Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/Documentation/usb/hotplug.txt b/Documentation/usb/hotplug.txt
new file mode 100644
index 0000000..f531706
--- /dev/null
+++ b/Documentation/usb/hotplug.txt
@@ -0,0 +1,148 @@
+LINUX HOTPLUGGING
+
+In hotpluggable busses like USB (and Cardbus PCI), end-users plug devices
+into the bus with power on. In most cases, users expect the devices to become
+immediately usable. That means the system must do many things, including:
+
+ - Find a driver that can handle the device. That may involve
+ loading a kernel module; newer drivers can use module-init-tools
+ to publish their device (and class) support to user utilities.
+
+ - Bind a driver to that device. Bus frameworks do that using a
+ device driver's probe() routine.
+
+ - Tell other subsystems to configure the new device. Print
+ queues may need to be enabled, networks brought up, disk
+ partitions mounted, and so on. In some cases these will
+ be driver-specific actions.
+
+This involves a mix of kernel mode and user mode actions. Making devices
+be immediately usable means that any user mode actions can't wait for an
+administrator to do them: the kernel must trigger them, either passively
+(triggering some monitoring daemon to invoke a helper program) or
+actively (calling such a user mode helper program directly).
+
+Those triggered actions must support a system's administrative policies;
+such programs are called "policy agents" here. Typically they involve
+shell scripts that dispatch to more familiar administration tools.
+
+Because some of those actions rely on information about drivers (metadata)
+that is currently available only when the drivers are dynamically linked,
+you get the best hotplugging when you configure a highly modular system.
+
+
+KERNEL HOTPLUG HELPER (/sbin/hotplug)
+
+When you compile with CONFIG_HOTPLUG, you get a new kernel parameter:
+/proc/sys/kernel/hotplug, which normally holds the pathname "/sbin/hotplug".
+That parameter names a program which the kernel may invoke at various times.
+
+The /sbin/hotplug program can be invoked by any subsystem as part of its
+reaction to a configuration change, from a thread in that subsystem.
+Only one parameter is required: the name of a subsystem being notified of
+some kernel event. That name is used as the first key for further event
+dispatch; any other argument and environment parameters are specified by
+the subsystem making that invocation.
+
+Hotplug software and other resources is available at:
+
+ http://linux-hotplug.sourceforge.net
+
+Mailing list information is also available at that site.
+
+
+--------------------------------------------------------------------------
+
+
+USB POLICY AGENT
+
+The USB subsystem currently invokes /sbin/hotplug when USB devices
+are added or removed from system. The invocation is done by the kernel
+hub daemon thread [khubd], or else as part of root hub initialization
+(done by init, modprobe, kapmd, etc). Its single command line parameter
+is the string "usb", and it passes these environment variables:
+
+ ACTION ... "add", "remove"
+ PRODUCT ... USB vendor, product, and version codes (hex)
+ TYPE ... device class codes (decimal)
+ INTERFACE ... interface 0 class codes (decimal)
+
+If "usbdevfs" is configured, DEVICE and DEVFS are also passed. DEVICE is
+the pathname of the device, and is useful for devices with multiple and/or
+alternate interfaces that complicate driver selection. By design, USB
+hotplugging is independent of "usbdevfs": you can do most essential parts
+of USB device setup without using that filesystem, and without running a
+user mode daemon to detect changes in system configuration.
+
+Currently available policy agent implementations can load drivers for
+modules, and can invoke driver-specific setup scripts. The newest ones
+leverage USB module-init-tools support. Later agents might unload drivers.
+
+
+USB MODUTILS SUPPORT
+
+Current versions of module-init-tools will create a "modules.usbmap" file
+which contains the entries from each driver's MODULE_DEVICE_TABLE. Such
+files can be used by various user mode policy agents to make sure all the
+right driver modules get loaded, either at boot time or later.
+
+See <linux/usb.h> for full information about such table entries; or look
+at existing drivers. Each table entry describes one or more criteria to
+be used when matching a driver to a device or class of devices. The
+specific criteria are identified by bits set in "match_flags", paired
+with field values. You can construct the criteria directly, or with
+macros such as these, and use driver_info to store more information.
+
+ USB_DEVICE (vendorId, productId)
+ ... matching devices with specified vendor and product ids
+ USB_DEVICE_VER (vendorId, productId, lo, hi)
+ ... like USB_DEVICE with lo <= productversion <= hi
+ USB_INTERFACE_INFO (class, subclass, protocol)
+ ... matching specified interface class info
+ USB_DEVICE_INFO (class, subclass, protocol)
+ ... matching specified device class info
+
+A short example, for a driver that supports several specific USB devices
+and their quirks, might have a MODULE_DEVICE_TABLE like this:
+
+ static const struct usb_device_id mydriver_id_table = {
+ { USB_DEVICE (0x9999, 0xaaaa), driver_info: QUIRK_X },
+ { USB_DEVICE (0xbbbb, 0x8888), driver_info: QUIRK_Y|QUIRK_Z },
+ ...
+ { } /* end with an all-zeroes entry */
+ }
+ MODULE_DEVICE_TABLE (usb, mydriver_id_table);
+
+Most USB device drivers should pass these tables to the USB subsystem as
+well as to the module management subsystem. Not all, though: some driver
+frameworks connect using interfaces layered over USB, and so they won't
+need such a "struct usb_driver".
+
+Drivers that connect directly to the USB subsystem should be declared
+something like this:
+
+ static struct usb_driver mydriver = {
+ .name = "mydriver",
+ .id_table = mydriver_id_table,
+ .probe = my_probe,
+ .disconnect = my_disconnect,
+
+ /*
+ if using the usb chardev framework:
+ .minor = MY_USB_MINOR_START,
+ .fops = my_file_ops,
+ if exposing any operations through usbdevfs:
+ .ioctl = my_ioctl,
+ */
+ }
+
+When the USB subsystem knows about a driver's device ID table, it's used when
+choosing drivers to probe(). The thread doing new device processing checks
+drivers' device ID entries from the MODULE_DEVICE_TABLE against interface and
+device descriptors for the device. It will only call probe() if there is a
+match, and the third argument to probe() will be the entry that matched.
+
+If you don't provide an id_table for your driver, then your driver may get
+probed for each new device; the third parameter to probe() will be null.
+
+