST_ON)) == 0)
+ return 0;
+
+ /* setting HBA to idle */
+ tmp &= ~PORT_CMD_START;
+ writel(tmp, port_mmio + PORT_CMD);
+
+ /* wait for engine to stop. This could be as long as 500 msec */
+ tmp = ata_wait_register(port_mmio + PORT_CMD,
+ PORT_CMD_LIST_ON, PORT_CMD_LIST_ON, 1, 500);
+ if (tmp & PORT_CMD_LIST_ON)
+ return -EIO;
+
+ return 0;
+}
+
+static void ahci_start_fis_rx(void __iomem *port_mmio, u32 cap,
+ dma_addr_t cmd_slot_dma, dma_addr_t rx_fis_dma)
+{
+ u32 tmp;
+
+ /* set FIS registers */
+ if (cap & HOST_CAP_64)
+ writel((cmd_slot_dma >> 16) >> 16, port_mmio + PORT_LST_ADDR_HI);
+ writel(cmd_slot_dma & 0xffffffff, port_mmio + PORT_LST_ADDR);
+
+ if (cap & HOST_CAP_64)
+ writel((rx_fis_dma >> 16) >> 16, port_mmio + PORT_FIS_ADDR_HI);
+ writel(rx_fis_dma & 0xffffffff, port_mmio + PORT_FIS_ADDR);
+
+ /* enable FIS reception */
+ tmp = readl(port_mmio + PORT_CMD);
+ tmp |= PORT_CMD_FIS_RX;
+ writel(tmp, port_mmio + PORT_CMD);
+
+ /* flush */
+ readl(port_mmio + PORT_CMD);
+}
+
+static int ahci_stop_fis_rx(void __iomem *port_mmio)
+{
+ u32 tmp;
+
+ /* disable FIS reception */
+ tmp = readl(port_mmio + PORT_CMD);
+ tmp &= ~PORT_CMD_FIS_RX;
+ writel(tmp, port_mmio + PORT_CMD);
+
+ /* wait for completion, spec says 500ms, give it 1000 */
+ tmp = ata_wait_register(port_mmio + PORT_CMD, PORT_CMD_FIS_ON,
+ PORT_CMD_FIS_ON, 10, 1000);
+ if (tmp & PORT_CMD_FIS_ON)
+ return -EBUSY;
+
+ return 0;
+}
+
+static void ahci_power_up(void __iomem *port_mmio, u32 cap)
+{
+ u32 cmd;
+
+ cmd = readl(port_mmio + PORT_CMD) & ~PORT_CMD_ICC_MASK;
+
+ /* spin up device */
+ if (cap & HOST_CAP_SSS) {
+ cmd |= PORT_CMD_SPIN_UP;
+ writel(cmd, port_mmio + PORT_CMD);
+ }
+
+ /* wake up link */
+ writel(cmd | PORT_CMD_ICC_ACTIVE, port_mmio + PORT_CMD);
+}
+
+static void ahci_power_down(void __iomem *port_mmio, u32 cap)
+{
+ u32 cmd, scontrol;
+
+ cmd = readl(port_mmio + PORT_CMD) & ~PORT_CMD_ICC_MASK;
+
+ if (cap & HOST_CAP_SSC) {
+ /* enable transitions to slumber mode */
+ scontrol = readl(port_mmio + PORT_SCR_CTL);
+ if ((scontrol & 0x0f00) > 0x100) {
+ scontrol &= ~0xf00;
+ writel(scontrol, port_mmio + PORT_SCR_CTL);
+ }
+
+ /* put device into slumber mode */
+ writel(cmd | PORT_CMD_ICC_SLUMBER, port_mmio + PORT_CMD);
+
+ /* wait for the transition to complete */
+ ata_wait_register(port_mmio + PORT_CMD, PORT_CMD_ICC_SLUMBER,
+ PORT_CMD_ICC_SLUMBER, 1, 50);
+ }
+
+ /* put device into listen mode */
+ if (cap & HOST_CAP_SSS) {
+ /* first set PxSCTL.DET to 0 */
+ scontrol = readl(port_mmio + PORT_SCR_CTL);
+ scontrol &= ~0xf;
+ writel(scontrol, port_mmio + PORT_SCR_CTL);
+
+ /* then set PxCMD.SUD to 0 */
+ cmd &= ~PORT_CMD_SPIN_UP;
+ writel(cmd, port_mmio + PORT_CMD);
+ }
+}
+
+static void ahci_init_port(void __iomem *port_mmio, u32 cap,
+ dma_addr_t cmd_slot_dma, dma_addr_t rx_fis_dma)
+{
+ /* power up */
+ ahci_power_up(port_mmio, cap);
+
+ /* enable FIS reception */
+ ahci_start_fis_rx(port_mmio, cap, cmd_slot_dma, rx_fis_dma);
+
+ /* enable DMA */
+ ahci_start_engine(port_mmio);
+}
+
+static int ahci_deinit_port(void __iomem *port_mmio, u32 cap, const char **emsg)
+{
+ int rc;
+
+ /* disable DMA */
+ rc = ahci_stop_engine(port_mmio);
+ if (rc) {
+ *emsg = "failed to stop engine";
+ return rc;
+ }
+
+ /* disable FIS reception */
+ rc = ahci_stop_fis_rx(port_mmio);
+ if (rc) {
+ *emsg = "failed stop FIS RX";
+ return rc;
+ }
+
+ /* put device into slumber mode */
+ ahci_power_down(port_mmio, cap);
+
+ return 0;
+}
+
+static int ahci_reset_controller(void __iomem *mmio, struct pci_dev *pdev)
+{
+ u32 cap_save, tmp;
+
+ cap_save = readl(mmio + HOST_CAP);
+ cap_save &= ( (1<<28) | (1<<17) );
+ cap_save |= (1 << 27);
+
+ /* global controller reset */
+ tmp = readl(mmio + HOST_CTL);
+ if ((tmp & HOST_RESET) == 0) {
+ writel(tmp | HOST_RESET, mmio + HOST_CTL);
+ readl(mmio + HOST_CTL); /* flush */
+ }
+
+ /* reset must complete within 1 second, or
+ * the hardware should be considered fried.
+ */
+ ssleep(1);
+
+ tmp = readl(mmio + HOST_CTL);
+ if (tmp & HOST_RESET) {
+ dev_printk(KERN_ERR, &pdev->dev,
+ "controller reset failed (0x%x)\n", tmp);
+ return -EIO;
+ }
+
+ writel(HOST_AHCI_EN, mmio + HOST_CTL);
+ (void) readl(mmio + HOST_CTL); /* flush */
+ writel(cap_save, mmio + HOST_CAP);
+ writel(0xf, mmio + HOST_PORTS_IMPL);
+ (void) readl(mmio + HOST_PORTS_IMPL); /* flush */
+
+ if (pdev->vendor == PCI_VENDOR_ID_INTEL) {
+ u16 tmp16;
+
+ /* configure PCS */
+ pci_read_config_word(pdev, 0x92, &tmp16);
+ tmp16 |= 0xf;
+ pci_write_config_word(pdev, 0x92, tmp16);
+ }
+
+ return 0;
+}
+
+static void ahci_init_controller(void __iomem *mmio, struct pci_dev *pdev,
+ int n_ports, u32 cap)
+{
+ int i, rc;
+ u32 tmp;
+
+ for (i = 0; i < n_ports; i++) {
+ void __iomem *port_mmio = ahci_port_base(mmio, i);
+ const char *emsg = NULL;
+
+#if 0 /* BIOSen initialize this incorrectly */
+ if (!(hpriv->port_map & (1 << i)))
+ continue;
+#endif
+
+ /* make sure port is not active */
+ rc = ahci_deinit_port(port_mmio, cap, &emsg);
+ if (rc)
+ dev_printk(KERN_WARNING, &pdev->dev,
+ "%s (%d)\n", emsg, rc);
+
+ /* clear SError */
+ tmp = readl(port_mmio + PORT_SCR_ERR);
+ VPRINTK("PORT_SCR_ERR 0x%x\n", tmp);
+ writel(tmp, port_mmio + PORT_SCR_ERR);
+
+ /* clear port IRQ */
+ tmp = readl(port_mmio + PORT_IRQ_STAT);
+ VPRINTK("PORT_IRQ_STAT 0x%x\n", tmp);
+ if (tmp)
+ writel(tmp, port_mmio + PORT_IRQ_STAT);
+
+ writel(1 << i, mmio + HOST_IRQ_STAT);
+ }
+
+ tmp = readl(mmio + HOST_CTL);
+ VPRINTK("HOST_CTL 0x%x\n", tmp);
+ writel(tmp | HOST_IRQ_EN, mmio + HOST_CTL);
+ tmp = readl(mmio + HOST_CTL);
+ VPRINTK("HOST_CTL 0x%x\n", tmp);
+}
+
static unsigned int ahci_dev_classify(struct ata_port *ap)
{
void __iomem *port_mmio = (void __iomem *) ap->ioaddr.cmd_addr;
@@ -626,7 +759,7 @@
}
/* prepare for SRST (AHCI-1.1 10.4.1) */
- rc = ahci_stop_engine(ap);
+ rc = ahci_stop_engine(port_mmio);
if (rc) {
reason = "failed to stop engine";
goto fail_restart;
@@ -647,7 +780,7 @@
}
/* restart engine */
- ahci_start_engine(ap);
+ ahci_start_engine(port_mmio);
ata_tf_init(ap->device, &tf);
fis = pp->cmd_tbl;
@@ -706,7 +839,7 @@
return 0;
fail_restart:
- ahci_start_engine(ap);
+ ahci_start_engine(port_mmio);
fail:
ata_port_printk(ap, KERN_ERR, "softreset failed (%s)\n", reason);
return rc;
@@ -717,11 +850,13 @@
struct ahci_port_priv *pp = ap->private_data;
u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
struct ata_taskfile tf;
+ void __iomem *mmio = ap->host_set->mmio_base;
+ void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
int rc;
DPRINTK("ENTER\n");
- ahci_stop_engine(ap);
+ ahci_stop_engine(port_mmio);
/* clear D2H reception area to properly wait for D2H FIS */
ata_tf_init(ap->device, &tf);
@@ -730,7 +865,7 @@
rc = sata_std_hardreset(ap, class);
- ahci_start_engine(ap);
+ ahci_start_engine(port_mmio);
if (rc == 0 && ata_port_online(ap))
*class = ahci_dev_classify(ap);
@@ -1046,10 +1181,13 @@
static void ahci_error_handler(struct ata_port *ap)
{
+ void __iomem *mmio = ap->host_set->mmio_base;
+ void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
+
if (!(ap->pflags & ATA_PFLAG_FROZEN)) {
/* restart engine */
- ahci_stop_engine(ap);
- ahci_start_engine(ap);
+ ahci_stop_engine(port_mmio);
+ ahci_start_engine(port_mmio);
}
/* perform recovery */
@@ -1060,17 +1198,178 @@
static void ahci_post_internal_cmd(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
+ void __iomem *mmio = ap->host_set->mmio_base;
+ void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
if (qc->flags & ATA_QCFLAG_FAILED)
qc->err_mask |= AC_ERR_OTHER;
if (qc->err_mask) {
/* make DMA engine forget about the failed command */
- ahci_stop_engine(ap);
- ahci_start_engine(ap);
+ ahci_stop_engine(port_mmio);
+ ahci_start_engine(port_mmio);
}
}
+static int ahci_port_suspend(struct ata_port *ap, pm_message_t mesg)
+{
+ struct ahci_host_priv *hpriv = ap->host_set->private_data;
+ struct ahci_port_priv *pp = ap->private_data;
+ void __iomem *mmio = ap->host_set->mmio_base;
+ void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
+ const char *emsg = NULL;
+ int rc;
+
+ rc = ahci_deinit_port(port_mmio, hpriv->cap, &emsg);
+ if (rc) {
+ ata_port_printk(ap, KERN_ERR, "%s (%d)\n", emsg, rc);
+ ahci_init_port(port_mmio, hpriv->cap,
+ pp->cmd_slot_dma, pp->rx_fis_dma);
+ }
+
+ return rc;
+}
+
+static int ahci_port_resume(struct ata_port *ap)
+{
+ struct ahci_port_priv *pp = ap->private_data;
+ struct ahci_host_priv *hpriv = ap->host_set->private_data;
+ void __iomem *mmio = ap->host_set->mmio_base;
+ void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
+
+ ahci_init_port(port_mmio, hpriv->cap, pp->cmd_slot_dma, pp->rx_fis_dma);
+
+ return 0;
+}
+
+static int ahci_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
+{
+ struct ata_host_set *host_set = dev_get_drvdata(&pdev->dev);
+ void __iomem *mmio = host_set->mmio_base;
+ u32 ctl;
+
+ if (mesg.event == PM_EVENT_SUSPEND) {
+ /* AHCI spec rev1.1 section 8.3.3:
+ * Software must disable interrupts prior to requesting a
+ * transition of the HBA to D3 state.
+ */
+ ctl = readl(mmio + HOST_CTL);
+ ctl &= ~HOST_IRQ_EN;
+ writel(ctl, mmio + HOST_CTL);
+ readl(mmio + HOST_CTL); /* flush */
+ }
+
+ return ata_pci_device_suspend(pdev, mesg);
+}
+
+static int ahci_pci_device_resume(struct pci_dev *pdev)
+{
+ struct ata_host_set *host_set = dev_get_drvdata(&pdev->dev);
+ struct ahci_host_priv *hpriv = host_set->private_data;
+ void __iomem *mmio = host_set->mmio_base;
+ int rc;
+
+ ata_pci_device_do_resume(pdev);
+
+ if (pdev->dev.power.power_state.event == PM_EVENT_SUSPEND) {
+ rc = ahci_reset_controller(mmio, pdev);
+ if (rc)
+ return rc;
+
+ ahci_init_controller(mmio, pdev, host_set->n_ports, hpriv->cap);
+ }
+
+ ata_host_set_resume(host_set);
+
+ return 0;
+}
+
+static int ahci_port_start(struct ata_port *ap)
+{
+ struct device *dev = ap->host_set->dev;
+ struct ahci_host_priv *hpriv = ap->host_set->private_data;
+ struct ahci_port_priv *pp;
+ void __iomem *mmio = ap->host_set->mmio_base;
+ void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
+ void *mem;
+ dma_addr_t mem_dma;
+ int rc;
+
+ pp = kmalloc(sizeof(*pp), GFP_KERNEL);
+ if (!pp)
+ return -ENOMEM;
+ memset(pp, 0, sizeof(*pp));
+
+ rc = ata_pad_alloc(ap, dev);
+ if (rc) {
+ kfree(pp);
+ return rc;
+ }
+
+ mem = dma_alloc_coherent(dev, AHCI_PORT_PRIV_DMA_SZ, &mem_dma, GFP_KERNEL);
+ if (!mem) {
+ ata_pad_free(ap, dev);
+ kfree(pp);
+ return -ENOMEM;
+ }
+ memset(mem, 0, AHCI_PORT_PRIV_DMA_SZ);
+
+ /*
+ * First item in chunk of DMA memory: 32-slot command table,
+ * 32 bytes each in size
+ */
+ pp->cmd_slot = mem;
+ pp->cmd_slot_dma = mem_dma;
+
+ mem += AHCI_CMD_SLOT_SZ;
+ mem_dma += AHCI_CMD_SLOT_SZ;
+
+ /*
+ * Second item: Received-FIS area
+ */
+ pp->rx_fis = mem;
+ pp->rx_fis_dma = mem_dma;
+
+ mem += AHCI_RX_FIS_SZ;
+ mem_dma += AHCI_RX_FIS_SZ;
+
+ /*
+ * Third item: data area for storing a single command
+ * and its scatter-gather table
+ */
+ pp->cmd_tbl = mem;
+ pp->cmd_tbl_dma = mem_dma;
+
+ ap->private_data = pp;
+
+ /* initialize port */
+ ahci_init_port(port_mmio, hpriv->cap, pp->cmd_slot_dma, pp->rx_fis_dma);
+
+ return 0;
+}
+
+static void ahci_port_stop(struct ata_port *ap)
+{
+ struct device *dev = ap->host_set->dev;
+ struct ahci_host_priv *hpriv = ap->host_set->private_data;
+ struct ahci_port_priv *pp = ap->private_data;
+ void __iomem *mmio = ap->host_set->mmio_base;
+ void __iomem *port_mmio = ahci_port_base(mmio, ap->port_no);
+ const char *emsg = NULL;
+ int rc;
+
+ /* de-initialize port */
+ rc = ahci_deinit_port(port_mmio, hpriv->cap, &emsg);
+ if (rc)
+ ata_port_printk(ap, KERN_WARNING, "%s (%d)\n", emsg, rc);
+
+ ap->private_data = NULL;
+ dma_free_coherent(dev, AHCI_PORT_PRIV_DMA_SZ,
+ pp->cmd_slot, pp->cmd_slot_dma);
+ ata_pad_free(ap, dev);
+ kfree(pp);
+}
+
static void ahci_setup_port(struct ata_ioports *port, unsigned long base,
unsigned int port_idx)
{
@@ -1089,47 +1388,12 @@
struct ahci_host_priv *hpriv = probe_ent->private_data;
struct pci_dev *pdev = to_pci_dev(probe_ent->dev);
void __iomem *mmio = probe_ent->mmio_base;
- u32 tmp, cap_save;
- unsigned int i, j, using_dac;
+ unsigned int i, using_dac;
int rc;
- void __iomem *port_mmio;
- cap_save = readl(mmio + HOST_CAP);
- cap_save &= ( (1<<28) | (1<<17) );
- cap_save |= (1 << 27);
-
- /* global controller reset */
- tmp = readl(mmio + HOST_CTL);
- if ((tmp & HOST_RESET) == 0) {
- writel(tmp | HOST_RESET, mmio + HOST_CTL);
- readl(mmio + HOST_CTL); /* flush */
- }
-
- /* reset must complete within 1 second, or
- * the hardware should be considered fried.
- */
- ssleep(1);
-
- tmp = readl(mmio + HOST_CTL);
- if (tmp & HOST_RESET) {
- dev_printk(KERN_ERR, &pdev->dev,
- "controller reset failed (0x%x)\n", tmp);
- return -EIO;
- }
-
- writel(HOST_AHCI_EN, mmio + HOST_CTL);
- (void) readl(mmio + HOST_CTL); /* flush */
- writel(cap_save, mmio + HOST_CAP);
- writel(0xf, mmio + HOST_PORTS_IMPL);
- (void) readl(mmio + HOST_PORTS_IMPL); /* flush */
-
- if (pdev->vendor == PCI_VENDOR_ID_INTEL) {
- u16 tmp16;
-
- pci_read_config_word(pdev, 0x92, &tmp16);
- tmp16 |= 0xf;
- pci_write_config_word(pdev, 0x92, tmp16);
- }
+ rc = ahci_reset_controller(mmio, pdev);
+ if (rc)
+ return rc;
hpriv->cap = readl(mmio + HOST_CAP);
hpriv->port_map = readl(mmio + HOST_PORTS_IMPL);
@@ -1165,63 +1429,10 @@
}
}
- for (i = 0; i < probe_ent->n_ports; i++) {
-#if 0 /* BIOSen initialize this incorrectly */
- if (!(hpriv->port_map & (1 << i)))
- continue;
-#endif
+ for (i = 0; i < probe_ent->n_ports; i++)
+ ahci_setup_port(&probe_ent->port[i], (unsigned long) mmio, i);
- port_mmio = ahci_port_base(mmio, i);
- VPRINTK("mmio %p port_mmio %p\n", mmio, port_mmio);
-
- ahci_setup_port(&probe_ent->port[i],
- (unsigned long) mmio, i);
-
- /* make sure port is not active */
- tmp = readl(port_mmio + PORT_CMD);
- VPRINTK("PORT_CMD 0x%x\n", tmp);
- if (tmp & (PORT_CMD_LIST_ON | PORT_CMD_FIS_ON |
- PORT_CMD_FIS_RX | PORT_CMD_START)) {
- tmp &= ~(PORT_CMD_LIST_ON | PORT_CMD_FIS_ON |
- PORT_CMD_FIS_RX | PORT_CMD_START);
- writel(tmp, port_mmio + PORT_CMD);
- readl(port_mmio + PORT_CMD); /* flush */
-
- /* spec says 500 msecs for each bit, so
- * this is slightly incorrect.
- */
- msleep(500);
- }
-
- writel(PORT_CMD_SPIN_UP, port_mmio + PORT_CMD);
-
- j = 0;
- while (j < 100) {
- msleep(10);
- tmp = readl(port_mmio + PORT_SCR_STAT);
- if ((tmp & 0xf) == 0x3)
- break;
- j++;
- }
-
- tmp = readl(port_mmio + PORT_SCR_ERR);
- VPRINTK("PORT_SCR_ERR 0x%x\n", tmp);
- writel(tmp, port_mmio + PORT_SCR_ERR);
-
- /* ack any pending irq events for this port */
- tmp = readl(port_mmio + PORT_IRQ_STAT);
- VPRINTK("PORT_IRQ_STAT 0x%x\n", tmp);
- if (tmp)
- writel(tmp, port_mmio + PORT_IRQ_STAT);
-
- writel(1 << i, mmio + HOST_IRQ_STAT);
- }
-
- tmp = readl(mmio + HOST_CTL);
- VPRINTK("HOST_CTL 0x%x\n", tmp);
- writel(tmp | HOST_IRQ_EN, mmio + HOST_CTL);
- tmp = readl(mmio + HOST_CTL);
- VPRINTK("HOST_CTL 0x%x\n", tmp);
+ ahci_init_controller(mmio, pdev, probe_ent->n_ports, hpriv->cap);
pci_set_master(pdev);
diff --git a/drivers/scsi/libata-bmdma.c b/drivers/scsi/libata-bmdma.c
index 9ce221f..3268cf5 100644
--- a/drivers/scsi/libata-bmdma.c
+++ b/drivers/scsi/libata-bmdma.c
@@ -797,32 +797,6 @@
}
#ifdef CONFIG_PCI
-static struct ata_probe_ent *
-ata_probe_ent_alloc(struct device *dev, const struct ata_port_info *port)
-{
- struct ata_probe_ent *probe_ent;
-
- probe_ent = kzalloc(sizeof(*probe_ent), GFP_KERNEL);
- if (!probe_ent) {
- printk(KERN_ERR DRV_NAME "(%s): out of memory\n",
- kobject_name(&(dev->kobj)));
- return NULL;
- }
-
- INIT_LIST_HEAD(&probe_ent->node);
- probe_ent->dev = dev;
-
- probe_ent->sht = port->sht;
- probe_ent->host_flags = port->host_flags;
- probe_ent->pio_mask = port->pio_mask;
- probe_ent->mwdma_mask = port->mwdma_mask;
- probe_ent->udma_mask = port->udma_mask;
- probe_ent->port_ops = port->port_ops;
-
- return probe_ent;
-}
-
-
/**
* ata_pci_init_native_mode - Initialize native-mode driver
* @pdev: pci device to be initialized
diff --git a/drivers/scsi/libata-core.c b/drivers/scsi/libata-core.c
index 16fc2dd..83d93fc 100644
--- a/drivers/scsi/libata-core.c
+++ b/drivers/scsi/libata-core.c
@@ -1528,7 +1528,7 @@
* Zero on success, negative errno otherwise.
*/
-static int ata_bus_probe(struct ata_port *ap)
+int ata_bus_probe(struct ata_port *ap)
{
unsigned int classes[ATA_MAX_DEVICES];
int tries[ATA_MAX_DEVICES];
@@ -5218,35 +5218,25 @@
}
/**
- * ata_host_init - Initialize an ata_port structure
+ * ata_port_init - Initialize an ata_port structure
* @ap: Structure to initialize
- * @host: associated SCSI mid-layer structure
* @host_set: Collection of hosts to which @ap belongs
* @ent: Probe information provided by low-level driver
* @port_no: Port number associated with this ata_port
*
- * Initialize a new ata_port structure, and its associated
- * scsi_host.
+ * Initialize a new ata_port structure.
*
* LOCKING:
* Inherited from caller.
*/
-static void ata_host_init(struct ata_port *ap, struct Scsi_Host *host,
- struct ata_host_set *host_set,
- const struct ata_probe_ent *ent, unsigned int port_no)
+void ata_port_init(struct ata_port *ap, struct ata_host_set *host_set,
+ const struct ata_probe_ent *ent, unsigned int port_no)
{
unsigned int i;
- host->max_id = 16;
- host->max_lun = 1;
- host->max_channel = 1;
- host->unique_id = ata_unique_id++;
- host->max_cmd_len = 12;
-
ap->lock = &host_set->lock;
ap->flags = ATA_FLAG_DISABLED;
- ap->id = host->unique_id;
- ap->host = host;
+ ap->id = ata_unique_id++;
ap->ctl = ATA_DEVCTL_OBS;
ap->host_set = host_set;
ap->dev = ent->dev;
@@ -5298,6 +5288,35 @@
}
/**
+ * ata_host_init - Initialize an ata_port structure
+ * @ap: Structure to initialize
+ * @host: associated SCSI mid-layer structure
+ * @host_set: Collection of hosts to which @ap belongs
+ * @ent: Probe information provided by low-level driver
+ * @port_no: Port number associated with this ata_port
+ *
+ * Initialize a new ata_port structure, and its associated
+ * scsi_host.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+
+static void ata_host_init(struct ata_port *ap, struct Scsi_Host *host,
+ struct ata_host_set *host_set,
+ const struct ata_probe_ent *ent, unsigned int port_no)
+{
+ ata_port_init(ap, host_set, ent, port_no);
+ ap->host = host;
+
+ host->unique_id = ap->id;
+ host->max_id = 16;
+ host->max_lun = 1;
+ host->max_channel = 1;
+ host->max_cmd_len = 12;
+}
+
+/**
* ata_host_add - Attach low-level ATA driver to system
* @ent: Information provided by low-level driver
* @host_set: Collections of ports to which we add
@@ -5351,6 +5370,28 @@
}
/**
+ * ata_sas_host_init - Initialize a host_set struct
+ * @host_set: host_set to initialize
+ * @dev: device host_set is attached to
+ * @flags: host_set flags
+ * @ops: port_ops
+ *
+ * LOCKING:
+ * PCI/etc. bus probe sem.
+ *
+ */
+
+void ata_host_set_init(struct ata_host_set *host_set,
+ struct device *dev, unsigned long flags,
+ const struct ata_port_operations *ops)
+{
+ spin_lock_init(&host_set->lock);
+ host_set->dev = dev;
+ host_set->flags = flags;
+ host_set->ops = ops;
+}
+
+/**
* ata_device_add - Register hardware device with ATA and SCSI layers
* @ent: Probe information describing hardware device to be registered
*
@@ -5381,15 +5422,12 @@
(ent->n_ports * sizeof(void *)), GFP_KERNEL);
if (!host_set)
return 0;
- spin_lock_init(&host_set->lock);
- host_set->dev = dev;
+ ata_host_set_init(host_set, dev, ent->host_set_flags, ent->port_ops);
host_set->n_ports = ent->n_ports;
host_set->irq = ent->irq;
host_set->mmio_base = ent->mmio_base;
host_set->private_data = ent->private_data;
- host_set->ops = ent->port_ops;
- host_set->flags = ent->host_set_flags;
/* register each port bound to this device */
for (i = 0; i < ent->n_ports; i++) {
@@ -5650,6 +5688,31 @@
return 1;
}
+struct ata_probe_ent *
+ata_probe_ent_alloc(struct device *dev, const struct ata_port_info *port)
+{
+ struct ata_probe_ent *probe_ent;
+
+ probe_ent = kzalloc(sizeof(*probe_ent), GFP_KERNEL);
+ if (!probe_ent) {
+ printk(KERN_ERR DRV_NAME "(%s): out of memory\n",
+ kobject_name(&(dev->kobj)));
+ return NULL;
+ }
+
+ INIT_LIST_HEAD(&probe_ent->node);
+ probe_ent->dev = dev;
+
+ probe_ent->sht = port->sht;
+ probe_ent->host_flags = port->host_flags;
+ probe_ent->pio_mask = port->pio_mask;
+ probe_ent->mwdma_mask = port->mwdma_mask;
+ probe_ent->udma_mask = port->udma_mask;
+ probe_ent->port_ops = port->port_ops;
+
+ return probe_ent;
+}
+
/**
* ata_std_ports - initialize ioaddr with standard port offsets.
* @ioaddr: IO address structure to be initialized
@@ -5749,11 +5812,11 @@
return (tmp == bits->val) ? 1 : 0;
}
-void ata_pci_device_do_suspend(struct pci_dev *pdev, pm_message_t state)
+void ata_pci_device_do_suspend(struct pci_dev *pdev, pm_message_t mesg)
{
pci_save_state(pdev);
- if (state.event == PM_EVENT_SUSPEND) {
+ if (mesg.event == PM_EVENT_SUSPEND) {
pci_disable_device(pdev);
pci_set_power_state(pdev, PCI_D3hot);
}
@@ -5767,24 +5830,24 @@
pci_set_master(pdev);
}
-int ata_pci_device_suspend(struct pci_dev *pdev, pm_message_t state)
+int ata_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
{
struct ata_host_set *host_set = dev_get_drvdata(&pdev->dev);
int rc = 0;
- rc = ata_host_set_suspend(host_set, state);
+ rc = ata_host_set_suspend(host_set, mesg);
if (rc)
return rc;
if (host_set->next) {
- rc = ata_host_set_suspend(host_set->next, state);
+ rc = ata_host_set_suspend(host_set->next, mesg);
if (rc) {
ata_host_set_resume(host_set);
return rc;
}
}
- ata_pci_device_do_suspend(pdev, state);
+ ata_pci_device_do_suspend(pdev, mesg);
return 0;
}
@@ -5908,6 +5971,7 @@
EXPORT_SYMBOL_GPL(sata_deb_timing_long);
EXPORT_SYMBOL_GPL(ata_std_bios_param);
EXPORT_SYMBOL_GPL(ata_std_ports);
+EXPORT_SYMBOL_GPL(ata_host_set_init);
EXPORT_SYMBOL_GPL(ata_device_add);
EXPORT_SYMBOL_GPL(ata_port_detach);
EXPORT_SYMBOL_GPL(ata_host_set_remove);
diff --git a/drivers/scsi/libata-scsi.c b/drivers/scsi/libata-scsi.c
index e92c31d..d168e3413 100644
--- a/drivers/scsi/libata-scsi.c
+++ b/drivers/scsi/libata-scsi.c
@@ -400,7 +400,7 @@
/**
* ata_scsi_device_suspend - suspend ATA device associated with sdev
* @sdev: the SCSI device to suspend
- * @state: target power management state
+ * @mesg: target power management message
*
* Request suspend EH action on the ATA device associated with
* @sdev and wait for the operation to complete.
@@ -411,7 +411,7 @@
* RETURNS:
* 0 on success, -errno otherwise.
*/
-int ata_scsi_device_suspend(struct scsi_device *sdev, pm_message_t state)
+int ata_scsi_device_suspend(struct scsi_device *sdev, pm_message_t mesg)
{
struct ata_port *ap = ata_shost_to_port(sdev->host);
struct ata_device *dev = ata_scsi_find_dev(ap, sdev);
@@ -438,7 +438,7 @@
/* request suspend */
action = ATA_EH_SUSPEND;
- if (state.event != PM_EVENT_SUSPEND)
+ if (mesg.event != PM_EVENT_SUSPEND)
action |= ATA_EH_PM_FREEZE;
ap->eh_info.dev_action[dev->devno] |= action;
ap->eh_info.flags |= ATA_EHI_QUIET;
@@ -463,7 +463,7 @@
spin_unlock_irqrestore(ap->lock, flags);
out:
if (rc == 0)
- sdev->sdev_gendev.power.power_state = state;
+ sdev->sdev_gendev.power.power_state = mesg;
return rc;
}
@@ -3171,3 +3171,152 @@
scsi_rescan_device(&(dev->sdev->sdev_gendev));
}
}
+
+/**
+ * ata_sas_port_alloc - Allocate port for a SAS attached SATA device
+ * @pdev: PCI device that the scsi device is attached to
+ * @port_info: Information from low-level host driver
+ * @host: SCSI host that the scsi device is attached to
+ *
+ * LOCKING:
+ * PCI/etc. bus probe sem.
+ *
+ * RETURNS:
+ * ata_port pointer on success / NULL on failure.
+ */
+
+struct ata_port *ata_sas_port_alloc(struct ata_host_set *host_set,
+ struct ata_port_info *port_info,
+ struct Scsi_Host *host)
+{
+ struct ata_port *ap = kzalloc(sizeof(*ap), GFP_KERNEL);
+ struct ata_probe_ent *ent;
+
+ if (!ap)
+ return NULL;
+
+ ent = ata_probe_ent_alloc(host_set->dev, port_info);
+ if (!ent) {
+ kfree(ap);
+ return NULL;
+ }
+
+ ata_port_init(ap, host_set, ent, 0);
+ ap->lock = host->host_lock;
+ kfree(ent);
+ return ap;
+}
+EXPORT_SYMBOL_GPL(ata_sas_port_alloc);
+
+/**
+ * ata_sas_port_start - Set port up for dma.
+ * @ap: Port to initialize
+ *
+ * Called just after data structures for each port are
+ * initialized. Allocates DMA pad.
+ *
+ * May be used as the port_start() entry in ata_port_operations.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+int ata_sas_port_start(struct ata_port *ap)
+{
+ return ata_pad_alloc(ap, ap->dev);
+}
+EXPORT_SYMBOL_GPL(ata_sas_port_start);
+
+/**
+ * ata_port_stop - Undo ata_sas_port_start()
+ * @ap: Port to shut down
+ *
+ * Frees the DMA pad.
+ *
+ * May be used as the port_stop() entry in ata_port_operations.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+
+void ata_sas_port_stop(struct ata_port *ap)
+{
+ ata_pad_free(ap, ap->dev);
+}
+EXPORT_SYMBOL_GPL(ata_sas_port_stop);
+
+/**
+ * ata_sas_port_init - Initialize a SATA device
+ * @ap: SATA port to initialize
+ *
+ * LOCKING:
+ * PCI/etc. bus probe sem.
+ *
+ * RETURNS:
+ * Zero on success, non-zero on error.
+ */
+
+int ata_sas_port_init(struct ata_port *ap)
+{
+ int rc = ap->ops->port_start(ap);
+
+ if (!rc)
+ rc = ata_bus_probe(ap);
+
+ return rc;
+}
+EXPORT_SYMBOL_GPL(ata_sas_port_init);
+
+/**
+ * ata_sas_port_destroy - Destroy a SATA port allocated by ata_sas_port_alloc
+ * @ap: SATA port to destroy
+ *
+ */
+
+void ata_sas_port_destroy(struct ata_port *ap)
+{
+ ap->ops->port_stop(ap);
+ kfree(ap);
+}
+EXPORT_SYMBOL_GPL(ata_sas_port_destroy);
+
+/**
+ * ata_sas_slave_configure - Default slave_config routine for libata devices
+ * @sdev: SCSI device to configure
+ * @ap: ATA port to which SCSI device is attached
+ *
+ * RETURNS:
+ * Zero.
+ */
+
+int ata_sas_slave_configure(struct scsi_device *sdev, struct ata_port *ap)
+{
+ ata_scsi_sdev_config(sdev);
+ ata_scsi_dev_config(sdev, ap->device);
+ return 0;
+}
+EXPORT_SYMBOL_GPL(ata_sas_slave_configure);
+
+/**
+ * ata_sas_queuecmd - Issue SCSI cdb to libata-managed device
+ * @cmd: SCSI command to be sent
+ * @done: Completion function, called when command is complete
+ * @ap: ATA port to which the command is being sent
+ *
+ * RETURNS:
+ * Zero.
+ */
+
+int ata_sas_queuecmd(struct scsi_cmnd *cmd, void (*done)(struct scsi_cmnd *),
+ struct ata_port *ap)
+{
+ ata_scsi_dump_cdb(ap, cmd);
+
+ if (likely(ata_scsi_dev_enabled(ap->device)))
+ __ata_scsi_queuecmd(cmd, done, ap->device);
+ else {
+ cmd->result = (DID_BAD_TARGET << 16);
+ done(cmd);
+ }
+ return 0;
+}
+EXPORT_SYMBOL_GPL(ata_sas_queuecmd);
diff --git a/drivers/scsi/libata.h b/drivers/scsi/libata.h
index c325679..d4a4f82 100644
--- a/drivers/scsi/libata.h
+++ b/drivers/scsi/libata.h
@@ -69,6 +69,10 @@
extern void ata_dev_init(struct ata_device *dev);
extern int ata_task_ioctl(struct scsi_device *scsidev, void __user *arg);
extern int ata_cmd_ioctl(struct scsi_device *scsidev, void __user *arg);
+extern void ata_port_init(struct ata_port *ap, struct ata_host_set *host_set,
+ const struct ata_probe_ent *ent, unsigned int port_no);
+extern struct ata_probe_ent *ata_probe_ent_alloc(struct device *dev,
+ const struct ata_port_info *port);
/* libata-scsi.c */
@@ -107,6 +111,7 @@
u8 *rbuf, unsigned int buflen));
extern void ata_schedule_scsi_eh(struct Scsi_Host *shost);
extern void ata_scsi_dev_rescan(void *data);
+extern int ata_bus_probe(struct ata_port *ap);
/* libata-eh.c */
extern enum scsi_eh_timer_return ata_scsi_timed_out(struct scsi_cmnd *cmd);
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 66c3100..cf5eb1d 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -676,19 +676,30 @@
extern int ata_pci_init_one (struct pci_dev *pdev, struct ata_port_info **port_info,
unsigned int n_ports);
extern void ata_pci_remove_one (struct pci_dev *pdev);
-extern void ata_pci_device_do_suspend(struct pci_dev *pdev, pm_message_t state);
+extern void ata_pci_device_do_suspend(struct pci_dev *pdev, pm_message_t mesg);
extern void ata_pci_device_do_resume(struct pci_dev *pdev);
-extern int ata_pci_device_suspend(struct pci_dev *pdev, pm_message_t state);
+extern int ata_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg);
extern int ata_pci_device_resume(struct pci_dev *pdev);
extern int ata_pci_clear_simplex(struct pci_dev *pdev);
#endif /* CONFIG_PCI */
extern int ata_device_add(const struct ata_probe_ent *ent);
extern void ata_port_detach(struct ata_port *ap);
+extern void ata_host_set_init(struct ata_host_set *, struct device *,
+ unsigned long, const struct ata_port_operations *);
extern void ata_host_set_remove(struct ata_host_set *host_set);
extern int ata_scsi_detect(struct scsi_host_template *sht);
extern int ata_scsi_ioctl(struct scsi_device *dev, int cmd, void __user *arg);
extern int ata_scsi_queuecmd(struct scsi_cmnd *cmd, void (*done)(struct scsi_cmnd *));
extern int ata_scsi_release(struct Scsi_Host *host);
+extern void ata_sas_port_destroy(struct ata_port *);
+extern struct ata_port *ata_sas_port_alloc(struct ata_host_set *,
+ struct ata_port_info *, struct Scsi_Host *);
+extern int ata_sas_port_init(struct ata_port *);
+extern int ata_sas_port_start(struct ata_port *ap);
+extern void ata_sas_port_stop(struct ata_port *ap);
+extern int ata_sas_slave_configure(struct scsi_device *, struct ata_port *);
+extern int ata_sas_queuecmd(struct scsi_cmnd *cmd, void (*done)(struct scsi_cmnd *),
+ struct ata_port *ap);
extern unsigned int ata_host_intr(struct ata_port *ap, struct ata_queued_cmd *qc);
extern int sata_scr_valid(struct ata_port *ap);
extern int sata_scr_read(struct ata_port *ap, int reg, u32 *val);
@@ -697,7 +708,7 @@
extern int ata_port_online(struct ata_port *ap);
extern int ata_port_offline(struct ata_port *ap);
extern int ata_scsi_device_resume(struct scsi_device *);
-extern int ata_scsi_device_suspend(struct scsi_device *, pm_message_t state);
+extern int ata_scsi_device_suspend(struct scsi_device *, pm_message_t mesg);
extern int ata_host_set_suspend(struct ata_host_set *host_set,
pm_message_t mesg);
extern void ata_host_set_resume(struct ata_host_set *host_set);